drivers/atm/ambassador.h

/* [<][>][^][v][top][bottom][index][help] */
   1 /* SPDX-License-Identifier: GPL-2.0-or-later */
   2 /*
   3   Madge Ambassador ATM Adapter driver.
   4   Copyright (C) 1995-1999  Madge Networks Ltd.
   5 
   6 */
   7 
   8 #ifndef AMBASSADOR_H
   9 #define AMBASSADOR_H
  10 
  11 
  12 #ifdef CONFIG_ATM_AMBASSADOR_DEBUG
  13 #define DEBUG_AMBASSADOR
  14 #endif
  15 
  16 #define DEV_LABEL                          "amb"
  17 
  18 #ifndef PCI_VENDOR_ID_MADGE
  19 #define PCI_VENDOR_ID_MADGE                0x10B6
  20 #endif
  21 #ifndef PCI_VENDOR_ID_MADGE_AMBASSADOR
  22 #define PCI_DEVICE_ID_MADGE_AMBASSADOR     0x1001
  23 #endif
  24 #ifndef PCI_VENDOR_ID_MADGE_AMBASSADOR_BAD
  25 #define PCI_DEVICE_ID_MADGE_AMBASSADOR_BAD 0x1002
  26 #endif
  27 
  28 // diagnostic output
  29 
  30 #define PRINTK(severity,format,args...) \
  31   printk(severity DEV_LABEL ": " format "\n" , ## args)
  32 
  33 #ifdef DEBUG_AMBASSADOR
  34 
  35 #define DBG_ERR  0x0001
  36 #define DBG_WARN 0x0002
  37 #define DBG_INFO 0x0004
  38 #define DBG_INIT 0x0008
  39 #define DBG_LOAD 0x0010
  40 #define DBG_VCC  0x0020
  41 #define DBG_QOS  0x0040
  42 #define DBG_CMD  0x0080
  43 #define DBG_TX   0x0100
  44 #define DBG_RX   0x0200
  45 #define DBG_SKB  0x0400
  46 #define DBG_POOL 0x0800
  47 #define DBG_IRQ  0x1000
  48 #define DBG_FLOW 0x2000
  49 #define DBG_REGS 0x4000
  50 #define DBG_DATA 0x8000
  51 #define DBG_MASK 0xffff
  52 
  53 /* the ## prevents the annoying double expansion of the macro arguments */
  54 /* KERN_INFO is used since KERN_DEBUG often does not make it to the console */
  55 #define PRINTDB(bits,format,args...) \
  56   ( (debug & (bits)) ? printk (KERN_INFO DEV_LABEL ": " format , ## args) : 1 )
  57 #define PRINTDM(bits,format,args...) \
  58   ( (debug & (bits)) ? printk (format , ## args) : 1 )
  59 #define PRINTDE(bits,format,args...) \
  60   ( (debug & (bits)) ? printk (format "\n" , ## args) : 1 )
  61 #define PRINTD(bits,format,args...) \
  62   ( (debug & (bits)) ? printk (KERN_INFO DEV_LABEL ": " format "\n" , ## args) : 1 )
  63 
  64 #else
  65 
  66 #define PRINTD(bits,format,args...)
  67 #define PRINTDB(bits,format,args...)
  68 #define PRINTDM(bits,format,args...)
  69 #define PRINTDE(bits,format,args...)
  70 
  71 #endif
  72 
  73 #define PRINTDD(bits,format,args...)
  74 #define PRINTDDB(sec,fmt,args...)
  75 #define PRINTDDM(sec,fmt,args...)
  76 #define PRINTDDE(sec,fmt,args...)
  77 
  78 // tunable values (?)
  79 
  80 /* MUST be powers of two -- why ? */
  81 #define COM_Q_ENTRIES        8
  82 #define TX_Q_ENTRIES        32
  83 #define RX_Q_ENTRIES        64
  84 
  85 // fixed values
  86 
  87 // guessing
  88 #define AMB_EXTENT         0x80
  89 
  90 // Minimum allowed size for an Ambassador queue
  91 #define MIN_QUEUE_SIZE     2
  92 
  93 // Ambassador microcode allows 1 to 4 pools, we use 4 (simpler)
  94 #define NUM_RX_POOLS       4
  95 
  96 // minimum RX buffers required to cope with replenishing delay
  97 #define MIN_RX_BUFFERS     1
  98 
  99 // minimum PCI latency we will tolerate (32 IS TOO SMALL)
 100 #define MIN_PCI_LATENCY   64 // 255
 101 
 102 // VCs supported by card (VPI always 0)
 103 #define NUM_VPI_BITS       0
 104 #define NUM_VCI_BITS      10
 105 #define NUM_VCS         1024
 106 
 107 /* The status field bits defined so far. */
 108 #define RX_ERR          0x8000 // always present if there is an error (hmm)
 109 #define CRC_ERR         0x4000 // AAL5 CRC error
 110 #define LEN_ERR         0x2000 // overlength frame
 111 #define ABORT_ERR       0x1000 // zero length field in received frame
 112 #define UNUSED_ERR      0x0800 // buffer returned unused
 113 
 114 // Adaptor commands
 115 
 116 #define SRB_OPEN_VC             0
 117 /* par_0: dwordswap(VC_number) */
 118 /* par_1: dwordswap(flags<<16) or wordswap(flags)*/ 
 119 /* flags:               */
 120 
 121 /* LANE:        0x0004          */
 122 /* NOT_UBR:     0x0008          */
 123 /* ABR:         0x0010          */
 124 
 125 /* RxPool0:     0x0000          */
 126 /* RxPool1:     0x0020          */
 127 /* RxPool2:     0x0040          */
 128 /* RxPool3:     0x0060          */
 129 
 130 /* par_2: dwordswap(fp_rate<<16) or wordswap(fp_rate) */
 131 
 132 #define SRB_CLOSE_VC            1
 133 /* par_0: dwordswap(VC_number) */
 134 
 135 #define SRB_GET_BIA             2
 136 /* returns              */
 137 /* par_0: dwordswap(half BIA) */
 138 /* par_1: dwordswap(half BIA) */
 139 
 140 #define SRB_GET_SUNI_STATS      3
 141 /* par_0: dwordswap(physical_host_address) */
 142 
 143 #define SRB_SET_BITS_8          4
 144 #define SRB_SET_BITS_16         5
 145 #define SRB_SET_BITS_32         6
 146 #define SRB_CLEAR_BITS_8        7
 147 #define SRB_CLEAR_BITS_16       8
 148 #define SRB_CLEAR_BITS_32       9
 149 /* par_0: dwordswap(ATMizer address)    */
 150 /* par_1: dwordswap(mask) */
 151 
 152 #define SRB_SET_8               10
 153 #define SRB_SET_16              11
 154 #define SRB_SET_32              12
 155 /* par_0: dwordswap(ATMizer address)    */
 156 /* par_1: dwordswap(data) */
 157 
 158 #define SRB_GET_32              13
 159 /* par_0: dwordswap(ATMizer address)    */
 160 /* returns                      */
 161 /* par_1: dwordswap(ATMizer data) */
 162 
 163 #define SRB_GET_VERSION         14
 164 /* returns              */
 165 /* par_0: dwordswap(Major Version) */
 166 /* par_1: dwordswap(Minor Version) */
 167 
 168 #define SRB_FLUSH_BUFFER_Q      15
 169 /* Only flags to define which buffer pool; all others must be zero */
 170 /* par_0: dwordswap(flags<<16) or wordswap(flags)*/ 
 171 
 172 #define SRB_GET_DMA_SPEEDS      16
 173 /* returns              */
 174 /* par_0: dwordswap(Read speed (bytes/sec)) */
 175 /* par_1: dwordswap(Write speed (bytes/sec)) */
 176 
 177 #define SRB_MODIFY_VC_RATE      17
 178 /* par_0: dwordswap(VC_number) */
 179 /* par_1: dwordswap(fp_rate<<16) or wordswap(fp_rate) */
 180 
 181 #define SRB_MODIFY_VC_FLAGS     18
 182 /* par_0: dwordswap(VC_number) */
 183 /* par_1: dwordswap(flags<<16) or wordswap(flags)*/ 
 184 
 185 /* flags:               */
 186 
 187 /* LANE:        0x0004          */
 188 /* NOT_UBR:     0x0008          */
 189 /* ABR:         0x0010          */
 190 
 191 /* RxPool0:     0x0000          */
 192 /* RxPool1:     0x0020          */
 193 /* RxPool2:     0x0040          */
 194 /* RxPool3:     0x0060          */
 195 
 196 #define SRB_RATE_SHIFT          16
 197 #define SRB_POOL_SHIFT          (SRB_FLAGS_SHIFT+5)
 198 #define SRB_FLAGS_SHIFT         16
 199 
 200 #define SRB_STOP_TASKING        19
 201 #define SRB_START_TASKING       20
 202 #define SRB_SHUT_DOWN           21
 203 #define MAX_SRB                 21
 204 
 205 #define SRB_COMPLETE            0xffffffff
 206 
 207 #define TX_FRAME                0x80000000
 208 
 209 // number of types of SRB MUST be a power of two -- why?
 210 #define NUM_OF_SRB      32
 211 
 212 // number of bits of period info for rate
 213 #define MAX_RATE_BITS   6
 214 
 215 #define TX_UBR          0x0000
 216 #define TX_UBR_CAPPED   0x0008
 217 #define TX_ABR          0x0018
 218 #define TX_FRAME_NOTCAP 0x0000
 219 #define TX_FRAME_CAPPED 0x8000
 220 
 221 #define FP_155_RATE     0x24b1
 222 #define FP_25_RATE      0x1f9d
 223 
 224 /* #define VERSION_NUMBER 0x01000000 // initial release */
 225 /* #define VERSION_NUMBER 0x01010000 // fixed startup probs PLX MB0 not cleared */
 226 /* #define VERSION_NUMBER 0x01020000 // changed SUNI reset timings; allowed r/w onchip */
 227 
 228 /* #define VERSION_NUMBER 0x01030000 // clear local doorbell int reg on reset */
 229 /* #define VERSION_NUMBER 0x01040000 // PLX bug work around version PLUS */
 230 /* remove race conditions on basic interface */
 231 /* indicate to the host that diagnostics */
 232 /* have finished; if failed, how and what  */
 233 /* failed */
 234 /* fix host memory test to fix PLX bug */
 235 /* allow flash upgrade and BIA upgrade directly */
 236 /*  */
 237 #define VERSION_NUMBER 0x01050025 /* Jason's first hacked version. */
 238 /* Change in download algorithm */
 239 
 240 #define DMA_VALID 0xb728e149 /* completely random */
 241 
 242 #define FLASH_BASE 0xa0c00000
 243 #define FLASH_SIZE 0x00020000                   /* 128K */
 244 #define BIA_BASE (FLASH_BASE+0x0001c000)        /* Flash Sector 7 */
 245 #define BIA_ADDRESS ((void *)0xa0c1c000)
 246 #define PLX_BASE 0xe0000000
 247 
 248 typedef enum {
 249   host_memory_test = 1,
 250   read_adapter_memory,
 251   write_adapter_memory,
 252   adapter_start,
 253   get_version_number,
 254   interrupt_host,
 255   flash_erase_sector,
 256   adap_download_block = 0x20,
 257   adap_erase_flash,
 258   adap_run_in_iram,
 259   adap_end_download
 260 } loader_command;
 261 
 262 #define BAD_COMMAND                     (-1)
 263 #define COMMAND_IN_PROGRESS             1
 264 #define COMMAND_PASSED_TEST             2
 265 #define COMMAND_FAILED_TEST             3
 266 #define COMMAND_READ_DATA_OK            4
 267 #define COMMAND_READ_BAD_ADDRESS        5
 268 #define COMMAND_WRITE_DATA_OK           6
 269 #define COMMAND_WRITE_BAD_ADDRESS       7
 270 #define COMMAND_WRITE_FLASH_FAILURE     8
 271 #define COMMAND_COMPLETE                9
 272 #define COMMAND_FLASH_ERASE_FAILURE     10
 273 #define COMMAND_WRITE_BAD_DATA          11
 274 
 275 /* bit fields for mailbox[0] return values */
 276 
 277 #define GPINT_TST_FAILURE               0x00000001      
 278 #define SUNI_DATA_PATTERN_FAILURE       0x00000002
 279 #define SUNI_DATA_BITS_FAILURE          0x00000004
 280 #define SUNI_UTOPIA_FAILURE             0x00000008
 281 #define SUNI_FIFO_FAILURE               0x00000010
 282 #define SRAM_FAILURE                    0x00000020
 283 #define SELF_TEST_FAILURE               0x0000003f
 284 
 285 /* mailbox[1] = 0 in progress, -1 on completion */
 286 /* mailbox[2] = current test 00 00 test(8 bit) phase(8 bit) */
 287 /* mailbox[3] = last failure, 00 00 test(8 bit) phase(8 bit) */
 288 /* mailbox[4],mailbox[5],mailbox[6] random failure values */
 289 
 290 /* PLX/etc. memory map including command structure */
 291 
 292 /* These registers may also be memory mapped in PCI memory */
 293 
 294 #define UNUSED_LOADER_MAILBOXES 6
 295 
 296 typedef struct {
 297   u32 stuff[16];
 298   union {
 299     struct {
 300       u32 result;
 301       u32 ready;
 302       u32 stuff[UNUSED_LOADER_MAILBOXES];
 303     } loader;
 304     struct {
 305       u32 cmd_address;
 306       u32 tx_address;
 307       u32 rx_address[NUM_RX_POOLS];
 308       u32 gen_counter;
 309       u32 spare;
 310     } adapter;
 311   } mb;
 312   u32 doorbell;
 313   u32 interrupt;
 314   u32 interrupt_control;
 315   u32 reset_control;
 316 } amb_mem;
 317 
 318 /* RESET bit, IRQ (card to host) and doorbell (host to card) enable bits */
 319 #define AMB_RESET_BITS     0x40000000
 320 #define AMB_INTERRUPT_BITS 0x00000300
 321 #define AMB_DOORBELL_BITS  0x00030000
 322 
 323 /* loader commands */
 324 
 325 #define MAX_COMMAND_DATA 13
 326 #define MAX_TRANSFER_DATA 11
 327 
 328 typedef struct {
 329   __be32 address;
 330   __be32 count;
 331   __be32 data[MAX_TRANSFER_DATA];
 332 } transfer_block;
 333 
 334 typedef struct {
 335   __be32 result;
 336   __be32 command;
 337   union {
 338     transfer_block transfer;
 339     __be32 version;
 340     __be32 start;
 341     __be32 data[MAX_COMMAND_DATA];
 342   } payload;
 343   __be32 valid;
 344 } loader_block;
 345 
 346 /* command queue */
 347 
 348 /* Again all data are BIG ENDIAN */
 349 
 350 typedef struct {
 351   union {
 352     struct {
 353       __be32 vc;
 354       __be32 flags;
 355       __be32 rate;
 356     } open;
 357     struct {
 358       __be32 vc;
 359       __be32 rate;
 360     } modify_rate;
 361     struct {
 362       __be32 vc;
 363       __be32 flags;
 364     } modify_flags;
 365     struct {
 366       __be32 vc;
 367     } close;
 368     struct {
 369       __be32 lower4;
 370       __be32 upper2;
 371     } bia;
 372     struct {
 373       __be32 address;
 374     } suni;
 375     struct {
 376       __be32 major;
 377       __be32 minor;
 378     } version;
 379     struct {
 380       __be32 read;
 381       __be32 write;
 382     } speed;
 383     struct {
 384       __be32 flags;
 385     } flush;
 386     struct {
 387       __be32 address;
 388       __be32 data;
 389     } memory;
 390     __be32 par[3];
 391   } args;
 392   __be32 request;
 393 } command;
 394 
 395 /* transmit queues and associated structures */
 396 
 397 /* The hosts transmit structure. All BIG ENDIAN; host address
 398    restricted to first 1GByte, but address passed to the card must
 399    have the top MS bit or'ed in. -- check this */
 400 
 401 /* TX is described by 1+ tx_frags followed by a tx_frag_end */
 402 
 403 typedef struct {
 404   __be32 bytes;
 405   __be32 address;
 406 } tx_frag;
 407 
 408 /* apart from handle the fields here are for the adapter to play with
 409    and should be set to zero */
 410 
 411 typedef struct {
 412   u32   handle;
 413   u16   vc;
 414   u16   next_descriptor_length;
 415   u32   next_descriptor;
 416 #ifdef AMB_NEW_MICROCODE
 417   u8    cpcs_uu;
 418   u8    cpi;
 419   u16   pad;
 420 #endif
 421 } tx_frag_end;
 422 
 423 typedef struct {
 424   tx_frag tx_frag;
 425   tx_frag_end tx_frag_end;
 426   struct sk_buff * skb;
 427 } tx_simple;
 428 
 429 #if 0
 430 typedef union {
 431   tx_frag       fragment;
 432   tx_frag_end   end_of_list;
 433 } tx_descr;
 434 #endif
 435 
 436 /* this "points" to the sequence of fragments and trailer */
 437 
 438 typedef struct {
 439   __be16        vc;
 440   __be16        tx_descr_length;
 441   __be32        tx_descr_addr;
 442 } tx_in;
 443 
 444 /* handle is the handle from tx_in */
 445 
 446 typedef struct {
 447   u32 handle;
 448 } tx_out;
 449 
 450 /* receive frame structure */
 451 
 452 /* All BIG ENDIAN; handle is as passed from host; length is zero for
 453    aborted frames, and frames with errors. Header is actually VC
 454    number, lec-id is NOT yet supported. */
 455 
 456 typedef struct {
 457   u32  handle;
 458   __be16  vc;
 459   __be16  lec_id; // unused
 460   __be16  status;
 461   __be16  length;
 462 } rx_out;
 463 
 464 /* buffer supply structure */
 465 
 466 typedef struct {
 467   u32 handle;
 468   __be32 host_address;
 469 } rx_in;
 470 
 471 /* This first structure is the area in host memory where the adapter
 472    writes its pointer values. These pointer values are BIG ENDIAN and
 473    reside in the same 4MB 'page' as this structure. The host gives the
 474    adapter the address of this block by sending a doorbell interrupt
 475    to the adapter after downloading the code and setting it going. The
 476    addresses have the top 10 bits set to 1010000010b -- really?
 477    
 478    The host must initialise these before handing the block to the
 479    adapter. */
 480 
 481 typedef struct {
 482   __be32 command_start;         /* SRB commands completions */
 483   __be32 command_end;           /* SRB commands completions */
 484   __be32 tx_start;
 485   __be32 tx_end;
 486   __be32 txcom_start;           /* tx completions */
 487   __be32 txcom_end;             /* tx completions */
 488   struct {
 489     __be32 buffer_start;
 490     __be32 buffer_end;
 491     u32 buffer_q_get;
 492     u32 buffer_q_end;
 493     u32 buffer_aptr;
 494     __be32 rx_start;            /* rx completions */
 495     __be32 rx_end;
 496     u32 rx_ptr;
 497     __be32 buffer_size;         /* size of host buffer */
 498   } rec_struct[NUM_RX_POOLS];
 499 #ifdef AMB_NEW_MICROCODE
 500   u16 init_flags;
 501   u16 talk_block_spare;
 502 #endif
 503 } adap_talk_block;
 504 
 505 /* This structure must be kept in line with the vcr image in sarmain.h
 506    
 507    This is the structure in the host filled in by the adapter by
 508    GET_SUNI_STATS */
 509 
 510 typedef struct {
 511   u8    racp_chcs;
 512   u8    racp_uhcs;
 513   u16   spare;
 514   u32   racp_rcell;
 515   u32   tacp_tcell;
 516   u32   flags;
 517   u32   dropped_cells;
 518   u32   dropped_frames;
 519 } suni_stats;
 520 
 521 typedef enum {
 522   dead
 523 } amb_flags;
 524 
 525 #define NEXTQ(current,start,limit) \
 526   ( (current)+1 < (limit) ? (current)+1 : (start) ) 
 527 
 528 typedef struct {
 529   command * start;
 530   command * in;
 531   command * out;
 532   command * limit;
 533 } amb_cq_ptrs;
 534 
 535 typedef struct {
 536   spinlock_t lock;
 537   unsigned int pending;
 538   unsigned int high;
 539   unsigned int filled;
 540   unsigned int maximum; // size - 1 (q implementation)
 541   amb_cq_ptrs ptrs;
 542 } amb_cq;
 543 
 544 typedef struct {
 545   spinlock_t lock;
 546   unsigned int pending;
 547   unsigned int high;
 548   unsigned int filled;
 549   unsigned int maximum; // size - 1 (q implementation)
 550   struct {
 551     tx_in * start;
 552     tx_in * ptr;
 553     tx_in * limit;
 554   } in;
 555   struct {
 556     tx_out * start;
 557     tx_out * ptr;
 558     tx_out * limit;
 559   } out;
 560 } amb_txq;
 561 
 562 typedef struct {
 563   spinlock_t lock;
 564   unsigned int pending;
 565   unsigned int low;
 566   unsigned int emptied;
 567   unsigned int maximum; // size - 1 (q implementation)
 568   struct {
 569     rx_in * start;
 570     rx_in * ptr;
 571     rx_in * limit;
 572   } in;
 573   struct {
 574     rx_out * start;
 575     rx_out * ptr;
 576     rx_out * limit;
 577   } out;
 578   unsigned int buffers_wanted;
 579   unsigned int buffer_size;
 580 } amb_rxq;
 581 
 582 typedef struct {
 583   unsigned long tx_ok;
 584   struct {
 585     unsigned long ok;
 586     unsigned long error;
 587     unsigned long badcrc;
 588     unsigned long toolong;
 589     unsigned long aborted;
 590     unsigned long unused;
 591   } rx;
 592 } amb_stats;
 593 
 594 // a single struct pointed to by atm_vcc->dev_data
 595 
 596 typedef struct {
 597   u8               tx_vc_bits:7;
 598   u8               tx_present:1;
 599 } amb_tx_info;
 600 
 601 typedef struct {
 602   unsigned char    pool;
 603 } amb_rx_info;
 604 
 605 typedef struct {
 606   amb_rx_info      rx_info;
 607   u16              tx_frame_bits;
 608   unsigned int     tx_rate;
 609   unsigned int     rx_rate;
 610 } amb_vcc;
 611 
 612 struct amb_dev {
 613   u8               irq;
 614   unsigned long    flags;
 615   u32              iobase;
 616   u32 *            membase;
 617 
 618   amb_cq           cq;
 619   amb_txq          txq;
 620   amb_rxq          rxq[NUM_RX_POOLS];
 621   
 622   struct mutex     vcc_sf;
 623   amb_tx_info      txer[NUM_VCS];
 624   struct atm_vcc * rxer[NUM_VCS];
 625   unsigned int     tx_avail;
 626   unsigned int     rx_avail;
 627   
 628   amb_stats        stats;
 629   
 630   struct atm_dev * atm_dev;
 631   struct pci_dev * pci_dev;
 632   struct timer_list housekeeping;
 633 };
 634 
 635 typedef struct amb_dev amb_dev;
 636 
 637 #define AMB_DEV(atm_dev) ((amb_dev *) (atm_dev)->dev_data)
 638 #define AMB_VCC(atm_vcc) ((amb_vcc *) (atm_vcc)->dev_data)
 639 
 640 /* rate rounding */
 641 
 642 typedef enum {
 643   round_up,
 644   round_down,
 645   round_nearest
 646 } rounding;
 647 
 648 #endif
/* [<][>][^][v][top][bottom][index][help] */
root/drivers/atm/ambassador.h

INCLUDED FROM
