drivers/staging/rtl8723bs/include/hal_pwr

/* [<][>][^][v][top][bottom][index][help] */
   1 /* SPDX-License-Identifier: GPL-2.0 */
   2 #ifndef REALTEK_POWER_SEQUENCE_8723B
   3 #define REALTEK_POWER_SEQUENCE_8723B
   4 
   5 #include "HalPwrSeqCmd.h"
   6 
   7 /*
   8         Check document WM-20130815-JackieLau-RTL8723B_Power_Architecture v08.vsd
   9         There are 6 HW Power States:
  10         0: POFF--Power Off
  11         1: PDN--Power Down
  12         2: CARDEMU--Card Emulation
  13         3: ACT--Active Mode
  14         4: LPS--Low Power State
  15         5: SUS--Suspend
  16 
  17         The transision from different states are defined below
  18         TRANS_CARDEMU_TO_ACT
  19         TRANS_ACT_TO_CARDEMU
  20         TRANS_CARDEMU_TO_SUS
  21         TRANS_SUS_TO_CARDEMU
  22         TRANS_CARDEMU_TO_PDN
  23         TRANS_ACT_TO_LPS
  24         TRANS_LPS_TO_ACT
  25 
  26         TRANS_END
  27 */
  28 #define RTL8723B_TRANS_CARDEMU_TO_ACT_STEPS     26
  29 #define RTL8723B_TRANS_ACT_TO_CARDEMU_STEPS     15
  30 #define RTL8723B_TRANS_CARDEMU_TO_SUS_STEPS     15
  31 #define RTL8723B_TRANS_SUS_TO_CARDEMU_STEPS     15
  32 #define RTL8723B_TRANS_CARDEMU_TO_PDN_STEPS     15
  33 #define RTL8723B_TRANS_PDN_TO_CARDEMU_STEPS     15
  34 #define RTL8723B_TRANS_ACT_TO_LPS_STEPS         15
  35 #define RTL8723B_TRANS_LPS_TO_ACT_STEPS         15
  36 #define RTL8723B_TRANS_ACT_TO_SWLPS_STEPS               22
  37 #define RTL8723B_TRANS_SWLPS_TO_ACT_STEPS               15
  38 #define RTL8723B_TRANS_END_STEPS                1
  39 
  40 
  41 #define RTL8723B_TRANS_CARDEMU_TO_ACT                                                                                                           \
  42         /* format */                                                                                                                            \
  43         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value },  comments here*/                                                           \
  44         {0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0}, /*0x20[0] = 1b'1 enable LDOA12 MACRO block for all interface*/   \
  45         {0x0067, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, 0}, /*0x67[0] = 0 to disable BT_GPS_SEL pins*/    \
  46         {0x0001, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 1, PWRSEQ_DELAY_MS},/*Delay 1ms*/   \
  47         {0x0000, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT5, 0}, /*0x00[5] = 1b'0 release analog Ips to digital , 1:isolation*/   \
  48         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, (BIT4|BIT3|BIT2), 0},/* disable SW LPS 0x04[10]= 0 and WLSUS_EN 0x04[11]= 0*/     \
  49         {0x0075, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0 , BIT0},/* Disable USB suspend */    \
  50         {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT1, BIT1},/* wait till 0x04[17] = 1    power ready*/  \
  51         {0x0075, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0 , 0},/* Enable USB suspend */        \
  52         {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0},/* release WLON reset  0x04[16]= 1*/  \
  53         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, 0},/* disable HWPDN 0x04[15]= 0*/   \
  54         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, (BIT4|BIT3), 0},/* disable WL suspend*/   \
  55         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0},/* polling until return 0*/   \
  56         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT0, 0},/**/   \
  57         {0x0010, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT6, BIT6},/* Enable WL control XTAL setting*/   \
  58         {0x0049, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1},/*Enable falling edge triggering interrupt*/\
  59         {0x0063, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1},/*Enable GPIO9 interrupt mode*/\
  60         {0x0062, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0},/*Enable GPIO9 input mode*/\
  61         {0x0058, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0},/*Enable HSISR GPIO[C:0] interrupt*/\
  62         {0x005A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1},/*Enable HSISR GPIO9 interrupt*/\
  63         {0x0068, PWR_CUT_TESTCHIP_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3, BIT3},/*For GPIO9 internal pull high setting by test chip*/\
  64         {0x0069, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT6, BIT6},/*For GPIO9 internal pull high setting*/\
  65 
  66 
  67 #define RTL8723B_TRANS_ACT_TO_CARDEMU                                                                                                   \
  68         /* format */                                                                                                                            \
  69         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value },  comments here*/                                                           \
  70         {0x001F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0},/*0x1F[7:0] = 0 turn off RF*/    \
  71         {0x0049, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0},/*Enable rising edge triggering interrupt*/ \
  72         {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0},/* release WLON reset  0x04[16]= 1*/  \
  73         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1}, /*0x04[9] = 1 turn off MAC by HW state machine*/     \
  74         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT1, 0}, /*wait till 0x04[9] = 0 polling until return 0 to disable*/   \
  75         {0x0010, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT6, 0},/* Enable BT control XTAL setting*/\
  76         {0x0000, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT5, BIT5}, /*0x00[5] = 1b'1 analog Ips to digital , 1:isolation*/   \
  77         {0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0}, /*0x20[0] = 1b'0 disable LDOA12 MACRO block*/\
  78 
  79 
  80 #define RTL8723B_TRANS_CARDEMU_TO_SUS                                                                                                   \
  81         /* format */                                                                                                                            \
  82         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value },  comments here*/                                                           \
  83         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4|BIT3, (BIT4|BIT3)}, /*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/       \
  84         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3|BIT4, BIT3}, /*0x04[12:11] = 2b'01 enable WL suspend*/     \
  85         {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, BIT4}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/   \
  86         {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07[7:0] = 0x20 SDIO SOP option to disable BG/MB/ACK/SWR*/   \
  87         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3|BIT4, BIT3|BIT4}, /*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/ \
  88         {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT0, BIT0}, /*Set SDIO suspend local register*/        \
  89         {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT1, 0}, /*wait power state to suspend*/
  90 
  91 #define RTL8723B_TRANS_SUS_TO_CARDEMU                                                                                                   \
  92         /* format */                                                                                                                            \
  93         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value },  comments here*/                                                           \
  94         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3 | BIT7, 0}, /*clear suspend enable and power down enable*/   \
  95         {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT0, 0}, /*Set SDIO suspend local register*/   \
  96         {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT1, BIT1}, /*wait power state to suspend*/\
  97         {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, 0}, /*0x23[4] = 1b'0 12H LDO enter normal mode*/   \
  98         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3|BIT4, 0}, /*0x04[12:11] = 2b'01enable WL suspend*/
  99 
 100 #define RTL8723B_TRANS_CARDEMU_TO_CARDDIS                                                                                                       \
 101         /* format */                                                                                                                            \
 102         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, omments here*/                                                             \
 103         {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07 = 0x20 , SOP option to disable BG/MB*/       \
 104         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3|BIT4, BIT3}, /*0x04[12:11] = 2b'01 enable WL suspend*/     \
 105         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT2, BIT2}, /*0x04[10] = 1, enable SW LPS*/      \
 106         {0x004A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 1}, /*0x48[16] = 1 to enable GPIO9 as EXT WAKEUP*/   \
 107         {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, BIT4}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/   \
 108         {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT0, BIT0}, /*Set SDIO suspend local register*/        \
 109         {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT1, 0}, /*wait power state to suspend*/
 110 
 111 #define RTL8723B_TRANS_CARDDIS_TO_CARDEMU                                                                                                       \
 112         /* format */                                                                                                                            \
 113         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, comments here*/                                                            \
 114         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3 | BIT7, 0}, /*clear suspend enable and power down enable*/   \
 115         {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT0, 0}, /*Set SDIO suspend local register*/   \
 116         {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT1, BIT1}, /*wait power state to suspend*/\
 117         {0x004A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0}, /*0x48[16] = 0 to disable GPIO9 as EXT WAKEUP*/   \
 118         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3|BIT4, 0}, /*0x04[12:11] = 2b'01enable WL suspend*/\
 119         {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, 0}, /*0x23[4] = 1b'0 12H LDO enter normal mode*/   \
 120         {0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0},/*PCIe DMA start*/
 121 
 122 
 123 #define RTL8723B_TRANS_CARDEMU_TO_PDN                                                                                           \
 124         /* format */                                                                                                                            \
 125         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, comments here*/                                                            \
 126         {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, BIT4}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/   \
 127         {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK|PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07[7:0] = 0x20 SOP option to disable BG/MB/ACK/SWR*/   \
 128         {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0},/* 0x04[16] = 0*/\
 129         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, BIT7},/* 0x04[15] = 1*/
 130 
 131 #define RTL8723B_TRANS_PDN_TO_CARDEMU                                                                                           \
 132         /* format */                                                                                                                            \
 133         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, comments here*/                                                            \
 134         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, 0},/* 0x04[15] = 0*/
 135 
 136 #define RTL8723B_TRANS_ACT_TO_LPS                                                                                                               \
 137         /* format */                                                                                                                            \
 138         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, comments here*/                                                            \
 139         {0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF},/*PCIe DMA stop*/     \
 140         {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF},/*Tx Pause*/  \
 141         {0x05F8, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/        \
 142         {0x05F9, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/        \
 143         {0x05FA, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/        \
 144         {0x05FB, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/        \
 145         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0},/*CCK and OFDM are disabled, and clock are gated*/       \
 146         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US},/*Delay 1us*/ \
 147         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0},/*Whole BB is reset*/    \
 148         {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x03},/*Reset MAC TRX*/     \
 149         {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0},/*check if removed later*/       \
 150         {0x0093, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x00},/*When driver enter Sus/ Disable, enable LOP for BT*/        \
 151         {0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT5, BIT5},/*Respond TxOK to scheduler*/ \
 152 
 153 
 154 #define RTL8723B_TRANS_LPS_TO_ACT                                                                                                                       \
 155         /* format */                                                                                                                            \
 156         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, comments here*/                                                            \
 157         {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, 0xFF, 0x84}, /*SDIO RPWM*/\
 158         {0xFE58, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x84}, /*USB RPWM*/\
 159         {0x0361, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x84}, /*PCIe RPWM*/\
 160         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS}, /*Delay*/\
 161         {0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, 0}, /*.     0x08[4] = 0              switch TSF to 40M*/\
 162         {0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT7, 0}, /*Polling 0x109[7]= 0  TSF in 40M*/\
 163         {0x0029, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT6|BIT7, 0}, /*.        0x29[7:6] = 2b'00        enable BB clock*/\
 164         {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1}, /*.  0x101[1] = 1*/\
 165         {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF}, /*.  0x100[7:0] = 0xFF        enable WMAC TRX*/\
 166         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1|BIT0, BIT1|BIT0}, /*.        0x02[1:0] = 2b'11        enable BB macro*/\
 167         {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0}, /*.     0x522 = 0*/
 168 
 169 
 170  #define RTL8723B_TRANS_ACT_TO_SWLPS                                                                                                            \
 171         /* format */                                                                                                                            \
 172         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, comments here*/                                                            \
 173         {0x0194, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0},/*enable 32 K source*/       \
 174         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0},/*CCK and OFDM are disabled, and clock are gated*/      \
 175         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 1},/*CCK and OFDM are enable*/     \
 176         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0},/*CCK and OFDM are disabled, and clock are gated*/      \
 177         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 1},/*CCK and OFDM are enable*/     \
 178         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0},/*CCK and OFDM are disabled, and clock are gated*/      \
 179         {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x3F},/*Reset MAC TRX*/    \
 180         {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0},/*disable security engine*/     \
 181         {0x0093, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x40},/*When driver enter Sus/ Disable, enable LOP for BT*/        \
 182         {0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT5, BIT5},/*reset dual TSF*/   \
 183         {0x0003, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT2, 0},/*Reset CPU*/   \
 184         {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0},/*Reset MCUFWDL register*/      \
 185         {0x001D, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0},/*Reset CPU IO Wrapper*/        \
 186         {0x001D, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 1},/*Reset CPU IO Wrapper*/        \
 187         {0x0287, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*polling RXFF packet number = 0 */   \
 188         {0x0286, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT1, BIT1},/*polling RXDMA idle */    \
 189         {0x013D, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0},/*Clear FW RPWM interrupt */\
 190         {0x0139, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0},/*Set FW RPWM interrupt source*/\
 191         {0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, BIT4},/*switch TSF to 32K*/\
 192         {0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, BIT7},/*polling TSF stable*/\
 193         {0x0090, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0},/*Set FW LPS*/       \
 194         {0x0090, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT0, 0},/*polling FW LPS ready */
 195 
 196 
 197 #define RTL8723B_TRANS_SWLPS_TO_ACT                                                                                                                     \
 198         /* format */                                                                                                                            \
 199         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, comments here*/                                                            \
 200         {0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, 0},/*switch TSF to 32K*/\
 201         {0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, 0},/*polling TSF stable*/\
 202         {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1}, /*. 0x101[1] = 1, enable security engine*/\
 203         {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF}, /*. 0x100[7:0] = 0xFF        enable WMAC TRX*/\
 204         {0x06B7, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x09}, /*. reset MAC rx state machine*/\
 205         {0x06B4, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x86}, /*. reset MAC rx state machine*/\
 206         {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1},/* set CPU RAM code ready*/  \
 207         {0x001D, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0},/*Reset CPU IO Wrapper*/        \
 208         {0x0003, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT2, 0},/* Enable CPU*/ \
 209         {0x001D, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0},/*enable CPU IO Wrapper*/    \
 210         {0x0003, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT2, BIT2},/* Enable CPU*/      \
 211         {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT7, BIT7},/*polling FW init ready */ \
 212         {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT6, BIT6},/*polling FW init ready */ \
 213         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0}, /*. 0x02[1:0] = 2b'11        enable BB macro*/\
 214         {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0}, /*.    0x522 = 0*/
 215 
 216 #define RTL8723B_TRANS_END                                                                                                                      \
 217         /* format */                                                                                                                            \
 218         /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, comments here*/                                                            \
 219         {0xFFFF, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, 0, PWR_CMD_END, 0, 0}, 
 220 
 221 
 222 extern WLAN_PWR_CFG rtl8723B_power_on_flow[RTL8723B_TRANS_CARDEMU_TO_ACT_STEPS+RTL8723B_TRANS_END_STEPS];
 223 extern WLAN_PWR_CFG rtl8723B_radio_off_flow[RTL8723B_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723B_TRANS_END_STEPS];
 224 extern WLAN_PWR_CFG rtl8723B_card_disable_flow[RTL8723B_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723B_TRANS_CARDEMU_TO_PDN_STEPS+RTL8723B_TRANS_END_STEPS];
 225 extern WLAN_PWR_CFG rtl8723B_card_enable_flow[RTL8723B_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723B_TRANS_CARDEMU_TO_PDN_STEPS+RTL8723B_TRANS_END_STEPS];
 226 extern WLAN_PWR_CFG rtl8723B_suspend_flow[RTL8723B_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723B_TRANS_CARDEMU_TO_SUS_STEPS+RTL8723B_TRANS_END_STEPS];
 227 extern WLAN_PWR_CFG rtl8723B_resume_flow[RTL8723B_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723B_TRANS_CARDEMU_TO_SUS_STEPS+RTL8723B_TRANS_END_STEPS];
 228 extern WLAN_PWR_CFG rtl8723B_hwpdn_flow[RTL8723B_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723B_TRANS_CARDEMU_TO_PDN_STEPS+RTL8723B_TRANS_END_STEPS];
 229 extern WLAN_PWR_CFG rtl8723B_enter_lps_flow[RTL8723B_TRANS_ACT_TO_LPS_STEPS+RTL8723B_TRANS_END_STEPS];
 230 extern WLAN_PWR_CFG rtl8723B_leave_lps_flow[RTL8723B_TRANS_LPS_TO_ACT_STEPS+RTL8723B_TRANS_END_STEPS];
 231 extern WLAN_PWR_CFG rtl8723B_enter_swlps_flow[RTL8723B_TRANS_ACT_TO_SWLPS_STEPS+RTL8723B_TRANS_END_STEPS];
 232 extern WLAN_PWR_CFG rtl8723B_leave_swlps_flow[RTL8723B_TRANS_SWLPS_TO_ACT_STEPS+RTL8723B_TRANS_END_STEPS];
 233 #endif
/* [<][>][^][v][top][bottom][index][help] */
root/drivers/staging/rtl8723bs/include/hal_pwr_seq.h

INCLUDED FROM
