root/drivers/staging/media/soc_camera/soc_ov9740.c

/* [<][>][^][v][top][bottom][index][help] */

DEFINITIONS

This source file includes following definitions.
  1. ov9740_reg_read
  2. ov9740_reg_write
  3. ov9740_reg_rmw
  4. ov9740_reg_write_array
  5. ov9740_s_stream
  6. ov9740_res_roundup
  7. ov9740_set_res
  8. ov9740_s_fmt
  9. ov9740_set_fmt
  10. ov9740_enum_mbus_code
  11. ov9740_get_selection
  12. ov9740_s_ctrl
  13. ov9740_s_power
  14. ov9740_get_register
  15. ov9740_set_register
  16. ov9740_video_probe
  17. ov9740_g_mbus_config
  18. ov9740_probe
  19. ov9740_remove

   1 // SPDX-License-Identifier: GPL-2.0
   2 /*
   3  * OmniVision OV9740 Camera Driver
   4  *
   5  * Copyright (C) 2011 NVIDIA Corporation
   6  *
   7  * Based on ov9640 camera driver.
   8  */
   9 #include <linux/init.h>
  10 #include <linux/module.h>
  11 #include <linux/i2c.h>
  12 #include <linux/slab.h>
  13 #include <linux/v4l2-mediabus.h>
  14 
  15 #include <media/soc_camera.h>
  16 #include <media/v4l2-clk.h>
  17 #include <media/v4l2-ctrls.h>
  18 
  19 #define to_ov9740(sd)           container_of(sd, struct ov9740_priv, subdev)
  20 
  21 /* General Status Registers */
  22 #define OV9740_MODEL_ID_HI              0x0000
  23 #define OV9740_MODEL_ID_LO              0x0001
  24 #define OV9740_REVISION_NUMBER          0x0002
  25 #define OV9740_MANUFACTURER_ID          0x0003
  26 #define OV9740_SMIA_VERSION             0x0004
  27 
  28 /* General Setup Registers */
  29 #define OV9740_MODE_SELECT              0x0100
  30 #define OV9740_IMAGE_ORT                0x0101
  31 #define OV9740_SOFTWARE_RESET           0x0103
  32 #define OV9740_GRP_PARAM_HOLD           0x0104
  33 #define OV9740_MSK_CORRUP_FM            0x0105
  34 
  35 /* Timing Setting */
  36 #define OV9740_FRM_LENGTH_LN_HI         0x0340 /* VTS */
  37 #define OV9740_FRM_LENGTH_LN_LO         0x0341 /* VTS */
  38 #define OV9740_LN_LENGTH_PCK_HI         0x0342 /* HTS */
  39 #define OV9740_LN_LENGTH_PCK_LO         0x0343 /* HTS */
  40 #define OV9740_X_ADDR_START_HI          0x0344
  41 #define OV9740_X_ADDR_START_LO          0x0345
  42 #define OV9740_Y_ADDR_START_HI          0x0346
  43 #define OV9740_Y_ADDR_START_LO          0x0347
  44 #define OV9740_X_ADDR_END_HI            0x0348
  45 #define OV9740_X_ADDR_END_LO            0x0349
  46 #define OV9740_Y_ADDR_END_HI            0x034a
  47 #define OV9740_Y_ADDR_END_LO            0x034b
  48 #define OV9740_X_OUTPUT_SIZE_HI         0x034c
  49 #define OV9740_X_OUTPUT_SIZE_LO         0x034d
  50 #define OV9740_Y_OUTPUT_SIZE_HI         0x034e
  51 #define OV9740_Y_OUTPUT_SIZE_LO         0x034f
  52 
  53 /* IO Control Registers */
  54 #define OV9740_IO_CREL00                0x3002
  55 #define OV9740_IO_CREL01                0x3004
  56 #define OV9740_IO_CREL02                0x3005
  57 #define OV9740_IO_OUTPUT_SEL01          0x3026
  58 #define OV9740_IO_OUTPUT_SEL02          0x3027
  59 
  60 /* AWB Registers */
  61 #define OV9740_AWB_MANUAL_CTRL          0x3406
  62 
  63 /* Analog Control Registers */
  64 #define OV9740_ANALOG_CTRL01            0x3601
  65 #define OV9740_ANALOG_CTRL02            0x3602
  66 #define OV9740_ANALOG_CTRL03            0x3603
  67 #define OV9740_ANALOG_CTRL04            0x3604
  68 #define OV9740_ANALOG_CTRL10            0x3610
  69 #define OV9740_ANALOG_CTRL12            0x3612
  70 #define OV9740_ANALOG_CTRL15            0x3615
  71 #define OV9740_ANALOG_CTRL20            0x3620
  72 #define OV9740_ANALOG_CTRL21            0x3621
  73 #define OV9740_ANALOG_CTRL22            0x3622
  74 #define OV9740_ANALOG_CTRL30            0x3630
  75 #define OV9740_ANALOG_CTRL31            0x3631
  76 #define OV9740_ANALOG_CTRL32            0x3632
  77 #define OV9740_ANALOG_CTRL33            0x3633
  78 
  79 /* Sensor Control */
  80 #define OV9740_SENSOR_CTRL03            0x3703
  81 #define OV9740_SENSOR_CTRL04            0x3704
  82 #define OV9740_SENSOR_CTRL05            0x3705
  83 #define OV9740_SENSOR_CTRL07            0x3707
  84 
  85 /* Timing Control */
  86 #define OV9740_TIMING_CTRL17            0x3817
  87 #define OV9740_TIMING_CTRL19            0x3819
  88 #define OV9740_TIMING_CTRL33            0x3833
  89 #define OV9740_TIMING_CTRL35            0x3835
  90 
  91 /* Banding Filter */
  92 #define OV9740_AEC_MAXEXPO_60_H         0x3a02
  93 #define OV9740_AEC_MAXEXPO_60_L         0x3a03
  94 #define OV9740_AEC_B50_STEP_HI          0x3a08
  95 #define OV9740_AEC_B50_STEP_LO          0x3a09
  96 #define OV9740_AEC_B60_STEP_HI          0x3a0a
  97 #define OV9740_AEC_B60_STEP_LO          0x3a0b
  98 #define OV9740_AEC_CTRL0D               0x3a0d
  99 #define OV9740_AEC_CTRL0E               0x3a0e
 100 #define OV9740_AEC_MAXEXPO_50_H         0x3a14
 101 #define OV9740_AEC_MAXEXPO_50_L         0x3a15
 102 
 103 /* AEC/AGC Control */
 104 #define OV9740_AEC_ENABLE               0x3503
 105 #define OV9740_GAIN_CEILING_01          0x3a18
 106 #define OV9740_GAIN_CEILING_02          0x3a19
 107 #define OV9740_AEC_HI_THRESHOLD         0x3a11
 108 #define OV9740_AEC_3A1A                 0x3a1a
 109 #define OV9740_AEC_CTRL1B_WPT2          0x3a1b
 110 #define OV9740_AEC_CTRL0F_WPT           0x3a0f
 111 #define OV9740_AEC_CTRL10_BPT           0x3a10
 112 #define OV9740_AEC_CTRL1E_BPT2          0x3a1e
 113 #define OV9740_AEC_LO_THRESHOLD         0x3a1f
 114 
 115 /* BLC Control */
 116 #define OV9740_BLC_AUTO_ENABLE          0x4002
 117 #define OV9740_BLC_MODE                 0x4005
 118 
 119 /* VFIFO */
 120 #define OV9740_VFIFO_READ_START_HI      0x4608
 121 #define OV9740_VFIFO_READ_START_LO      0x4609
 122 
 123 /* DVP Control */
 124 #define OV9740_DVP_VSYNC_CTRL02         0x4702
 125 #define OV9740_DVP_VSYNC_MODE           0x4704
 126 #define OV9740_DVP_VSYNC_CTRL06         0x4706
 127 
 128 /* PLL Setting */
 129 #define OV9740_PLL_MODE_CTRL01          0x3104
 130 #define OV9740_PRE_PLL_CLK_DIV          0x0305
 131 #define OV9740_PLL_MULTIPLIER           0x0307
 132 #define OV9740_VT_SYS_CLK_DIV           0x0303
 133 #define OV9740_VT_PIX_CLK_DIV           0x0301
 134 #define OV9740_PLL_CTRL3010             0x3010
 135 #define OV9740_VFIFO_CTRL00             0x460e
 136 
 137 /* ISP Control */
 138 #define OV9740_ISP_CTRL00               0x5000
 139 #define OV9740_ISP_CTRL01               0x5001
 140 #define OV9740_ISP_CTRL03               0x5003
 141 #define OV9740_ISP_CTRL05               0x5005
 142 #define OV9740_ISP_CTRL12               0x5012
 143 #define OV9740_ISP_CTRL19               0x5019
 144 #define OV9740_ISP_CTRL1A               0x501a
 145 #define OV9740_ISP_CTRL1E               0x501e
 146 #define OV9740_ISP_CTRL1F               0x501f
 147 #define OV9740_ISP_CTRL20               0x5020
 148 #define OV9740_ISP_CTRL21               0x5021
 149 
 150 /* AWB */
 151 #define OV9740_AWB_CTRL00               0x5180
 152 #define OV9740_AWB_CTRL01               0x5181
 153 #define OV9740_AWB_CTRL02               0x5182
 154 #define OV9740_AWB_CTRL03               0x5183
 155 #define OV9740_AWB_ADV_CTRL01           0x5184
 156 #define OV9740_AWB_ADV_CTRL02           0x5185
 157 #define OV9740_AWB_ADV_CTRL03           0x5186
 158 #define OV9740_AWB_ADV_CTRL04           0x5187
 159 #define OV9740_AWB_ADV_CTRL05           0x5188
 160 #define OV9740_AWB_ADV_CTRL06           0x5189
 161 #define OV9740_AWB_ADV_CTRL07           0x518a
 162 #define OV9740_AWB_ADV_CTRL08           0x518b
 163 #define OV9740_AWB_ADV_CTRL09           0x518c
 164 #define OV9740_AWB_ADV_CTRL10           0x518d
 165 #define OV9740_AWB_ADV_CTRL11           0x518e
 166 #define OV9740_AWB_CTRL0F               0x518f
 167 #define OV9740_AWB_CTRL10               0x5190
 168 #define OV9740_AWB_CTRL11               0x5191
 169 #define OV9740_AWB_CTRL12               0x5192
 170 #define OV9740_AWB_CTRL13               0x5193
 171 #define OV9740_AWB_CTRL14               0x5194
 172 
 173 /* MIPI Control */
 174 #define OV9740_MIPI_CTRL00              0x4800
 175 #define OV9740_MIPI_3837                0x3837
 176 #define OV9740_MIPI_CTRL01              0x4801
 177 #define OV9740_MIPI_CTRL03              0x4803
 178 #define OV9740_MIPI_CTRL05              0x4805
 179 #define OV9740_VFIFO_RD_CTRL            0x4601
 180 #define OV9740_MIPI_CTRL_3012           0x3012
 181 #define OV9740_SC_CMMM_MIPI_CTR         0x3014
 182 
 183 #define OV9740_MAX_WIDTH                1280
 184 #define OV9740_MAX_HEIGHT               720
 185 
 186 /* Misc. structures */
 187 struct ov9740_reg {
 188         u16                             reg;
 189         u8                              val;
 190 };
 191 
 192 struct ov9740_priv {
 193         struct v4l2_subdev              subdev;
 194         struct v4l2_ctrl_handler        hdl;
 195         struct v4l2_clk                 *clk;
 196 
 197         u16                             model;
 198         u8                              revision;
 199         u8                              manid;
 200         u8                              smiaver;
 201 
 202         bool                            flag_vflip;
 203         bool                            flag_hflip;
 204 
 205         /* For suspend/resume. */
 206         struct v4l2_mbus_framefmt       current_mf;
 207         bool                            current_enable;
 208 };
 209 
 210 static const struct ov9740_reg ov9740_defaults[] = {
 211         /* Software Reset */
 212         { OV9740_SOFTWARE_RESET,        0x01 },
 213 
 214         /* Banding Filter */
 215         { OV9740_AEC_B50_STEP_HI,       0x00 },
 216         { OV9740_AEC_B50_STEP_LO,       0xe8 },
 217         { OV9740_AEC_CTRL0E,            0x03 },
 218         { OV9740_AEC_MAXEXPO_50_H,      0x15 },
 219         { OV9740_AEC_MAXEXPO_50_L,      0xc6 },
 220         { OV9740_AEC_B60_STEP_HI,       0x00 },
 221         { OV9740_AEC_B60_STEP_LO,       0xc0 },
 222         { OV9740_AEC_CTRL0D,            0x04 },
 223         { OV9740_AEC_MAXEXPO_60_H,      0x18 },
 224         { OV9740_AEC_MAXEXPO_60_L,      0x20 },
 225 
 226         /* LC */
 227         { 0x5842, 0x02 }, { 0x5843, 0x5e }, { 0x5844, 0x04 }, { 0x5845, 0x32 },
 228         { 0x5846, 0x03 }, { 0x5847, 0x29 }, { 0x5848, 0x02 }, { 0x5849, 0xcc },
 229 
 230         /* Un-documented OV9740 registers */
 231         { 0x5800, 0x29 }, { 0x5801, 0x25 }, { 0x5802, 0x20 }, { 0x5803, 0x21 },
 232         { 0x5804, 0x26 }, { 0x5805, 0x2e }, { 0x5806, 0x11 }, { 0x5807, 0x0c },
 233         { 0x5808, 0x09 }, { 0x5809, 0x0a }, { 0x580a, 0x0e }, { 0x580b, 0x16 },
 234         { 0x580c, 0x06 }, { 0x580d, 0x02 }, { 0x580e, 0x00 }, { 0x580f, 0x00 },
 235         { 0x5810, 0x04 }, { 0x5811, 0x0a }, { 0x5812, 0x05 }, { 0x5813, 0x02 },
 236         { 0x5814, 0x00 }, { 0x5815, 0x00 }, { 0x5816, 0x03 }, { 0x5817, 0x09 },
 237         { 0x5818, 0x0f }, { 0x5819, 0x0a }, { 0x581a, 0x07 }, { 0x581b, 0x08 },
 238         { 0x581c, 0x0b }, { 0x581d, 0x14 }, { 0x581e, 0x28 }, { 0x581f, 0x23 },
 239         { 0x5820, 0x1d }, { 0x5821, 0x1e }, { 0x5822, 0x24 }, { 0x5823, 0x2a },
 240         { 0x5824, 0x4f }, { 0x5825, 0x6f }, { 0x5826, 0x5f }, { 0x5827, 0x7f },
 241         { 0x5828, 0x9f }, { 0x5829, 0x5f }, { 0x582a, 0x8f }, { 0x582b, 0x9e },
 242         { 0x582c, 0x8f }, { 0x582d, 0x9f }, { 0x582e, 0x4f }, { 0x582f, 0x87 },
 243         { 0x5830, 0x86 }, { 0x5831, 0x97 }, { 0x5832, 0xae }, { 0x5833, 0x3f },
 244         { 0x5834, 0x8e }, { 0x5835, 0x7c }, { 0x5836, 0x7e }, { 0x5837, 0xaf },
 245         { 0x5838, 0x8f }, { 0x5839, 0x8f }, { 0x583a, 0x9f }, { 0x583b, 0x7f },
 246         { 0x583c, 0x5f },
 247 
 248         /* Y Gamma */
 249         { 0x5480, 0x07 }, { 0x5481, 0x18 }, { 0x5482, 0x2c }, { 0x5483, 0x4e },
 250         { 0x5484, 0x5e }, { 0x5485, 0x6b }, { 0x5486, 0x77 }, { 0x5487, 0x82 },
 251         { 0x5488, 0x8c }, { 0x5489, 0x95 }, { 0x548a, 0xa4 }, { 0x548b, 0xb1 },
 252         { 0x548c, 0xc6 }, { 0x548d, 0xd8 }, { 0x548e, 0xe9 },
 253 
 254         /* UV Gamma */
 255         { 0x5490, 0x0f }, { 0x5491, 0xff }, { 0x5492, 0x0d }, { 0x5493, 0x05 },
 256         { 0x5494, 0x07 }, { 0x5495, 0x1a }, { 0x5496, 0x04 }, { 0x5497, 0x01 },
 257         { 0x5498, 0x03 }, { 0x5499, 0x53 }, { 0x549a, 0x02 }, { 0x549b, 0xeb },
 258         { 0x549c, 0x02 }, { 0x549d, 0xa0 }, { 0x549e, 0x02 }, { 0x549f, 0x67 },
 259         { 0x54a0, 0x02 }, { 0x54a1, 0x3b }, { 0x54a2, 0x02 }, { 0x54a3, 0x18 },
 260         { 0x54a4, 0x01 }, { 0x54a5, 0xe7 }, { 0x54a6, 0x01 }, { 0x54a7, 0xc3 },
 261         { 0x54a8, 0x01 }, { 0x54a9, 0x94 }, { 0x54aa, 0x01 }, { 0x54ab, 0x72 },
 262         { 0x54ac, 0x01 }, { 0x54ad, 0x57 },
 263 
 264         /* AWB */
 265         { OV9740_AWB_CTRL00,            0xf0 },
 266         { OV9740_AWB_CTRL01,            0x00 },
 267         { OV9740_AWB_CTRL02,            0x41 },
 268         { OV9740_AWB_CTRL03,            0x42 },
 269         { OV9740_AWB_ADV_CTRL01,        0x8a },
 270         { OV9740_AWB_ADV_CTRL02,        0x61 },
 271         { OV9740_AWB_ADV_CTRL03,        0xce },
 272         { OV9740_AWB_ADV_CTRL04,        0xa8 },
 273         { OV9740_AWB_ADV_CTRL05,        0x17 },
 274         { OV9740_AWB_ADV_CTRL06,        0x1f },
 275         { OV9740_AWB_ADV_CTRL07,        0x27 },
 276         { OV9740_AWB_ADV_CTRL08,        0x41 },
 277         { OV9740_AWB_ADV_CTRL09,        0x34 },
 278         { OV9740_AWB_ADV_CTRL10,        0xf0 },
 279         { OV9740_AWB_ADV_CTRL11,        0x10 },
 280         { OV9740_AWB_CTRL0F,            0xff },
 281         { OV9740_AWB_CTRL10,            0x00 },
 282         { OV9740_AWB_CTRL11,            0xff },
 283         { OV9740_AWB_CTRL12,            0x00 },
 284         { OV9740_AWB_CTRL13,            0xff },
 285         { OV9740_AWB_CTRL14,            0x00 },
 286 
 287         /* CIP */
 288         { 0x530d, 0x12 },
 289 
 290         /* CMX */
 291         { 0x5380, 0x01 }, { 0x5381, 0x00 }, { 0x5382, 0x00 }, { 0x5383, 0x17 },
 292         { 0x5384, 0x00 }, { 0x5385, 0x01 }, { 0x5386, 0x00 }, { 0x5387, 0x00 },
 293         { 0x5388, 0x00 }, { 0x5389, 0xe0 }, { 0x538a, 0x00 }, { 0x538b, 0x20 },
 294         { 0x538c, 0x00 }, { 0x538d, 0x00 }, { 0x538e, 0x00 }, { 0x538f, 0x16 },
 295         { 0x5390, 0x00 }, { 0x5391, 0x9c }, { 0x5392, 0x00 }, { 0x5393, 0xa0 },
 296         { 0x5394, 0x18 },
 297 
 298         /* 50/60 Detection */
 299         { 0x3c0a, 0x9c }, { 0x3c0b, 0x3f },
 300 
 301         /* Output Select */
 302         { OV9740_IO_OUTPUT_SEL01,       0x00 },
 303         { OV9740_IO_OUTPUT_SEL02,       0x00 },
 304         { OV9740_IO_CREL00,             0x00 },
 305         { OV9740_IO_CREL01,             0x00 },
 306         { OV9740_IO_CREL02,             0x00 },
 307 
 308         /* AWB Control */
 309         { OV9740_AWB_MANUAL_CTRL,       0x00 },
 310 
 311         /* Analog Control */
 312         { OV9740_ANALOG_CTRL03,         0xaa },
 313         { OV9740_ANALOG_CTRL32,         0x2f },
 314         { OV9740_ANALOG_CTRL20,         0x66 },
 315         { OV9740_ANALOG_CTRL21,         0xc0 },
 316         { OV9740_ANALOG_CTRL31,         0x52 },
 317         { OV9740_ANALOG_CTRL33,         0x50 },
 318         { OV9740_ANALOG_CTRL30,         0xca },
 319         { OV9740_ANALOG_CTRL04,         0x0c },
 320         { OV9740_ANALOG_CTRL01,         0x40 },
 321         { OV9740_ANALOG_CTRL02,         0x16 },
 322         { OV9740_ANALOG_CTRL10,         0xa1 },
 323         { OV9740_ANALOG_CTRL12,         0x24 },
 324         { OV9740_ANALOG_CTRL22,         0x9f },
 325         { OV9740_ANALOG_CTRL15,         0xf0 },
 326 
 327         /* Sensor Control */
 328         { OV9740_SENSOR_CTRL03,         0x42 },
 329         { OV9740_SENSOR_CTRL04,         0x10 },
 330         { OV9740_SENSOR_CTRL05,         0x45 },
 331         { OV9740_SENSOR_CTRL07,         0x14 },
 332 
 333         /* Timing Control */
 334         { OV9740_TIMING_CTRL33,         0x04 },
 335         { OV9740_TIMING_CTRL35,         0x02 },
 336         { OV9740_TIMING_CTRL19,         0x6e },
 337         { OV9740_TIMING_CTRL17,         0x94 },
 338 
 339         /* AEC/AGC Control */
 340         { OV9740_AEC_ENABLE,            0x10 },
 341         { OV9740_GAIN_CEILING_01,       0x00 },
 342         { OV9740_GAIN_CEILING_02,       0x7f },
 343         { OV9740_AEC_HI_THRESHOLD,      0xa0 },
 344         { OV9740_AEC_3A1A,              0x05 },
 345         { OV9740_AEC_CTRL1B_WPT2,       0x50 },
 346         { OV9740_AEC_CTRL0F_WPT,        0x50 },
 347         { OV9740_AEC_CTRL10_BPT,        0x4c },
 348         { OV9740_AEC_CTRL1E_BPT2,       0x4c },
 349         { OV9740_AEC_LO_THRESHOLD,      0x26 },
 350 
 351         /* BLC Control */
 352         { OV9740_BLC_AUTO_ENABLE,       0x45 },
 353         { OV9740_BLC_MODE,              0x18 },
 354 
 355         /* DVP Control */
 356         { OV9740_DVP_VSYNC_CTRL02,      0x04 },
 357         { OV9740_DVP_VSYNC_MODE,        0x00 },
 358         { OV9740_DVP_VSYNC_CTRL06,      0x08 },
 359 
 360         /* PLL Setting */
 361         { OV9740_PLL_MODE_CTRL01,       0x20 },
 362         { OV9740_PRE_PLL_CLK_DIV,       0x03 },
 363         { OV9740_PLL_MULTIPLIER,        0x4c },
 364         { OV9740_VT_SYS_CLK_DIV,        0x01 },
 365         { OV9740_VT_PIX_CLK_DIV,        0x08 },
 366         { OV9740_PLL_CTRL3010,          0x01 },
 367         { OV9740_VFIFO_CTRL00,          0x82 },
 368 
 369         /* Timing Setting */
 370         /* VTS */
 371         { OV9740_FRM_LENGTH_LN_HI,      0x03 },
 372         { OV9740_FRM_LENGTH_LN_LO,      0x07 },
 373         /* HTS */
 374         { OV9740_LN_LENGTH_PCK_HI,      0x06 },
 375         { OV9740_LN_LENGTH_PCK_LO,      0x62 },
 376 
 377         /* MIPI Control */
 378         { OV9740_MIPI_CTRL00,           0x44 }, /* 0x64 for discontinuous clk */
 379         { OV9740_MIPI_3837,             0x01 },
 380         { OV9740_MIPI_CTRL01,           0x0f },
 381         { OV9740_MIPI_CTRL03,           0x05 },
 382         { OV9740_MIPI_CTRL05,           0x10 },
 383         { OV9740_VFIFO_RD_CTRL,         0x16 },
 384         { OV9740_MIPI_CTRL_3012,        0x70 },
 385         { OV9740_SC_CMMM_MIPI_CTR,      0x01 },
 386 
 387         /* YUYV order */
 388         { OV9740_ISP_CTRL19,            0x02 },
 389 };
 390 
 391 static u32 ov9740_codes[] = {
 392         MEDIA_BUS_FMT_YUYV8_2X8,
 393 };
 394 
 395 /* read a register */
 396 static int ov9740_reg_read(struct i2c_client *client, u16 reg, u8 *val)
 397 {
 398         int ret;
 399         struct i2c_msg msg[] = {
 400                 {
 401                         .addr   = client->addr,
 402                         .flags  = 0,
 403                         .len    = 2,
 404                         .buf    = (u8 *)&reg,
 405                 },
 406                 {
 407                         .addr   = client->addr,
 408                         .flags  = I2C_M_RD,
 409                         .len    = 1,
 410                         .buf    = val,
 411                 },
 412         };
 413 
 414         reg = swab16(reg);
 415 
 416         ret = i2c_transfer(client->adapter, msg, 2);
 417         if (ret < 0) {
 418                 dev_err(&client->dev, "Failed reading register 0x%04x!\n", reg);
 419                 return ret;
 420         }
 421 
 422         return 0;
 423 }
 424 
 425 /* write a register */
 426 static int ov9740_reg_write(struct i2c_client *client, u16 reg, u8 val)
 427 {
 428         struct i2c_msg msg;
 429         struct {
 430                 u16 reg;
 431                 u8 val;
 432         } __packed buf;
 433         int ret;
 434 
 435         reg = swab16(reg);
 436 
 437         buf.reg = reg;
 438         buf.val = val;
 439 
 440         msg.addr        = client->addr;
 441         msg.flags       = 0;
 442         msg.len         = 3;
 443         msg.buf         = (u8 *)&buf;
 444 
 445         ret = i2c_transfer(client->adapter, &msg, 1);
 446         if (ret < 0) {
 447                 dev_err(&client->dev, "Failed writing register 0x%04x!\n", reg);
 448                 return ret;
 449         }
 450 
 451         return 0;
 452 }
 453 
 454 
 455 /* Read a register, alter its bits, write it back */
 456 static int ov9740_reg_rmw(struct i2c_client *client, u16 reg, u8 set, u8 unset)
 457 {
 458         u8 val;
 459         int ret;
 460 
 461         ret = ov9740_reg_read(client, reg, &val);
 462         if (ret < 0) {
 463                 dev_err(&client->dev,
 464                         "[Read]-Modify-Write of register 0x%04x failed!\n",
 465                         reg);
 466                 return ret;
 467         }
 468 
 469         val |= set;
 470         val &= ~unset;
 471 
 472         ret = ov9740_reg_write(client, reg, val);
 473         if (ret < 0) {
 474                 dev_err(&client->dev,
 475                         "Read-Modify-[Write] of register 0x%04x failed!\n",
 476                         reg);
 477                 return ret;
 478         }
 479 
 480         return 0;
 481 }
 482 
 483 static int ov9740_reg_write_array(struct i2c_client *client,
 484                                   const struct ov9740_reg *regarray,
 485                                   int regarraylen)
 486 {
 487         int i;
 488         int ret;
 489 
 490         for (i = 0; i < regarraylen; i++) {
 491                 ret = ov9740_reg_write(client,
 492                                        regarray[i].reg, regarray[i].val);
 493                 if (ret < 0)
 494                         return ret;
 495         }
 496 
 497         return 0;
 498 }
 499 
 500 /* Start/Stop streaming from the device */
 501 static int ov9740_s_stream(struct v4l2_subdev *sd, int enable)
 502 {
 503         struct i2c_client *client = v4l2_get_subdevdata(sd);
 504         struct ov9740_priv *priv = to_ov9740(sd);
 505         int ret;
 506 
 507         /* Program orientation register. */
 508         if (priv->flag_vflip)
 509                 ret = ov9740_reg_rmw(client, OV9740_IMAGE_ORT, 0x2, 0);
 510         else
 511                 ret = ov9740_reg_rmw(client, OV9740_IMAGE_ORT, 0, 0x2);
 512         if (ret < 0)
 513                 return ret;
 514 
 515         if (priv->flag_hflip)
 516                 ret = ov9740_reg_rmw(client, OV9740_IMAGE_ORT, 0x1, 0);
 517         else
 518                 ret = ov9740_reg_rmw(client, OV9740_IMAGE_ORT, 0, 0x1);
 519         if (ret < 0)
 520                 return ret;
 521 
 522         if (enable) {
 523                 dev_dbg(&client->dev, "Enabling Streaming\n");
 524                 /* Start Streaming */
 525                 ret = ov9740_reg_write(client, OV9740_MODE_SELECT, 0x01);
 526 
 527         } else {
 528                 dev_dbg(&client->dev, "Disabling Streaming\n");
 529                 /* Software Reset */
 530                 ret = ov9740_reg_write(client, OV9740_SOFTWARE_RESET, 0x01);
 531                 if (!ret)
 532                         /* Setting Streaming to Standby */
 533                         ret = ov9740_reg_write(client, OV9740_MODE_SELECT,
 534                                                0x00);
 535         }
 536 
 537         priv->current_enable = enable;
 538 
 539         return ret;
 540 }
 541 
 542 /* select nearest higher resolution for capture */
 543 static void ov9740_res_roundup(u32 *width, u32 *height)
 544 {
 545         /* Width must be a multiple of 4 pixels. */
 546         *width = ALIGN(*width, 4);
 547 
 548         /* Max resolution is 1280x720 (720p). */
 549         if (*width > OV9740_MAX_WIDTH)
 550                 *width = OV9740_MAX_WIDTH;
 551 
 552         if (*height > OV9740_MAX_HEIGHT)
 553                 *height = OV9740_MAX_HEIGHT;
 554 }
 555 
 556 /* Setup registers according to resolution and color encoding */
 557 static int ov9740_set_res(struct i2c_client *client, u32 width, u32 height)
 558 {
 559         u32 x_start;
 560         u32 y_start;
 561         u32 x_end;
 562         u32 y_end;
 563         bool scaling = false;
 564         u32 scale_input_x;
 565         u32 scale_input_y;
 566         int ret;
 567 
 568         if ((width != OV9740_MAX_WIDTH) || (height != OV9740_MAX_HEIGHT))
 569                 scaling = true;
 570 
 571         /*
 572          * Try to use as much of the sensor area as possible when supporting
 573          * smaller resolutions.  Depending on the aspect ratio of the
 574          * chosen resolution, we can either use the full width of the sensor,
 575          * or the full height of the sensor (or both if the aspect ratio is
 576          * the same as 1280x720.
 577          */
 578         if ((OV9740_MAX_WIDTH * height) > (OV9740_MAX_HEIGHT * width)) {
 579                 scale_input_x = (OV9740_MAX_HEIGHT * width) / height;
 580                 scale_input_y = OV9740_MAX_HEIGHT;
 581         } else {
 582                 scale_input_x = OV9740_MAX_WIDTH;
 583                 scale_input_y = (OV9740_MAX_WIDTH * height) / width;
 584         }
 585 
 586         /* These describe the area of the sensor to use. */
 587         x_start = (OV9740_MAX_WIDTH - scale_input_x) / 2;
 588         y_start = (OV9740_MAX_HEIGHT - scale_input_y) / 2;
 589         x_end = x_start + scale_input_x - 1;
 590         y_end = y_start + scale_input_y - 1;
 591 
 592         ret = ov9740_reg_write(client, OV9740_X_ADDR_START_HI, x_start >> 8);
 593         if (ret)
 594                 goto done;
 595         ret = ov9740_reg_write(client, OV9740_X_ADDR_START_LO, x_start & 0xff);
 596         if (ret)
 597                 goto done;
 598         ret = ov9740_reg_write(client, OV9740_Y_ADDR_START_HI, y_start >> 8);
 599         if (ret)
 600                 goto done;
 601         ret = ov9740_reg_write(client, OV9740_Y_ADDR_START_LO, y_start & 0xff);
 602         if (ret)
 603                 goto done;
 604 
 605         ret = ov9740_reg_write(client, OV9740_X_ADDR_END_HI, x_end >> 8);
 606         if (ret)
 607                 goto done;
 608         ret = ov9740_reg_write(client, OV9740_X_ADDR_END_LO, x_end & 0xff);
 609         if (ret)
 610                 goto done;
 611         ret = ov9740_reg_write(client, OV9740_Y_ADDR_END_HI, y_end >> 8);
 612         if (ret)
 613                 goto done;
 614         ret = ov9740_reg_write(client, OV9740_Y_ADDR_END_LO, y_end & 0xff);
 615         if (ret)
 616                 goto done;
 617 
 618         ret = ov9740_reg_write(client, OV9740_X_OUTPUT_SIZE_HI, width >> 8);
 619         if (ret)
 620                 goto done;
 621         ret = ov9740_reg_write(client, OV9740_X_OUTPUT_SIZE_LO, width & 0xff);
 622         if (ret)
 623                 goto done;
 624         ret = ov9740_reg_write(client, OV9740_Y_OUTPUT_SIZE_HI, height >> 8);
 625         if (ret)
 626                 goto done;
 627         ret = ov9740_reg_write(client, OV9740_Y_OUTPUT_SIZE_LO, height & 0xff);
 628         if (ret)
 629                 goto done;
 630 
 631         ret = ov9740_reg_write(client, OV9740_ISP_CTRL1E, scale_input_x >> 8);
 632         if (ret)
 633                 goto done;
 634         ret = ov9740_reg_write(client, OV9740_ISP_CTRL1F, scale_input_x & 0xff);
 635         if (ret)
 636                 goto done;
 637         ret = ov9740_reg_write(client, OV9740_ISP_CTRL20, scale_input_y >> 8);
 638         if (ret)
 639                 goto done;
 640         ret = ov9740_reg_write(client, OV9740_ISP_CTRL21, scale_input_y & 0xff);
 641         if (ret)
 642                 goto done;
 643 
 644         ret = ov9740_reg_write(client, OV9740_VFIFO_READ_START_HI,
 645                                (scale_input_x - width) >> 8);
 646         if (ret)
 647                 goto done;
 648         ret = ov9740_reg_write(client, OV9740_VFIFO_READ_START_LO,
 649                                (scale_input_x - width) & 0xff);
 650         if (ret)
 651                 goto done;
 652 
 653         ret = ov9740_reg_write(client, OV9740_ISP_CTRL00, 0xff);
 654         if (ret)
 655                 goto done;
 656         ret = ov9740_reg_write(client, OV9740_ISP_CTRL01, 0xef |
 657                                                           (scaling << 4));
 658         if (ret)
 659                 goto done;
 660         ret = ov9740_reg_write(client, OV9740_ISP_CTRL03, 0xff);
 661 
 662 done:
 663         return ret;
 664 }
 665 
 666 /* set the format we will capture in */
 667 static int ov9740_s_fmt(struct v4l2_subdev *sd,
 668                         struct v4l2_mbus_framefmt *mf)
 669 {
 670         struct i2c_client *client = v4l2_get_subdevdata(sd);
 671         struct ov9740_priv *priv = to_ov9740(sd);
 672         int ret;
 673 
 674         ret = ov9740_reg_write_array(client, ov9740_defaults,
 675                                      ARRAY_SIZE(ov9740_defaults));
 676         if (ret < 0)
 677                 return ret;
 678 
 679         ret = ov9740_set_res(client, mf->width, mf->height);
 680         if (ret < 0)
 681                 return ret;
 682 
 683         priv->current_mf = *mf;
 684         return ret;
 685 }
 686 
 687 static int ov9740_set_fmt(struct v4l2_subdev *sd,
 688                 struct v4l2_subdev_pad_config *cfg,
 689                 struct v4l2_subdev_format *format)
 690 {
 691         struct v4l2_mbus_framefmt *mf = &format->format;
 692 
 693         if (format->pad)
 694                 return -EINVAL;
 695 
 696         ov9740_res_roundup(&mf->width, &mf->height);
 697 
 698         mf->field = V4L2_FIELD_NONE;
 699         mf->code = MEDIA_BUS_FMT_YUYV8_2X8;
 700         mf->colorspace = V4L2_COLORSPACE_SRGB;
 701 
 702         if (format->which == V4L2_SUBDEV_FORMAT_ACTIVE)
 703                 return ov9740_s_fmt(sd, mf);
 704         cfg->try_fmt = *mf;
 705         return 0;
 706 }
 707 
 708 static int ov9740_enum_mbus_code(struct v4l2_subdev *sd,
 709                 struct v4l2_subdev_pad_config *cfg,
 710                 struct v4l2_subdev_mbus_code_enum *code)
 711 {
 712         if (code->pad || code->index >= ARRAY_SIZE(ov9740_codes))
 713                 return -EINVAL;
 714 
 715         code->code = ov9740_codes[code->index];
 716 
 717         return 0;
 718 }
 719 
 720 static int ov9740_get_selection(struct v4l2_subdev *sd,
 721                 struct v4l2_subdev_pad_config *cfg,
 722                 struct v4l2_subdev_selection *sel)
 723 {
 724         if (sel->which != V4L2_SUBDEV_FORMAT_ACTIVE)
 725                 return -EINVAL;
 726 
 727         switch (sel->target) {
 728         case V4L2_SEL_TGT_CROP_BOUNDS:
 729         case V4L2_SEL_TGT_CROP:
 730                 sel->r.left = 0;
 731                 sel->r.top = 0;
 732                 sel->r.width = OV9740_MAX_WIDTH;
 733                 sel->r.height = OV9740_MAX_HEIGHT;
 734                 return 0;
 735         default:
 736                 return -EINVAL;
 737         }
 738 }
 739 
 740 /* Set status of additional camera capabilities */
 741 static int ov9740_s_ctrl(struct v4l2_ctrl *ctrl)
 742 {
 743         struct ov9740_priv *priv =
 744                 container_of(ctrl->handler, struct ov9740_priv, hdl);
 745 
 746         switch (ctrl->id) {
 747         case V4L2_CID_VFLIP:
 748                 priv->flag_vflip = ctrl->val;
 749                 break;
 750         case V4L2_CID_HFLIP:
 751                 priv->flag_hflip = ctrl->val;
 752                 break;
 753         default:
 754                 return -EINVAL;
 755         }
 756 
 757         return 0;
 758 }
 759 
 760 static int ov9740_s_power(struct v4l2_subdev *sd, int on)
 761 {
 762         struct i2c_client *client = v4l2_get_subdevdata(sd);
 763         struct soc_camera_subdev_desc *ssdd = soc_camera_i2c_to_desc(client);
 764         struct ov9740_priv *priv = to_ov9740(sd);
 765         int ret;
 766 
 767         if (on) {
 768                 ret = soc_camera_power_on(&client->dev, ssdd, priv->clk);
 769                 if (ret < 0)
 770                         return ret;
 771 
 772                 if (priv->current_enable) {
 773                         ov9740_s_fmt(sd, &priv->current_mf);
 774                         ov9740_s_stream(sd, 1);
 775                 }
 776         } else {
 777                 if (priv->current_enable) {
 778                         ov9740_s_stream(sd, 0);
 779                         priv->current_enable = true;
 780                 }
 781 
 782                 soc_camera_power_off(&client->dev, ssdd, priv->clk);
 783         }
 784 
 785         return 0;
 786 }
 787 
 788 #ifdef CONFIG_VIDEO_ADV_DEBUG
 789 static int ov9740_get_register(struct v4l2_subdev *sd,
 790                                struct v4l2_dbg_register *reg)
 791 {
 792         struct i2c_client *client = v4l2_get_subdevdata(sd);
 793         int ret;
 794         u8 val;
 795 
 796         if (reg->reg & ~0xffff)
 797                 return -EINVAL;
 798 
 799         reg->size = 2;
 800 
 801         ret = ov9740_reg_read(client, reg->reg, &val);
 802         if (ret)
 803                 return ret;
 804 
 805         reg->val = (__u64)val;
 806 
 807         return ret;
 808 }
 809 
 810 static int ov9740_set_register(struct v4l2_subdev *sd,
 811                                const struct v4l2_dbg_register *reg)
 812 {
 813         struct i2c_client *client = v4l2_get_subdevdata(sd);
 814 
 815         if (reg->reg & ~0xffff || reg->val & ~0xff)
 816                 return -EINVAL;
 817 
 818         return ov9740_reg_write(client, reg->reg, reg->val);
 819 }
 820 #endif
 821 
 822 static int ov9740_video_probe(struct i2c_client *client)
 823 {
 824         struct v4l2_subdev *sd = i2c_get_clientdata(client);
 825         struct ov9740_priv *priv = to_ov9740(sd);
 826         u8 modelhi, modello;
 827         int ret;
 828 
 829         ret = ov9740_s_power(&priv->subdev, 1);
 830         if (ret < 0)
 831                 return ret;
 832 
 833         /*
 834          * check and show product ID and manufacturer ID
 835          */
 836         ret = ov9740_reg_read(client, OV9740_MODEL_ID_HI, &modelhi);
 837         if (ret < 0)
 838                 goto done;
 839 
 840         ret = ov9740_reg_read(client, OV9740_MODEL_ID_LO, &modello);
 841         if (ret < 0)
 842                 goto done;
 843 
 844         priv->model = (modelhi << 8) | modello;
 845 
 846         ret = ov9740_reg_read(client, OV9740_REVISION_NUMBER, &priv->revision);
 847         if (ret < 0)
 848                 goto done;
 849 
 850         ret = ov9740_reg_read(client, OV9740_MANUFACTURER_ID, &priv->manid);
 851         if (ret < 0)
 852                 goto done;
 853 
 854         ret = ov9740_reg_read(client, OV9740_SMIA_VERSION, &priv->smiaver);
 855         if (ret < 0)
 856                 goto done;
 857 
 858         if (priv->model != 0x9740) {
 859                 ret = -ENODEV;
 860                 goto done;
 861         }
 862 
 863         dev_info(&client->dev, "ov9740 Model ID 0x%04x, Revision 0x%02x, Manufacturer 0x%02x, SMIA Version 0x%02x\n",
 864                  priv->model, priv->revision, priv->manid, priv->smiaver);
 865 
 866         ret = v4l2_ctrl_handler_setup(&priv->hdl);
 867 
 868 done:
 869         ov9740_s_power(&priv->subdev, 0);
 870         return ret;
 871 }
 872 
 873 /* Request bus settings on camera side */
 874 static int ov9740_g_mbus_config(struct v4l2_subdev *sd,
 875                                 struct v4l2_mbus_config *cfg)
 876 {
 877         struct i2c_client *client = v4l2_get_subdevdata(sd);
 878         struct soc_camera_subdev_desc *ssdd = soc_camera_i2c_to_desc(client);
 879 
 880         cfg->flags = V4L2_MBUS_PCLK_SAMPLE_RISING | V4L2_MBUS_MASTER |
 881                 V4L2_MBUS_VSYNC_ACTIVE_HIGH | V4L2_MBUS_HSYNC_ACTIVE_HIGH |
 882                 V4L2_MBUS_DATA_ACTIVE_HIGH;
 883         cfg->type = V4L2_MBUS_PARALLEL;
 884         cfg->flags = soc_camera_apply_board_flags(ssdd, cfg);
 885 
 886         return 0;
 887 }
 888 
 889 static const struct v4l2_subdev_video_ops ov9740_video_ops = {
 890         .s_stream       = ov9740_s_stream,
 891         .g_mbus_config  = ov9740_g_mbus_config,
 892 };
 893 
 894 static const struct v4l2_subdev_core_ops ov9740_core_ops = {
 895         .s_power                = ov9740_s_power,
 896 #ifdef CONFIG_VIDEO_ADV_DEBUG
 897         .g_register             = ov9740_get_register,
 898         .s_register             = ov9740_set_register,
 899 #endif
 900 };
 901 
 902 static const struct v4l2_subdev_pad_ops ov9740_pad_ops = {
 903         .enum_mbus_code = ov9740_enum_mbus_code,
 904         .get_selection  = ov9740_get_selection,
 905         .set_fmt        = ov9740_set_fmt,
 906 };
 907 
 908 static const struct v4l2_subdev_ops ov9740_subdev_ops = {
 909         .core   = &ov9740_core_ops,
 910         .video  = &ov9740_video_ops,
 911         .pad    = &ov9740_pad_ops,
 912 };
 913 
 914 static const struct v4l2_ctrl_ops ov9740_ctrl_ops = {
 915         .s_ctrl = ov9740_s_ctrl,
 916 };
 917 
 918 /*
 919  * i2c_driver function
 920  */
 921 static int ov9740_probe(struct i2c_client *client,
 922                         const struct i2c_device_id *did)
 923 {
 924         struct ov9740_priv *priv;
 925         struct soc_camera_subdev_desc *ssdd = soc_camera_i2c_to_desc(client);
 926         int ret;
 927 
 928         if (!ssdd) {
 929                 dev_err(&client->dev, "Missing platform_data for driver\n");
 930                 return -EINVAL;
 931         }
 932 
 933         priv = devm_kzalloc(&client->dev, sizeof(*priv), GFP_KERNEL);
 934         if (!priv)
 935                 return -ENOMEM;
 936 
 937         v4l2_i2c_subdev_init(&priv->subdev, client, &ov9740_subdev_ops);
 938         v4l2_ctrl_handler_init(&priv->hdl, 13);
 939         v4l2_ctrl_new_std(&priv->hdl, &ov9740_ctrl_ops,
 940                         V4L2_CID_VFLIP, 0, 1, 1, 0);
 941         v4l2_ctrl_new_std(&priv->hdl, &ov9740_ctrl_ops,
 942                         V4L2_CID_HFLIP, 0, 1, 1, 0);
 943         priv->subdev.ctrl_handler = &priv->hdl;
 944         if (priv->hdl.error)
 945                 return priv->hdl.error;
 946 
 947         priv->clk = v4l2_clk_get(&client->dev, "mclk");
 948         if (IS_ERR(priv->clk)) {
 949                 ret = PTR_ERR(priv->clk);
 950                 goto eclkget;
 951         }
 952 
 953         ret = ov9740_video_probe(client);
 954         if (ret < 0) {
 955                 v4l2_clk_put(priv->clk);
 956 eclkget:
 957                 v4l2_ctrl_handler_free(&priv->hdl);
 958         }
 959 
 960         return ret;
 961 }
 962 
 963 static int ov9740_remove(struct i2c_client *client)
 964 {
 965         struct ov9740_priv *priv = i2c_get_clientdata(client);
 966 
 967         v4l2_clk_put(priv->clk);
 968         v4l2_device_unregister_subdev(&priv->subdev);
 969         v4l2_ctrl_handler_free(&priv->hdl);
 970         return 0;
 971 }
 972 
 973 static const struct i2c_device_id ov9740_id[] = {
 974         { "ov9740", 0 },
 975         { }
 976 };
 977 MODULE_DEVICE_TABLE(i2c, ov9740_id);
 978 
 979 static struct i2c_driver ov9740_i2c_driver = {
 980         .driver = {
 981                 .name = "ov9740",
 982         },
 983         .probe    = ov9740_probe,
 984         .remove   = ov9740_remove,
 985         .id_table = ov9740_id,
 986 };
 987 
 988 module_i2c_driver(ov9740_i2c_driver);
 989 
 990 MODULE_DESCRIPTION("SoC Camera driver for OmniVision OV9740");
 991 MODULE_AUTHOR("Andrew Chew <achew@nvidia.com>");
 992 MODULE_LICENSE("GPL v2");

/* [<][>][^][v][top][bottom][index][help] */