drivers/ata/sata

/* [<][>][^][v][top][bottom][index][help] */
This source file includes following definitions.
gemini_sata_bridge_get
gemini_sata_bridge_enabled
gemini_sata_get_muxmode
gemini_sata_setup_bridge
gemini_sata_start_bridge
gemini_sata_stop_bridge
gemini_sata_reset_bridge
gemini_sata_bridge_init
gemini_setup_ide_pins
gemini_sata_probe
gemini_sata_remove
   1 // SPDX-License-Identifier: GPL-2.0-only
   2 /*
   3  * Cortina Systems Gemini SATA bridge add-on to Faraday FTIDE010
   4  * Copyright (C) 2017 Linus Walleij <linus.walleij@linaro.org>
   5  */
   6 
   7 #include <linux/init.h>
   8 #include <linux/module.h>
   9 #include <linux/platform_device.h>
  10 #include <linux/bitops.h>
  11 #include <linux/mfd/syscon.h>
  12 #include <linux/regmap.h>
  13 #include <linux/delay.h>
  14 #include <linux/reset.h>
  15 #include <linux/of_address.h>
  16 #include <linux/of_device.h>
  17 #include <linux/clk.h>
  18 #include <linux/io.h>
  19 #include <linux/pinctrl/consumer.h>
  20 #include "sata_gemini.h"
  21 
  22 #define DRV_NAME "gemini_sata_bridge"
  23 
  24 /**
  25  * struct sata_gemini - a state container for a Gemini SATA bridge
  26  * @dev: the containing device
  27  * @base: remapped I/O memory base
  28  * @muxmode: the current muxing mode
  29  * @ide_pins: if the device is using the plain IDE interface pins
  30  * @sata_bridge: if the device enables the SATA bridge
  31  * @sata0_reset: SATA0 reset handler
  32  * @sata1_reset: SATA1 reset handler
  33  * @sata0_pclk: SATA0 PCLK handler
  34  * @sata1_pclk: SATA1 PCLK handler
  35  */
  36 struct sata_gemini {
  37         struct device *dev;
  38         void __iomem *base;
  39         enum gemini_muxmode muxmode;
  40         bool ide_pins;
  41         bool sata_bridge;
  42         struct reset_control *sata0_reset;
  43         struct reset_control *sata1_reset;
  44         struct clk *sata0_pclk;
  45         struct clk *sata1_pclk;
  46 };
  47 
  48 /* Miscellaneous Control Register */
  49 #define GEMINI_GLOBAL_MISC_CTRL         0x30
  50 /*
  51  * Values of IDE IOMUX bits in the misc control register
  52  *
  53  * Bits 26:24 are "IDE IO Select", which decides what SATA
  54  * adapters are connected to which of the two IDE/ATA
  55  * controllers in the Gemini. We can connect the two IDE blocks
  56  * to one SATA adapter each, both acting as master, or one IDE
  57  * blocks to two SATA adapters so the IDE block can act in a
  58  * master/slave configuration.
  59  *
  60  * We also bring out different blocks on the actual IDE
  61  * pins (not SATA pins) if (and only if) these are muxed in.
  62  *
  63  * 111-100 - Reserved
  64  * Mode 0: 000 - ata0 master <-> sata0
  65  *               ata1 master <-> sata1
  66  *               ata0 slave interface brought out on IDE pads
  67  * Mode 1: 001 - ata0 master <-> sata0
  68  *               ata1 master <-> sata1
  69  *               ata1 slave interface brought out on IDE pads
  70  * Mode 2: 010 - ata1 master <-> sata1
  71  *               ata1 slave  <-> sata0
  72  *               ata0 master and slave interfaces brought out
  73  *                    on IDE pads
  74  * Mode 3: 011 - ata0 master <-> sata0
  75  *               ata1 slave  <-> sata1
  76  *               ata1 master and slave interfaces brought out
  77  *                    on IDE pads
  78  */
  79 #define GEMINI_IDE_IOMUX_MASK                   (7 << 24)
  80 #define GEMINI_IDE_IOMUX_MODE0                  (0 << 24)
  81 #define GEMINI_IDE_IOMUX_MODE1                  (1 << 24)
  82 #define GEMINI_IDE_IOMUX_MODE2                  (2 << 24)
  83 #define GEMINI_IDE_IOMUX_MODE3                  (3 << 24)
  84 #define GEMINI_IDE_IOMUX_SHIFT                  (24)
  85 
  86 /*
  87  * Registers directly controlling the PATA<->SATA adapters
  88  */
  89 #define GEMINI_SATA_ID                          0x00
  90 #define GEMINI_SATA_PHY_ID                      0x04
  91 #define GEMINI_SATA0_STATUS                     0x08
  92 #define GEMINI_SATA1_STATUS                     0x0c
  93 #define GEMINI_SATA0_CTRL                       0x18
  94 #define GEMINI_SATA1_CTRL                       0x1c
  95 
  96 #define GEMINI_SATA_STATUS_BIST_DONE            BIT(5)
  97 #define GEMINI_SATA_STATUS_BIST_OK              BIT(4)
  98 #define GEMINI_SATA_STATUS_PHY_READY            BIT(0)
  99 
 100 #define GEMINI_SATA_CTRL_PHY_BIST_EN            BIT(14)
 101 #define GEMINI_SATA_CTRL_PHY_FORCE_IDLE         BIT(13)
 102 #define GEMINI_SATA_CTRL_PHY_FORCE_READY        BIT(12)
 103 #define GEMINI_SATA_CTRL_PHY_AFE_LOOP_EN        BIT(10)
 104 #define GEMINI_SATA_CTRL_PHY_DIG_LOOP_EN        BIT(9)
 105 #define GEMINI_SATA_CTRL_HOTPLUG_DETECT_EN      BIT(4)
 106 #define GEMINI_SATA_CTRL_ATAPI_EN               BIT(3)
 107 #define GEMINI_SATA_CTRL_BUS_WITH_20            BIT(2)
 108 #define GEMINI_SATA_CTRL_SLAVE_EN               BIT(1)
 109 #define GEMINI_SATA_CTRL_EN                     BIT(0)
 110 
 111 /*
 112  * There is only ever one instance of this bridge on a system,
 113  * so create a singleton so that the FTIDE010 instances can grab
 114  * a reference to it.
 115  */
 116 static struct sata_gemini *sg_singleton;
 117 
 118 struct sata_gemini *gemini_sata_bridge_get(void)
 119 {
 120         if (sg_singleton)
 121                 return sg_singleton;
 122         return ERR_PTR(-EPROBE_DEFER);
 123 }
 124 EXPORT_SYMBOL(gemini_sata_bridge_get);
 125 
 126 bool gemini_sata_bridge_enabled(struct sata_gemini *sg, bool is_ata1)
 127 {
 128         if (!sg->sata_bridge)
 129                 return false;
 130         /*
 131          * In muxmode 2 and 3 one of the ATA controllers is
 132          * actually not connected to any SATA bridge.
 133          */
 134         if ((sg->muxmode == GEMINI_MUXMODE_2) &&
 135             !is_ata1)
 136                 return false;
 137         if ((sg->muxmode == GEMINI_MUXMODE_3) &&
 138             is_ata1)
 139                 return false;
 140 
 141         return true;
 142 }
 143 EXPORT_SYMBOL(gemini_sata_bridge_enabled);
 144 
 145 enum gemini_muxmode gemini_sata_get_muxmode(struct sata_gemini *sg)
 146 {
 147         return sg->muxmode;
 148 }
 149 EXPORT_SYMBOL(gemini_sata_get_muxmode);
 150 
 151 static int gemini_sata_setup_bridge(struct sata_gemini *sg,
 152                                     unsigned int bridge)
 153 {
 154         unsigned long timeout = jiffies + (HZ * 1);
 155         bool bridge_online;
 156         u32 val;
 157 
 158         if (bridge == 0) {
 159                 val = GEMINI_SATA_CTRL_HOTPLUG_DETECT_EN | GEMINI_SATA_CTRL_EN;
 160                 /* SATA0 slave mode is only used in muxmode 2 */
 161                 if (sg->muxmode == GEMINI_MUXMODE_2)
 162                         val |= GEMINI_SATA_CTRL_SLAVE_EN;
 163                 writel(val, sg->base + GEMINI_SATA0_CTRL);
 164         } else {
 165                 val = GEMINI_SATA_CTRL_HOTPLUG_DETECT_EN | GEMINI_SATA_CTRL_EN;
 166                 /* SATA1 slave mode is only used in muxmode 3 */
 167                 if (sg->muxmode == GEMINI_MUXMODE_3)
 168                         val |= GEMINI_SATA_CTRL_SLAVE_EN;
 169                 writel(val, sg->base + GEMINI_SATA1_CTRL);
 170         }
 171 
 172         /* Vendor code waits 10 ms here */
 173         msleep(10);
 174 
 175         /* Wait for PHY to become ready */
 176         do {
 177                 msleep(100);
 178 
 179                 if (bridge == 0)
 180                         val = readl(sg->base + GEMINI_SATA0_STATUS);
 181                 else
 182                         val = readl(sg->base + GEMINI_SATA1_STATUS);
 183                 if (val & GEMINI_SATA_STATUS_PHY_READY)
 184                         break;
 185         } while (time_before(jiffies, timeout));
 186 
 187         bridge_online = !!(val & GEMINI_SATA_STATUS_PHY_READY);
 188 
 189         dev_info(sg->dev, "SATA%d PHY %s\n", bridge,
 190                  bridge_online ? "ready" : "not ready");
 191 
 192         return bridge_online ? 0: -ENODEV;
 193 }
 194 
 195 int gemini_sata_start_bridge(struct sata_gemini *sg, unsigned int bridge)
 196 {
 197         struct clk *pclk;
 198         int ret;
 199 
 200         if (bridge == 0)
 201                 pclk = sg->sata0_pclk;
 202         else
 203                 pclk = sg->sata1_pclk;
 204         clk_enable(pclk);
 205         msleep(10);
 206 
 207         /* Do not keep clocking a bridge that is not online */
 208         ret = gemini_sata_setup_bridge(sg, bridge);
 209         if (ret)
 210                 clk_disable(pclk);
 211 
 212         return ret;
 213 }
 214 EXPORT_SYMBOL(gemini_sata_start_bridge);
 215 
 216 void gemini_sata_stop_bridge(struct sata_gemini *sg, unsigned int bridge)
 217 {
 218         if (bridge == 0)
 219                 clk_disable(sg->sata0_pclk);
 220         else if (bridge == 1)
 221                 clk_disable(sg->sata1_pclk);
 222 }
 223 EXPORT_SYMBOL(gemini_sata_stop_bridge);
 224 
 225 int gemini_sata_reset_bridge(struct sata_gemini *sg,
 226                              unsigned int bridge)
 227 {
 228         if (bridge == 0)
 229                 reset_control_reset(sg->sata0_reset);
 230         else
 231                 reset_control_reset(sg->sata1_reset);
 232         msleep(10);
 233         return gemini_sata_setup_bridge(sg, bridge);
 234 }
 235 EXPORT_SYMBOL(gemini_sata_reset_bridge);
 236 
 237 static int gemini_sata_bridge_init(struct sata_gemini *sg)
 238 {
 239         struct device *dev = sg->dev;
 240         u32 sata_id, sata_phy_id;
 241         int ret;
 242 
 243         sg->sata0_pclk = devm_clk_get(dev, "SATA0_PCLK");
 244         if (IS_ERR(sg->sata0_pclk)) {
 245                 dev_err(dev, "no SATA0 PCLK");
 246                 return -ENODEV;
 247         }
 248         sg->sata1_pclk = devm_clk_get(dev, "SATA1_PCLK");
 249         if (IS_ERR(sg->sata1_pclk)) {
 250                 dev_err(dev, "no SATA1 PCLK");
 251                 return -ENODEV;
 252         }
 253 
 254         ret = clk_prepare_enable(sg->sata0_pclk);
 255         if (ret) {
 256                 pr_err("failed to enable SATA0 PCLK\n");
 257                 return ret;
 258         }
 259         ret = clk_prepare_enable(sg->sata1_pclk);
 260         if (ret) {
 261                 pr_err("failed to enable SATA1 PCLK\n");
 262                 clk_disable_unprepare(sg->sata0_pclk);
 263                 return ret;
 264         }
 265 
 266         sg->sata0_reset = devm_reset_control_get_exclusive(dev, "sata0");
 267         if (IS_ERR(sg->sata0_reset)) {
 268                 dev_err(dev, "no SATA0 reset controller\n");
 269                 clk_disable_unprepare(sg->sata1_pclk);
 270                 clk_disable_unprepare(sg->sata0_pclk);
 271                 return PTR_ERR(sg->sata0_reset);
 272         }
 273         sg->sata1_reset = devm_reset_control_get_exclusive(dev, "sata1");
 274         if (IS_ERR(sg->sata1_reset)) {
 275                 dev_err(dev, "no SATA1 reset controller\n");
 276                 clk_disable_unprepare(sg->sata1_pclk);
 277                 clk_disable_unprepare(sg->sata0_pclk);
 278                 return PTR_ERR(sg->sata1_reset);
 279         }
 280 
 281         sata_id = readl(sg->base + GEMINI_SATA_ID);
 282         sata_phy_id = readl(sg->base + GEMINI_SATA_PHY_ID);
 283         sg->sata_bridge = true;
 284         clk_disable(sg->sata0_pclk);
 285         clk_disable(sg->sata1_pclk);
 286 
 287         dev_info(dev, "SATA ID %08x, PHY ID: %08x\n", sata_id, sata_phy_id);
 288 
 289         return 0;
 290 }
 291 
 292 static int gemini_setup_ide_pins(struct device *dev)
 293 {
 294         struct pinctrl *p;
 295         struct pinctrl_state *ide_state;
 296         int ret;
 297 
 298         p = devm_pinctrl_get(dev);
 299         if (IS_ERR(p))
 300                 return PTR_ERR(p);
 301 
 302         ide_state = pinctrl_lookup_state(p, "ide");
 303         if (IS_ERR(ide_state))
 304                 return PTR_ERR(ide_state);
 305 
 306         ret = pinctrl_select_state(p, ide_state);
 307         if (ret) {
 308                 dev_err(dev, "could not select IDE state\n");
 309                 return ret;
 310         }
 311 
 312         return 0;
 313 }
 314 
 315 static int gemini_sata_probe(struct platform_device *pdev)
 316 {
 317         struct device *dev = &pdev->dev;
 318         struct device_node *np = dev->of_node;
 319         struct sata_gemini *sg;
 320         struct regmap *map;
 321         struct resource *res;
 322         enum gemini_muxmode muxmode;
 323         u32 gmode;
 324         u32 gmask;
 325         int ret;
 326 
 327         sg = devm_kzalloc(dev, sizeof(*sg), GFP_KERNEL);
 328         if (!sg)
 329                 return -ENOMEM;
 330         sg->dev = dev;
 331 
 332         res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 333         if (!res)
 334                 return -ENODEV;
 335 
 336         sg->base = devm_ioremap_resource(dev, res);
 337         if (IS_ERR(sg->base))
 338                 return PTR_ERR(sg->base);
 339 
 340         map = syscon_regmap_lookup_by_phandle(np, "syscon");
 341         if (IS_ERR(map)) {
 342                 dev_err(dev, "no global syscon\n");
 343                 return PTR_ERR(map);
 344         }
 345 
 346         /* Set up the SATA bridge if need be */
 347         if (of_property_read_bool(np, "cortina,gemini-enable-sata-bridge")) {
 348                 ret = gemini_sata_bridge_init(sg);
 349                 if (ret)
 350                         return ret;
 351         }
 352 
 353         if (of_property_read_bool(np, "cortina,gemini-enable-ide-pins"))
 354                 sg->ide_pins = true;
 355 
 356         if (!sg->sata_bridge && !sg->ide_pins) {
 357                 dev_err(dev, "neither SATA bridge or IDE output enabled\n");
 358                 ret = -EINVAL;
 359                 goto out_unprep_clk;
 360         }
 361 
 362         ret = of_property_read_u32(np, "cortina,gemini-ata-muxmode", &muxmode);
 363         if (ret) {
 364                 dev_err(dev, "could not parse ATA muxmode\n");
 365                 goto out_unprep_clk;
 366         }
 367         if (muxmode > GEMINI_MUXMODE_3) {
 368                 dev_err(dev, "illegal muxmode %d\n", muxmode);
 369                 ret = -EINVAL;
 370                 goto out_unprep_clk;
 371         }
 372         sg->muxmode = muxmode;
 373         gmask = GEMINI_IDE_IOMUX_MASK;
 374         gmode = (muxmode << GEMINI_IDE_IOMUX_SHIFT);
 375 
 376         ret = regmap_update_bits(map, GEMINI_GLOBAL_MISC_CTRL, gmask, gmode);
 377         if (ret) {
 378                 dev_err(dev, "unable to set up IDE muxing\n");
 379                 ret = -ENODEV;
 380                 goto out_unprep_clk;
 381         }
 382 
 383         /*
 384          * Route out the IDE pins if desired.
 385          * This is done by looking up a special pin control state called
 386          * "ide" that will route out the IDE pins.
 387          */
 388         if (sg->ide_pins) {
 389                 ret = gemini_setup_ide_pins(dev);
 390                 if (ret)
 391                         return ret;
 392         }
 393 
 394         dev_info(dev, "set up the Gemini IDE/SATA nexus\n");
 395         platform_set_drvdata(pdev, sg);
 396         sg_singleton = sg;
 397 
 398         return 0;
 399 
 400 out_unprep_clk:
 401         if (sg->sata_bridge) {
 402                 clk_unprepare(sg->sata1_pclk);
 403                 clk_unprepare(sg->sata0_pclk);
 404         }
 405         return ret;
 406 }
 407 
 408 static int gemini_sata_remove(struct platform_device *pdev)
 409 {
 410         struct sata_gemini *sg = platform_get_drvdata(pdev);
 411 
 412         if (sg->sata_bridge) {
 413                 clk_unprepare(sg->sata1_pclk);
 414                 clk_unprepare(sg->sata0_pclk);
 415         }
 416         sg_singleton = NULL;
 417 
 418         return 0;
 419 }
 420 
 421 static const struct of_device_id gemini_sata_of_match[] = {
 422         {
 423                 .compatible = "cortina,gemini-sata-bridge",
 424         },
 425         {},
 426 };
 427 
 428 static struct platform_driver gemini_sata_driver = {
 429         .driver = {
 430                 .name = DRV_NAME,
 431                 .of_match_table = of_match_ptr(gemini_sata_of_match),
 432         },
 433         .probe = gemini_sata_probe,
 434         .remove = gemini_sata_remove,
 435 };
 436 module_platform_driver(gemini_sata_driver);
 437 
 438 MODULE_AUTHOR("Linus Walleij <linus.walleij@linaro.org>");
 439 MODULE_LICENSE("GPL");
 440 MODULE_ALIAS("platform:" DRV_NAME);
/* [<][>][^][v][top][bottom][index][help] */
root/drivers/ata/sata_gemini.c

DEFINITIONS
