drivers/ide/pdc202xx

/* [<][>][^][v][top][bottom][index][help] */
This source file includes following definitions.
max_dma_rate
get_indexed_reg
set_indexed_reg
pdcnew_set_dma_mode
pdcnew_set_pio_mode
pdcnew_cable_detect
pdcnew_reset
read_counter
detect_pll_input_clock
apple_kiwi_init
init_chipset_pdcnew
pdc20270_get_dev2
pdc202new_init_one
pdc202new_remove
pdc202new_ide_init
pdc202new_ide_exit
   1 // SPDX-License-Identifier: GPL-2.0-or-later
   2 /*
   3  *  Promise TX2/TX4/TX2000/133 IDE driver
   4  *
   5  *  Split from:
   6  *  linux/drivers/ide/pdc202xx.c        Version 0.35    Mar. 30, 2002
   7  *  Copyright (C) 1998-2002             Andre Hedrick <andre@linux-ide.org>
   8  *  Copyright (C) 2005-2007             MontaVista Software, Inc.
   9  *  Portions Copyright (C) 1999 Promise Technology, Inc.
  10  *  Author: Frank Tiernan (frankt@promise.com)
  11  *  Released under terms of General Public License
  12  */
  13 
  14 #include <linux/module.h>
  15 #include <linux/types.h>
  16 #include <linux/kernel.h>
  17 #include <linux/delay.h>
  18 #include <linux/pci.h>
  19 #include <linux/init.h>
  20 #include <linux/ide.h>
  21 #include <linux/ktime.h>
  22 
  23 #include <asm/io.h>
  24 
  25 #ifdef CONFIG_PPC_PMAC
  26 #include <asm/prom.h>
  27 #endif
  28 
  29 #define DRV_NAME "pdc202xx_new"
  30 
  31 #undef DEBUG
  32 
  33 #ifdef DEBUG
  34 #define DBG(fmt, args...) printk("%s: " fmt, __func__, ## args)
  35 #else
  36 #define DBG(fmt, args...)
  37 #endif
  38 
  39 static u8 max_dma_rate(struct pci_dev *pdev)
  40 {
  41         u8 mode;
  42 
  43         switch(pdev->device) {
  44                 case PCI_DEVICE_ID_PROMISE_20277:
  45                 case PCI_DEVICE_ID_PROMISE_20276:
  46                 case PCI_DEVICE_ID_PROMISE_20275:
  47                 case PCI_DEVICE_ID_PROMISE_20271:
  48                 case PCI_DEVICE_ID_PROMISE_20269:
  49                         mode = 4;
  50                         break;
  51                 case PCI_DEVICE_ID_PROMISE_20270:
  52                 case PCI_DEVICE_ID_PROMISE_20268:
  53                         mode = 3;
  54                         break;
  55                 default:
  56                         return 0;
  57         }
  58 
  59         return mode;
  60 }
  61 
  62 /**
  63  * get_indexed_reg - Get indexed register
  64  * @hwif: for the port address
  65  * @index: index of the indexed register
  66  */
  67 static u8 get_indexed_reg(ide_hwif_t *hwif, u8 index)
  68 {
  69         u8 value;
  70 
  71         outb(index, hwif->dma_base + 1);
  72         value = inb(hwif->dma_base + 3);
  73 
  74         DBG("index[%02X] value[%02X]\n", index, value);
  75         return value;
  76 }
  77 
  78 /**
  79  * set_indexed_reg - Set indexed register
  80  * @hwif: for the port address
  81  * @index: index of the indexed register
  82  */
  83 static void set_indexed_reg(ide_hwif_t *hwif, u8 index, u8 value)
  84 {
  85         outb(index, hwif->dma_base + 1);
  86         outb(value, hwif->dma_base + 3);
  87         DBG("index[%02X] value[%02X]\n", index, value);
  88 }
  89 
  90 /*
  91  * ATA Timing Tables based on 133 MHz PLL output clock.
  92  *
  93  * If the PLL outputs 100 MHz clock, the ASIC hardware will set
  94  * the timing registers automatically when "set features" command is
  95  * issued to the device. However, if the PLL output clock is 133 MHz,
  96  * the following tables must be used.
  97  */
  98 static struct pio_timing {
  99         u8 reg0c, reg0d, reg13;
 100 } pio_timings [] = {
 101         { 0xfb, 0x2b, 0xac },   /* PIO mode 0, IORDY off, Prefetch off */
 102         { 0x46, 0x29, 0xa4 },   /* PIO mode 1, IORDY off, Prefetch off */
 103         { 0x23, 0x26, 0x64 },   /* PIO mode 2, IORDY off, Prefetch off */
 104         { 0x27, 0x0d, 0x35 },   /* PIO mode 3, IORDY on,  Prefetch off */
 105         { 0x23, 0x09, 0x25 },   /* PIO mode 4, IORDY on,  Prefetch off */
 106 };
 107 
 108 static struct mwdma_timing {
 109         u8 reg0e, reg0f;
 110 } mwdma_timings [] = {
 111         { 0xdf, 0x5f },         /* MWDMA mode 0 */
 112         { 0x6b, 0x27 },         /* MWDMA mode 1 */
 113         { 0x69, 0x25 },         /* MWDMA mode 2 */
 114 };
 115 
 116 static struct udma_timing {
 117         u8 reg10, reg11, reg12;
 118 } udma_timings [] = {
 119         { 0x4a, 0x0f, 0xd5 },   /* UDMA mode 0 */
 120         { 0x3a, 0x0a, 0xd0 },   /* UDMA mode 1 */
 121         { 0x2a, 0x07, 0xcd },   /* UDMA mode 2 */
 122         { 0x1a, 0x05, 0xcd },   /* UDMA mode 3 */
 123         { 0x1a, 0x03, 0xcd },   /* UDMA mode 4 */
 124         { 0x1a, 0x02, 0xcb },   /* UDMA mode 5 */
 125         { 0x1a, 0x01, 0xcb },   /* UDMA mode 6 */
 126 };
 127 
 128 static void pdcnew_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 129 {
 130         struct pci_dev *dev     = to_pci_dev(hwif->dev);
 131         u8 adj                  = (drive->dn & 1) ? 0x08 : 0x00;
 132         const u8 speed          = drive->dma_mode;
 133 
 134         /*
 135          * IDE core issues SETFEATURES_XFER to the drive first (thanks to
 136          * IDE_HFLAG_POST_SET_MODE in ->host_flags).  PDC202xx hardware will
 137          * automatically set the timing registers based on 100 MHz PLL output.
 138          *
 139          * As we set up the PLL to output 133 MHz for UltraDMA/133 capable
 140          * chips, we must override the default register settings...
 141          */
 142         if (max_dma_rate(dev) == 4) {
 143                 u8 mode = speed & 0x07;
 144 
 145                 if (speed >= XFER_UDMA_0) {
 146                         set_indexed_reg(hwif, 0x10 + adj,
 147                                         udma_timings[mode].reg10);
 148                         set_indexed_reg(hwif, 0x11 + adj,
 149                                         udma_timings[mode].reg11);
 150                         set_indexed_reg(hwif, 0x12 + adj,
 151                                         udma_timings[mode].reg12);
 152                 } else {
 153                         set_indexed_reg(hwif, 0x0e + adj,
 154                                         mwdma_timings[mode].reg0e);
 155                         set_indexed_reg(hwif, 0x0f + adj,
 156                                         mwdma_timings[mode].reg0f);
 157                 }
 158         } else if (speed == XFER_UDMA_2) {
 159                 /* Set tHOLD bit to 0 if using UDMA mode 2 */
 160                 u8 tmp = get_indexed_reg(hwif, 0x10 + adj);
 161 
 162                 set_indexed_reg(hwif, 0x10 + adj, tmp & 0x7f);
 163         }
 164 }
 165 
 166 static void pdcnew_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 167 {
 168         struct pci_dev *dev = to_pci_dev(hwif->dev);
 169         u8 adj = (drive->dn & 1) ? 0x08 : 0x00;
 170         const u8 pio = drive->pio_mode - XFER_PIO_0;
 171 
 172         if (max_dma_rate(dev) == 4) {
 173                 set_indexed_reg(hwif, 0x0c + adj, pio_timings[pio].reg0c);
 174                 set_indexed_reg(hwif, 0x0d + adj, pio_timings[pio].reg0d);
 175                 set_indexed_reg(hwif, 0x13 + adj, pio_timings[pio].reg13);
 176         }
 177 }
 178 
 179 static u8 pdcnew_cable_detect(ide_hwif_t *hwif)
 180 {
 181         if (get_indexed_reg(hwif, 0x0b) & 0x04)
 182                 return ATA_CBL_PATA40;
 183         else
 184                 return ATA_CBL_PATA80;
 185 }
 186 
 187 static void pdcnew_reset(ide_drive_t *drive)
 188 {
 189         /*
 190          * Deleted this because it is redundant from the caller.
 191          */
 192         printk(KERN_WARNING "pdc202xx_new: %s channel reset.\n",
 193                 drive->hwif->channel ? "Secondary" : "Primary");
 194 }
 195 
 196 /**
 197  * read_counter - Read the byte count registers
 198  * @dma_base: for the port address
 199  */
 200 static long read_counter(u32 dma_base)
 201 {
 202         u32  pri_dma_base = dma_base, sec_dma_base = dma_base + 0x08;
 203         u8   cnt0, cnt1, cnt2, cnt3;
 204         long count = 0, last;
 205         int  retry = 3;
 206 
 207         do {
 208                 last = count;
 209 
 210                 /* Read the current count */
 211                 outb(0x20, pri_dma_base + 0x01);
 212                 cnt0 = inb(pri_dma_base + 0x03);
 213                 outb(0x21, pri_dma_base + 0x01);
 214                 cnt1 = inb(pri_dma_base + 0x03);
 215                 outb(0x20, sec_dma_base + 0x01);
 216                 cnt2 = inb(sec_dma_base + 0x03);
 217                 outb(0x21, sec_dma_base + 0x01);
 218                 cnt3 = inb(sec_dma_base + 0x03);
 219 
 220                 count = (cnt3 << 23) | (cnt2 << 15) | (cnt1 << 8) | cnt0;
 221 
 222                 /*
 223                  * The 30-bit decrementing counter is read in 4 pieces.
 224                  * Incorrect value may be read when the most significant bytes
 225                  * are changing...
 226                  */
 227         } while (retry-- && (((last ^ count) & 0x3fff8000) || last < count));
 228 
 229         DBG("cnt0[%02X] cnt1[%02X] cnt2[%02X] cnt3[%02X]\n",
 230                   cnt0, cnt1, cnt2, cnt3);
 231 
 232         return count;
 233 }
 234 
 235 /**
 236  * detect_pll_input_clock - Detect the PLL input clock in Hz.
 237  * @dma_base: for the port address
 238  * E.g. 16949000 on 33 MHz PCI bus, i.e. half of the PCI clock.
 239  */
 240 static long detect_pll_input_clock(unsigned long dma_base)
 241 {
 242         ktime_t start_time, end_time;
 243         long start_count, end_count;
 244         long pll_input, usec_elapsed;
 245         u8 scr1;
 246 
 247         start_count = read_counter(dma_base);
 248         start_time = ktime_get();
 249 
 250         /* Start the test mode */
 251         outb(0x01, dma_base + 0x01);
 252         scr1 = inb(dma_base + 0x03);
 253         DBG("scr1[%02X]\n", scr1);
 254         outb(scr1 | 0x40, dma_base + 0x03);
 255 
 256         /* Let the counter run for 10 ms. */
 257         mdelay(10);
 258 
 259         end_count = read_counter(dma_base);
 260         end_time = ktime_get();
 261 
 262         /* Stop the test mode */
 263         outb(0x01, dma_base + 0x01);
 264         scr1 = inb(dma_base + 0x03);
 265         DBG("scr1[%02X]\n", scr1);
 266         outb(scr1 & ~0x40, dma_base + 0x03);
 267 
 268         /*
 269          * Calculate the input clock in Hz
 270          * (the clock counter is 30 bit wide and counts down)
 271          */
 272         usec_elapsed = ktime_us_delta(end_time, start_time);
 273         pll_input = ((start_count - end_count) & 0x3fffffff) / 10 *
 274                 (10000000 / usec_elapsed);
 275 
 276         DBG("start[%ld] end[%ld]\n", start_count, end_count);
 277 
 278         return pll_input;
 279 }
 280 
 281 #ifdef CONFIG_PPC_PMAC
 282 static void apple_kiwi_init(struct pci_dev *pdev)
 283 {
 284         struct device_node *np = pci_device_to_OF_node(pdev);
 285         u8 conf;
 286 
 287         if (np == NULL || !of_device_is_compatible(np, "kiwi-root"))
 288                 return;
 289 
 290         if (pdev->revision >= 0x03) {
 291                 /* Setup chip magic config stuff (from darwin) */
 292                 pci_read_config_byte (pdev, 0x40, &conf);
 293                 pci_write_config_byte(pdev, 0x40, (conf | 0x01));
 294         }
 295 }
 296 #endif /* CONFIG_PPC_PMAC */
 297 
 298 static int init_chipset_pdcnew(struct pci_dev *dev)
 299 {
 300         const char *name = DRV_NAME;
 301         unsigned long dma_base = pci_resource_start(dev, 4);
 302         unsigned long sec_dma_base = dma_base + 0x08;
 303         long pll_input, pll_output, ratio;
 304         int f, r;
 305         u8 pll_ctl0, pll_ctl1;
 306 
 307         if (dma_base == 0)
 308                 return -EFAULT;
 309 
 310 #ifdef CONFIG_PPC_PMAC
 311         apple_kiwi_init(dev);
 312 #endif
 313 
 314         /* Calculate the required PLL output frequency */
 315         switch(max_dma_rate(dev)) {
 316                 case 4: /* it's 133 MHz for Ultra133 chips */
 317                         pll_output = 133333333;
 318                         break;
 319                 case 3: /* and  100 MHz for Ultra100 chips */
 320                 default:
 321                         pll_output = 100000000;
 322                         break;
 323         }
 324 
 325         /*
 326          * Detect PLL input clock.
 327          * On some systems, where PCI bus is running at non-standard clock rate
 328          * (e.g. 25 or 40 MHz), we have to adjust the cycle time.
 329          * PDC20268 and newer chips employ PLL circuit to help correct timing
 330          * registers setting.
 331          */
 332         pll_input = detect_pll_input_clock(dma_base);
 333         printk(KERN_INFO "%s %s: PLL input clock is %ld kHz\n",
 334                 name, pci_name(dev), pll_input / 1000);
 335 
 336         /* Sanity check */
 337         if (unlikely(pll_input < 5000000L || pll_input > 70000000L)) {
 338                 printk(KERN_ERR "%s %s: Bad PLL input clock %ld Hz, giving up!"
 339                         "\n", name, pci_name(dev), pll_input);
 340                 goto out;
 341         }
 342 
 343 #ifdef DEBUG
 344         DBG("pll_output is %ld Hz\n", pll_output);
 345 
 346         /* Show the current clock value of PLL control register
 347          * (maybe already configured by the BIOS)
 348          */
 349         outb(0x02, sec_dma_base + 0x01);
 350         pll_ctl0 = inb(sec_dma_base + 0x03);
 351         outb(0x03, sec_dma_base + 0x01);
 352         pll_ctl1 = inb(sec_dma_base + 0x03);
 353 
 354         DBG("pll_ctl[%02X][%02X]\n", pll_ctl0, pll_ctl1);
 355 #endif
 356 
 357         /*
 358          * Calculate the ratio of F, R and NO
 359          * POUT = (F + 2) / (( R + 2) * NO)
 360          */
 361         ratio = pll_output / (pll_input / 1000);
 362         if (ratio < 8600L) { /* 8.6x */
 363                 /* Using NO = 0x01, R = 0x0d */
 364                 r = 0x0d;
 365         } else if (ratio < 12900L) { /* 12.9x */
 366                 /* Using NO = 0x01, R = 0x08 */
 367                 r = 0x08;
 368         } else if (ratio < 16100L) { /* 16.1x */
 369                 /* Using NO = 0x01, R = 0x06 */
 370                 r = 0x06;
 371         } else if (ratio < 64000L) { /* 64x */
 372                 r = 0x00;
 373         } else {
 374                 /* Invalid ratio */
 375                 printk(KERN_ERR "%s %s: Bad ratio %ld, giving up!\n",
 376                         name, pci_name(dev), ratio);
 377                 goto out;
 378         }
 379 
 380         f = (ratio * (r + 2)) / 1000 - 2;
 381 
 382         DBG("F[%d] R[%d] ratio*1000[%ld]\n", f, r, ratio);
 383 
 384         if (unlikely(f < 0 || f > 127)) {
 385                 /* Invalid F */
 386                 printk(KERN_ERR "%s %s: F[%d] invalid!\n",
 387                         name, pci_name(dev), f);
 388                 goto out;
 389         }
 390 
 391         pll_ctl0 = (u8) f;
 392         pll_ctl1 = (u8) r;
 393 
 394         DBG("Writing pll_ctl[%02X][%02X]\n", pll_ctl0, pll_ctl1);
 395 
 396         outb(0x02,     sec_dma_base + 0x01);
 397         outb(pll_ctl0, sec_dma_base + 0x03);
 398         outb(0x03,     sec_dma_base + 0x01);
 399         outb(pll_ctl1, sec_dma_base + 0x03);
 400 
 401         /* Wait the PLL circuit to be stable */
 402         mdelay(30);
 403 
 404 #ifdef DEBUG
 405         /*
 406          *  Show the current clock value of PLL control register
 407          */
 408         outb(0x02, sec_dma_base + 0x01);
 409         pll_ctl0 = inb(sec_dma_base + 0x03);
 410         outb(0x03, sec_dma_base + 0x01);
 411         pll_ctl1 = inb(sec_dma_base + 0x03);
 412 
 413         DBG("pll_ctl[%02X][%02X]\n", pll_ctl0, pll_ctl1);
 414 #endif
 415 
 416  out:
 417         return 0;
 418 }
 419 
 420 static struct pci_dev *pdc20270_get_dev2(struct pci_dev *dev)
 421 {
 422         struct pci_dev *dev2;
 423 
 424         dev2 = pci_get_slot(dev->bus, PCI_DEVFN(PCI_SLOT(dev->devfn) + 1,
 425                                                 PCI_FUNC(dev->devfn)));
 426 
 427         if (dev2 &&
 428             dev2->vendor == dev->vendor &&
 429             dev2->device == dev->device) {
 430 
 431                 if (dev2->irq != dev->irq) {
 432                         dev2->irq = dev->irq;
 433                         printk(KERN_INFO DRV_NAME " %s: PCI config space "
 434                                 "interrupt fixed\n", pci_name(dev));
 435                 }
 436 
 437                 return dev2;
 438         }
 439 
 440         return NULL;
 441 }
 442 
 443 static const struct ide_port_ops pdcnew_port_ops = {
 444         .set_pio_mode           = pdcnew_set_pio_mode,
 445         .set_dma_mode           = pdcnew_set_dma_mode,
 446         .resetproc              = pdcnew_reset,
 447         .cable_detect           = pdcnew_cable_detect,
 448 };
 449 
 450 #define DECLARE_PDCNEW_DEV(udma) \
 451         { \
 452                 .name           = DRV_NAME, \
 453                 .init_chipset   = init_chipset_pdcnew, \
 454                 .port_ops       = &pdcnew_port_ops, \
 455                 .host_flags     = IDE_HFLAG_POST_SET_MODE | \
 456                                   IDE_HFLAG_ERROR_STOPS_FIFO | \
 457                                   IDE_HFLAG_OFF_BOARD, \
 458                 .pio_mask       = ATA_PIO4, \
 459                 .mwdma_mask     = ATA_MWDMA2, \
 460                 .udma_mask      = udma, \
 461         }
 462 
 463 static const struct ide_port_info pdcnew_chipsets[] = {
 464         /* 0: PDC202{68,70} */          DECLARE_PDCNEW_DEV(ATA_UDMA5),
 465         /* 1: PDC202{69,71,75,76,77} */ DECLARE_PDCNEW_DEV(ATA_UDMA6),
 466 };
 467 
 468 /**
 469  *      pdc202new_init_one      -       called when a pdc202xx is found
 470  *      @dev: the pdc202new device
 471  *      @id: the matching pci id
 472  *
 473  *      Called when the PCI registration layer (or the IDE initialization)
 474  *      finds a device matching our IDE device tables.
 475  */
 476  
 477 static int pdc202new_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 478 {
 479         const struct ide_port_info *d = &pdcnew_chipsets[id->driver_data];
 480         struct pci_dev *bridge = dev->bus->self;
 481 
 482         if (dev->device == PCI_DEVICE_ID_PROMISE_20270 && bridge &&
 483             bridge->vendor == PCI_VENDOR_ID_DEC &&
 484             bridge->device == PCI_DEVICE_ID_DEC_21150) {
 485                 struct pci_dev *dev2;
 486 
 487                 if (PCI_SLOT(dev->devfn) & 2)
 488                         return -ENODEV;
 489 
 490                 dev2 = pdc20270_get_dev2(dev);
 491 
 492                 if (dev2) {
 493                         int ret = ide_pci_init_two(dev, dev2, d, NULL);
 494                         if (ret < 0)
 495                                 pci_dev_put(dev2);
 496                         return ret;
 497                 }
 498         }
 499 
 500         if (dev->device == PCI_DEVICE_ID_PROMISE_20276 && bridge &&
 501             bridge->vendor == PCI_VENDOR_ID_INTEL &&
 502             (bridge->device == PCI_DEVICE_ID_INTEL_I960 ||
 503              bridge->device == PCI_DEVICE_ID_INTEL_I960RM)) {
 504                 printk(KERN_INFO DRV_NAME " %s: attached to I2O RAID controller,"
 505                         " skipping\n", pci_name(dev));
 506                 return -ENODEV;
 507         }
 508 
 509         return ide_pci_init_one(dev, d, NULL);
 510 }
 511 
 512 static void pdc202new_remove(struct pci_dev *dev)
 513 {
 514         struct ide_host *host = pci_get_drvdata(dev);
 515         struct pci_dev *dev2 = host->dev[1] ? to_pci_dev(host->dev[1]) : NULL;
 516 
 517         ide_pci_remove(dev);
 518         pci_dev_put(dev2);
 519 }
 520 
 521 static const struct pci_device_id pdc202new_pci_tbl[] = {
 522         { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20268), 0 },
 523         { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20269), 1 },
 524         { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20270), 0 },
 525         { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20271), 1 },
 526         { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20275), 1 },
 527         { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20276), 1 },
 528         { PCI_VDEVICE(PROMISE, PCI_DEVICE_ID_PROMISE_20277), 1 },
 529         { 0, },
 530 };
 531 MODULE_DEVICE_TABLE(pci, pdc202new_pci_tbl);
 532 
 533 static struct pci_driver pdc202new_pci_driver = {
 534         .name           = "Promise_IDE",
 535         .id_table       = pdc202new_pci_tbl,
 536         .probe          = pdc202new_init_one,
 537         .remove         = pdc202new_remove,
 538         .suspend        = ide_pci_suspend,
 539         .resume         = ide_pci_resume,
 540 };
 541 
 542 static int __init pdc202new_ide_init(void)
 543 {
 544         return ide_pci_register_driver(&pdc202new_pci_driver);
 545 }
 546 
 547 static void __exit pdc202new_ide_exit(void)
 548 {
 549         pci_unregister_driver(&pdc202new_pci_driver);
 550 }
 551 
 552 module_init(pdc202new_ide_init);
 553 module_exit(pdc202new_ide_exit);
 554 
 555 MODULE_AUTHOR("Andre Hedrick, Frank Tiernan");
 556 MODULE_DESCRIPTION("PCI driver module for Promise PDC20268 and higher");
 557 MODULE_LICENSE("GPL");
/* [<][>][^][v][top][bottom][index][help] */
root/drivers/ide/pdc202xx_new.c

DEFINITIONS
