root/drivers/media/dvb-frontends/s5h1420.c

/* [<][>][^][v][top][bottom][index][help] */

DEFINITIONS

This source file includes following definitions.
  1. s5h1420_readreg
  2. s5h1420_writereg
  3. s5h1420_set_voltage
  4. s5h1420_set_tone
  5. s5h1420_send_master_cmd
  6. s5h1420_recv_slave_reply
  7. s5h1420_send_burst
  8. s5h1420_get_status_bits
  9. s5h1420_read_status
  10. s5h1420_read_ber
  11. s5h1420_read_signal_strength
  12. s5h1420_read_ucblocks
  13. s5h1420_reset
  14. s5h1420_setsymbolrate
  15. s5h1420_getsymbolrate
  16. s5h1420_setfreqoffset
  17. s5h1420_getfreqoffset
  18. s5h1420_setfec_inversion
  19. s5h1420_getfec
  20. s5h1420_getinversion
  21. s5h1420_set_frontend
  22. s5h1420_get_frontend
  23. s5h1420_get_tune_settings
  24. s5h1420_i2c_gate_ctrl
  25. s5h1420_init
  26. s5h1420_sleep
  27. s5h1420_release
  28. s5h1420_tuner_i2c_func
  29. s5h1420_tuner_i2c_tuner_xfer
  30. s5h1420_get_tuner_i2c_adapter
  31. s5h1420_attach

   1 // SPDX-License-Identifier: GPL-2.0-or-later
   2 /*
   3  * Driver for
   4  *    Samsung S5H1420 and
   5  *    PnpNetwork PN1010 QPSK Demodulator
   6  *
   7  * Copyright (C) 2005 Andrew de Quincey <adq_dvb@lidskialf.net>
   8  * Copyright (C) 2005-8 Patrick Boettcher <pb@linuxtv.org>
   9  */
  10 
  11 #include <linux/kernel.h>
  12 #include <linux/module.h>
  13 #include <linux/init.h>
  14 #include <linux/string.h>
  15 #include <linux/slab.h>
  16 #include <linux/delay.h>
  17 #include <linux/jiffies.h>
  18 #include <asm/div64.h>
  19 
  20 #include <linux/i2c.h>
  21 
  22 
  23 #include <media/dvb_frontend.h>
  24 #include "s5h1420.h"
  25 #include "s5h1420_priv.h"
  26 
  27 #define TONE_FREQ 22000
  28 
  29 struct s5h1420_state {
  30         struct i2c_adapter* i2c;
  31         const struct s5h1420_config* config;
  32 
  33         struct dvb_frontend frontend;
  34         struct i2c_adapter tuner_i2c_adapter;
  35 
  36         u8 CON_1_val;
  37 
  38         u8 postlocked:1;
  39         u32 fclk;
  40         u32 tunedfreq;
  41         enum fe_code_rate fec_inner;
  42         u32 symbol_rate;
  43 
  44         /* FIXME: ugly workaround for flexcop's incapable i2c-controller
  45          * it does not support repeated-start, workaround: write addr-1
  46          * and then read
  47          */
  48         u8 shadow[256];
  49 };
  50 
  51 static u32 s5h1420_getsymbolrate(struct s5h1420_state* state);
  52 static int s5h1420_get_tune_settings(struct dvb_frontend* fe,
  53                                      struct dvb_frontend_tune_settings* fesettings);
  54 
  55 
  56 static int debug;
  57 module_param(debug, int, 0644);
  58 MODULE_PARM_DESC(debug, "enable debugging");
  59 
  60 #define dprintk(x...) do { \
  61         if (debug) \
  62                 printk(KERN_DEBUG "S5H1420: " x); \
  63 } while (0)
  64 
  65 static u8 s5h1420_readreg(struct s5h1420_state *state, u8 reg)
  66 {
  67         int ret;
  68         u8 b[2];
  69         struct i2c_msg msg[] = {
  70                 { .addr = state->config->demod_address, .flags = 0, .buf = b, .len = 2 },
  71                 { .addr = state->config->demod_address, .flags = 0, .buf = &reg, .len = 1 },
  72                 { .addr = state->config->demod_address, .flags = I2C_M_RD, .buf = b, .len = 1 },
  73         };
  74 
  75         b[0] = (reg - 1) & 0xff;
  76         b[1] = state->shadow[(reg - 1) & 0xff];
  77 
  78         if (state->config->repeated_start_workaround) {
  79                 ret = i2c_transfer(state->i2c, msg, 3);
  80                 if (ret != 3)
  81                         return ret;
  82         } else {
  83                 ret = i2c_transfer(state->i2c, &msg[1], 1);
  84                 if (ret != 1)
  85                         return ret;
  86                 ret = i2c_transfer(state->i2c, &msg[2], 1);
  87                 if (ret != 1)
  88                         return ret;
  89         }
  90 
  91         /* dprintk("rd(%02x): %02x %02x\n", state->config->demod_address, reg, b[0]); */
  92 
  93         return b[0];
  94 }
  95 
  96 static int s5h1420_writereg (struct s5h1420_state* state, u8 reg, u8 data)
  97 {
  98         u8 buf[] = { reg, data };
  99         struct i2c_msg msg = { .addr = state->config->demod_address, .flags = 0, .buf = buf, .len = 2 };
 100         int err;
 101 
 102         /* dprintk("wr(%02x): %02x %02x\n", state->config->demod_address, reg, data); */
 103         err = i2c_transfer(state->i2c, &msg, 1);
 104         if (err != 1) {
 105                 dprintk("%s: writereg error (err == %i, reg == 0x%02x, data == 0x%02x)\n", __func__, err, reg, data);
 106                 return -EREMOTEIO;
 107         }
 108         state->shadow[reg] = data;
 109 
 110         return 0;
 111 }
 112 
 113 static int s5h1420_set_voltage(struct dvb_frontend *fe,
 114                                enum fe_sec_voltage voltage)
 115 {
 116         struct s5h1420_state* state = fe->demodulator_priv;
 117 
 118         dprintk("enter %s\n", __func__);
 119 
 120         switch(voltage) {
 121         case SEC_VOLTAGE_13:
 122                 s5h1420_writereg(state, 0x3c,
 123                                  (s5h1420_readreg(state, 0x3c) & 0xfe) | 0x02);
 124                 break;
 125 
 126         case SEC_VOLTAGE_18:
 127                 s5h1420_writereg(state, 0x3c, s5h1420_readreg(state, 0x3c) | 0x03);
 128                 break;
 129 
 130         case SEC_VOLTAGE_OFF:
 131                 s5h1420_writereg(state, 0x3c, s5h1420_readreg(state, 0x3c) & 0xfd);
 132                 break;
 133         }
 134 
 135         dprintk("leave %s\n", __func__);
 136         return 0;
 137 }
 138 
 139 static int s5h1420_set_tone(struct dvb_frontend *fe,
 140                             enum fe_sec_tone_mode tone)
 141 {
 142         struct s5h1420_state* state = fe->demodulator_priv;
 143 
 144         dprintk("enter %s\n", __func__);
 145         switch(tone) {
 146         case SEC_TONE_ON:
 147                 s5h1420_writereg(state, 0x3b,
 148                                  (s5h1420_readreg(state, 0x3b) & 0x74) | 0x08);
 149                 break;
 150 
 151         case SEC_TONE_OFF:
 152                 s5h1420_writereg(state, 0x3b,
 153                                  (s5h1420_readreg(state, 0x3b) & 0x74) | 0x01);
 154                 break;
 155         }
 156         dprintk("leave %s\n", __func__);
 157 
 158         return 0;
 159 }
 160 
 161 static int s5h1420_send_master_cmd (struct dvb_frontend* fe,
 162                                     struct dvb_diseqc_master_cmd* cmd)
 163 {
 164         struct s5h1420_state* state = fe->demodulator_priv;
 165         u8 val;
 166         int i;
 167         unsigned long timeout;
 168         int result = 0;
 169 
 170         dprintk("enter %s\n", __func__);
 171         if (cmd->msg_len > sizeof(cmd->msg))
 172                 return -EINVAL;
 173 
 174         /* setup for DISEQC */
 175         val = s5h1420_readreg(state, 0x3b);
 176         s5h1420_writereg(state, 0x3b, 0x02);
 177         msleep(15);
 178 
 179         /* write the DISEQC command bytes */
 180         for(i=0; i< cmd->msg_len; i++) {
 181                 s5h1420_writereg(state, 0x3d + i, cmd->msg[i]);
 182         }
 183 
 184         /* kick off transmission */
 185         s5h1420_writereg(state, 0x3b, s5h1420_readreg(state, 0x3b) |
 186                                       ((cmd->msg_len-1) << 4) | 0x08);
 187 
 188         /* wait for transmission to complete */
 189         timeout = jiffies + ((100*HZ) / 1000);
 190         while(time_before(jiffies, timeout)) {
 191                 if (!(s5h1420_readreg(state, 0x3b) & 0x08))
 192                         break;
 193 
 194                 msleep(5);
 195         }
 196         if (time_after(jiffies, timeout))
 197                 result = -ETIMEDOUT;
 198 
 199         /* restore original settings */
 200         s5h1420_writereg(state, 0x3b, val);
 201         msleep(15);
 202         dprintk("leave %s\n", __func__);
 203         return result;
 204 }
 205 
 206 static int s5h1420_recv_slave_reply (struct dvb_frontend* fe,
 207                                      struct dvb_diseqc_slave_reply* reply)
 208 {
 209         struct s5h1420_state* state = fe->demodulator_priv;
 210         u8 val;
 211         int i;
 212         int length;
 213         unsigned long timeout;
 214         int result = 0;
 215 
 216         /* setup for DISEQC receive */
 217         val = s5h1420_readreg(state, 0x3b);
 218         s5h1420_writereg(state, 0x3b, 0x82); /* FIXME: guess - do we need to set DIS_RDY(0x08) in receive mode? */
 219         msleep(15);
 220 
 221         /* wait for reception to complete */
 222         timeout = jiffies + ((reply->timeout*HZ) / 1000);
 223         while(time_before(jiffies, timeout)) {
 224                 if (!(s5h1420_readreg(state, 0x3b) & 0x80)) /* FIXME: do we test DIS_RDY(0x08) or RCV_EN(0x80)? */
 225                         break;
 226 
 227                 msleep(5);
 228         }
 229         if (time_after(jiffies, timeout)) {
 230                 result = -ETIMEDOUT;
 231                 goto exit;
 232         }
 233 
 234         /* check error flag - FIXME: not sure what this does - docs do not describe
 235          * beyond "error flag for diseqc receive data :( */
 236         if (s5h1420_readreg(state, 0x49)) {
 237                 result = -EIO;
 238                 goto exit;
 239         }
 240 
 241         /* check length */
 242         length = (s5h1420_readreg(state, 0x3b) & 0x70) >> 4;
 243         if (length > sizeof(reply->msg)) {
 244                 result = -EOVERFLOW;
 245                 goto exit;
 246         }
 247         reply->msg_len = length;
 248 
 249         /* extract data */
 250         for(i=0; i< length; i++) {
 251                 reply->msg[i] = s5h1420_readreg(state, 0x3d + i);
 252         }
 253 
 254 exit:
 255         /* restore original settings */
 256         s5h1420_writereg(state, 0x3b, val);
 257         msleep(15);
 258         return result;
 259 }
 260 
 261 static int s5h1420_send_burst(struct dvb_frontend *fe,
 262                               enum fe_sec_mini_cmd minicmd)
 263 {
 264         struct s5h1420_state* state = fe->demodulator_priv;
 265         u8 val;
 266         int result = 0;
 267         unsigned long timeout;
 268 
 269         /* setup for tone burst */
 270         val = s5h1420_readreg(state, 0x3b);
 271         s5h1420_writereg(state, 0x3b, (s5h1420_readreg(state, 0x3b) & 0x70) | 0x01);
 272 
 273         /* set value for B position if requested */
 274         if (minicmd == SEC_MINI_B) {
 275                 s5h1420_writereg(state, 0x3b, s5h1420_readreg(state, 0x3b) | 0x04);
 276         }
 277         msleep(15);
 278 
 279         /* start transmission */
 280         s5h1420_writereg(state, 0x3b, s5h1420_readreg(state, 0x3b) | 0x08);
 281 
 282         /* wait for transmission to complete */
 283         timeout = jiffies + ((100*HZ) / 1000);
 284         while(time_before(jiffies, timeout)) {
 285                 if (!(s5h1420_readreg(state, 0x3b) & 0x08))
 286                         break;
 287 
 288                 msleep(5);
 289         }
 290         if (time_after(jiffies, timeout))
 291                 result = -ETIMEDOUT;
 292 
 293         /* restore original settings */
 294         s5h1420_writereg(state, 0x3b, val);
 295         msleep(15);
 296         return result;
 297 }
 298 
 299 static enum fe_status s5h1420_get_status_bits(struct s5h1420_state *state)
 300 {
 301         u8 val;
 302         enum fe_status status = 0;
 303 
 304         val = s5h1420_readreg(state, 0x14);
 305         if (val & 0x02)
 306                 status |=  FE_HAS_SIGNAL;
 307         if (val & 0x01)
 308                 status |=  FE_HAS_CARRIER;
 309         val = s5h1420_readreg(state, 0x36);
 310         if (val & 0x01)
 311                 status |=  FE_HAS_VITERBI;
 312         if (val & 0x20)
 313                 status |=  FE_HAS_SYNC;
 314         if (status == (FE_HAS_SIGNAL|FE_HAS_CARRIER|FE_HAS_VITERBI|FE_HAS_SYNC))
 315                 status |=  FE_HAS_LOCK;
 316 
 317         return status;
 318 }
 319 
 320 static int s5h1420_read_status(struct dvb_frontend *fe,
 321                                enum fe_status *status)
 322 {
 323         struct s5h1420_state* state = fe->demodulator_priv;
 324         u8 val;
 325 
 326         dprintk("enter %s\n", __func__);
 327 
 328         if (status == NULL)
 329                 return -EINVAL;
 330 
 331         /* determine lock state */
 332         *status = s5h1420_get_status_bits(state);
 333 
 334         /* fix for FEC 5/6 inversion issue - if it doesn't quite lock, invert
 335         the inversion, wait a bit and check again */
 336         if (*status == (FE_HAS_SIGNAL | FE_HAS_CARRIER | FE_HAS_VITERBI)) {
 337                 val = s5h1420_readreg(state, Vit10);
 338                 if ((val & 0x07) == 0x03) {
 339                         if (val & 0x08)
 340                                 s5h1420_writereg(state, Vit09, 0x13);
 341                         else
 342                                 s5h1420_writereg(state, Vit09, 0x1b);
 343 
 344                         /* wait a bit then update lock status */
 345                         mdelay(200);
 346                         *status = s5h1420_get_status_bits(state);
 347                 }
 348         }
 349 
 350         /* perform post lock setup */
 351         if ((*status & FE_HAS_LOCK) && !state->postlocked) {
 352 
 353                 /* calculate the data rate */
 354                 u32 tmp = s5h1420_getsymbolrate(state);
 355                 switch (s5h1420_readreg(state, Vit10) & 0x07) {
 356                 case 0: tmp = (tmp * 2 * 1) / 2; break;
 357                 case 1: tmp = (tmp * 2 * 2) / 3; break;
 358                 case 2: tmp = (tmp * 2 * 3) / 4; break;
 359                 case 3: tmp = (tmp * 2 * 5) / 6; break;
 360                 case 4: tmp = (tmp * 2 * 6) / 7; break;
 361                 case 5: tmp = (tmp * 2 * 7) / 8; break;
 362                 }
 363 
 364                 if (tmp == 0) {
 365                         printk(KERN_ERR "s5h1420: avoided division by 0\n");
 366                         tmp = 1;
 367                 }
 368                 tmp = state->fclk / tmp;
 369 
 370 
 371                 /* set the MPEG_CLK_INTL for the calculated data rate */
 372                 if (tmp < 2)
 373                         val = 0x00;
 374                 else if (tmp < 5)
 375                         val = 0x01;
 376                 else if (tmp < 9)
 377                         val = 0x02;
 378                 else if (tmp < 13)
 379                         val = 0x03;
 380                 else if (tmp < 17)
 381                         val = 0x04;
 382                 else if (tmp < 25)
 383                         val = 0x05;
 384                 else if (tmp < 33)
 385                         val = 0x06;
 386                 else
 387                         val = 0x07;
 388                 dprintk("for MPEG_CLK_INTL %d %x\n", tmp, val);
 389 
 390                 s5h1420_writereg(state, FEC01, 0x18);
 391                 s5h1420_writereg(state, FEC01, 0x10);
 392                 s5h1420_writereg(state, FEC01, val);
 393 
 394                 /* Enable "MPEG_Out" */
 395                 val = s5h1420_readreg(state, Mpeg02);
 396                 s5h1420_writereg(state, Mpeg02, val | (1 << 6));
 397 
 398                 /* kicker disable */
 399                 val = s5h1420_readreg(state, QPSK01) & 0x7f;
 400                 s5h1420_writereg(state, QPSK01, val);
 401 
 402                 /* DC freeze TODO it was never activated by default or it can stay activated */
 403 
 404                 if (s5h1420_getsymbolrate(state) >= 20000000) {
 405                         s5h1420_writereg(state, Loop04, 0x8a);
 406                         s5h1420_writereg(state, Loop05, 0x6a);
 407                 } else {
 408                         s5h1420_writereg(state, Loop04, 0x58);
 409                         s5h1420_writereg(state, Loop05, 0x27);
 410                 }
 411 
 412                 /* post-lock processing has been done! */
 413                 state->postlocked = 1;
 414         }
 415 
 416         dprintk("leave %s\n", __func__);
 417 
 418         return 0;
 419 }
 420 
 421 static int s5h1420_read_ber(struct dvb_frontend* fe, u32* ber)
 422 {
 423         struct s5h1420_state* state = fe->demodulator_priv;
 424 
 425         s5h1420_writereg(state, 0x46, 0x1d);
 426         mdelay(25);
 427 
 428         *ber = (s5h1420_readreg(state, 0x48) << 8) | s5h1420_readreg(state, 0x47);
 429 
 430         return 0;
 431 }
 432 
 433 static int s5h1420_read_signal_strength(struct dvb_frontend* fe, u16* strength)
 434 {
 435         struct s5h1420_state* state = fe->demodulator_priv;
 436 
 437         u8 val = s5h1420_readreg(state, 0x15);
 438 
 439         *strength =  (u16) ((val << 8) | val);
 440 
 441         return 0;
 442 }
 443 
 444 static int s5h1420_read_ucblocks(struct dvb_frontend* fe, u32* ucblocks)
 445 {
 446         struct s5h1420_state* state = fe->demodulator_priv;
 447 
 448         s5h1420_writereg(state, 0x46, 0x1f);
 449         mdelay(25);
 450 
 451         *ucblocks = (s5h1420_readreg(state, 0x48) << 8) | s5h1420_readreg(state, 0x47);
 452 
 453         return 0;
 454 }
 455 
 456 static void s5h1420_reset(struct s5h1420_state* state)
 457 {
 458         dprintk("%s\n", __func__);
 459         s5h1420_writereg (state, 0x01, 0x08);
 460         s5h1420_writereg (state, 0x01, 0x00);
 461         udelay(10);
 462 }
 463 
 464 static void s5h1420_setsymbolrate(struct s5h1420_state* state,
 465                                   struct dtv_frontend_properties *p)
 466 {
 467         u8 v;
 468         u64 val;
 469 
 470         dprintk("enter %s\n", __func__);
 471 
 472         val = ((u64) p->symbol_rate / 1000ULL) * (1ULL<<24);
 473         if (p->symbol_rate < 29000000)
 474                 val *= 2;
 475         do_div(val, (state->fclk / 1000));
 476 
 477         dprintk("symbol rate register: %06llx\n", (unsigned long long)val);
 478 
 479         v = s5h1420_readreg(state, Loop01);
 480         s5h1420_writereg(state, Loop01, v & 0x7f);
 481         s5h1420_writereg(state, Tnco01, val >> 16);
 482         s5h1420_writereg(state, Tnco02, val >> 8);
 483         s5h1420_writereg(state, Tnco03, val & 0xff);
 484         s5h1420_writereg(state, Loop01,  v | 0x80);
 485         dprintk("leave %s\n", __func__);
 486 }
 487 
 488 static u32 s5h1420_getsymbolrate(struct s5h1420_state* state)
 489 {
 490         return state->symbol_rate;
 491 }
 492 
 493 static void s5h1420_setfreqoffset(struct s5h1420_state* state, int freqoffset)
 494 {
 495         int val;
 496         u8 v;
 497 
 498         dprintk("enter %s\n", __func__);
 499 
 500         /* remember freqoffset is in kHz, but the chip wants the offset in Hz, so
 501          * divide fclk by 1000000 to get the correct value. */
 502         val = -(int) ((freqoffset * (1<<24)) / (state->fclk / 1000000));
 503 
 504         dprintk("phase rotator/freqoffset: %d %06x\n", freqoffset, val);
 505 
 506         v = s5h1420_readreg(state, Loop01);
 507         s5h1420_writereg(state, Loop01, v & 0xbf);
 508         s5h1420_writereg(state, Pnco01, val >> 16);
 509         s5h1420_writereg(state, Pnco02, val >> 8);
 510         s5h1420_writereg(state, Pnco03, val & 0xff);
 511         s5h1420_writereg(state, Loop01, v | 0x40);
 512         dprintk("leave %s\n", __func__);
 513 }
 514 
 515 static int s5h1420_getfreqoffset(struct s5h1420_state* state)
 516 {
 517         int val;
 518 
 519         s5h1420_writereg(state, 0x06, s5h1420_readreg(state, 0x06) | 0x08);
 520         val  = s5h1420_readreg(state, 0x0e) << 16;
 521         val |= s5h1420_readreg(state, 0x0f) << 8;
 522         val |= s5h1420_readreg(state, 0x10);
 523         s5h1420_writereg(state, 0x06, s5h1420_readreg(state, 0x06) & 0xf7);
 524 
 525         if (val & 0x800000)
 526                 val |= 0xff000000;
 527 
 528         /* remember freqoffset is in kHz, but the chip wants the offset in Hz, so
 529          * divide fclk by 1000000 to get the correct value. */
 530         val = (((-val) * (state->fclk/1000000)) / (1<<24));
 531 
 532         return val;
 533 }
 534 
 535 static void s5h1420_setfec_inversion(struct s5h1420_state* state,
 536                                      struct dtv_frontend_properties *p)
 537 {
 538         u8 inversion = 0;
 539         u8 vit08, vit09;
 540 
 541         dprintk("enter %s\n", __func__);
 542 
 543         if (p->inversion == INVERSION_OFF)
 544                 inversion = state->config->invert ? 0x08 : 0;
 545         else if (p->inversion == INVERSION_ON)
 546                 inversion = state->config->invert ? 0 : 0x08;
 547 
 548         if ((p->fec_inner == FEC_AUTO) || (p->inversion == INVERSION_AUTO)) {
 549                 vit08 = 0x3f;
 550                 vit09 = 0;
 551         } else {
 552                 switch (p->fec_inner) {
 553                 case FEC_1_2:
 554                         vit08 = 0x01;
 555                         vit09 = 0x10;
 556                         break;
 557 
 558                 case FEC_2_3:
 559                         vit08 = 0x02;
 560                         vit09 = 0x11;
 561                         break;
 562 
 563                 case FEC_3_4:
 564                         vit08 = 0x04;
 565                         vit09 = 0x12;
 566                         break;
 567 
 568                 case FEC_5_6:
 569                         vit08 = 0x08;
 570                         vit09 = 0x13;
 571                         break;
 572 
 573                 case FEC_6_7:
 574                         vit08 = 0x10;
 575                         vit09 = 0x14;
 576                         break;
 577 
 578                 case FEC_7_8:
 579                         vit08 = 0x20;
 580                         vit09 = 0x15;
 581                         break;
 582 
 583                 default:
 584                         return;
 585                 }
 586         }
 587         vit09 |= inversion;
 588         dprintk("fec: %02x %02x\n", vit08, vit09);
 589         s5h1420_writereg(state, Vit08, vit08);
 590         s5h1420_writereg(state, Vit09, vit09);
 591         dprintk("leave %s\n", __func__);
 592 }
 593 
 594 static enum fe_code_rate s5h1420_getfec(struct s5h1420_state *state)
 595 {
 596         switch(s5h1420_readreg(state, 0x32) & 0x07) {
 597         case 0:
 598                 return FEC_1_2;
 599 
 600         case 1:
 601                 return FEC_2_3;
 602 
 603         case 2:
 604                 return FEC_3_4;
 605 
 606         case 3:
 607                 return FEC_5_6;
 608 
 609         case 4:
 610                 return FEC_6_7;
 611 
 612         case 5:
 613                 return FEC_7_8;
 614         }
 615 
 616         return FEC_NONE;
 617 }
 618 
 619 static enum fe_spectral_inversion
 620 s5h1420_getinversion(struct s5h1420_state *state)
 621 {
 622         if (s5h1420_readreg(state, 0x32) & 0x08)
 623                 return INVERSION_ON;
 624 
 625         return INVERSION_OFF;
 626 }
 627 
 628 static int s5h1420_set_frontend(struct dvb_frontend *fe)
 629 {
 630         struct dtv_frontend_properties *p = &fe->dtv_property_cache;
 631         struct s5h1420_state* state = fe->demodulator_priv;
 632         int frequency_delta;
 633         struct dvb_frontend_tune_settings fesettings;
 634 
 635         dprintk("enter %s\n", __func__);
 636 
 637         /* check if we should do a fast-tune */
 638         s5h1420_get_tune_settings(fe, &fesettings);
 639         frequency_delta = p->frequency - state->tunedfreq;
 640         if ((frequency_delta > -fesettings.max_drift) &&
 641                         (frequency_delta < fesettings.max_drift) &&
 642                         (frequency_delta != 0) &&
 643                         (state->fec_inner == p->fec_inner) &&
 644                         (state->symbol_rate == p->symbol_rate)) {
 645 
 646                 if (fe->ops.tuner_ops.set_params) {
 647                         fe->ops.tuner_ops.set_params(fe);
 648                         if (fe->ops.i2c_gate_ctrl) fe->ops.i2c_gate_ctrl(fe, 0);
 649                 }
 650                 if (fe->ops.tuner_ops.get_frequency) {
 651                         u32 tmp;
 652                         fe->ops.tuner_ops.get_frequency(fe, &tmp);
 653                         if (fe->ops.i2c_gate_ctrl) fe->ops.i2c_gate_ctrl(fe, 0);
 654                         s5h1420_setfreqoffset(state, p->frequency - tmp);
 655                 } else {
 656                         s5h1420_setfreqoffset(state, 0);
 657                 }
 658                 dprintk("simple tune\n");
 659                 return 0;
 660         }
 661         dprintk("tuning demod\n");
 662 
 663         /* first of all, software reset */
 664         s5h1420_reset(state);
 665 
 666         /* set s5h1420 fclk PLL according to desired symbol rate */
 667         if (p->symbol_rate > 33000000)
 668                 state->fclk = 80000000;
 669         else if (p->symbol_rate > 28500000)
 670                 state->fclk = 59000000;
 671         else if (p->symbol_rate > 25000000)
 672                 state->fclk = 86000000;
 673         else if (p->symbol_rate > 1900000)
 674                 state->fclk = 88000000;
 675         else
 676                 state->fclk = 44000000;
 677 
 678         dprintk("pll01: %d, ToneFreq: %d\n", state->fclk/1000000 - 8, (state->fclk + (TONE_FREQ * 32) - 1) / (TONE_FREQ * 32));
 679         s5h1420_writereg(state, PLL01, state->fclk/1000000 - 8);
 680         s5h1420_writereg(state, PLL02, 0x40);
 681         s5h1420_writereg(state, DiS01, (state->fclk + (TONE_FREQ * 32) - 1) / (TONE_FREQ * 32));
 682 
 683         /* TODO DC offset removal, config parameter ? */
 684         if (p->symbol_rate > 29000000)
 685                 s5h1420_writereg(state, QPSK01, 0xae | 0x10);
 686         else
 687                 s5h1420_writereg(state, QPSK01, 0xac | 0x10);
 688 
 689         /* set misc registers */
 690         s5h1420_writereg(state, CON_1, 0x00);
 691         s5h1420_writereg(state, QPSK02, 0x00);
 692         s5h1420_writereg(state, Pre01, 0xb0);
 693 
 694         s5h1420_writereg(state, Loop01, 0xF0);
 695         s5h1420_writereg(state, Loop02, 0x2a); /* e7 for s5h1420 */
 696         s5h1420_writereg(state, Loop03, 0x79); /* 78 for s5h1420 */
 697         if (p->symbol_rate > 20000000)
 698                 s5h1420_writereg(state, Loop04, 0x79);
 699         else
 700                 s5h1420_writereg(state, Loop04, 0x58);
 701         s5h1420_writereg(state, Loop05, 0x6b);
 702 
 703         if (p->symbol_rate >= 8000000)
 704                 s5h1420_writereg(state, Post01, (0 << 6) | 0x10);
 705         else if (p->symbol_rate >= 4000000)
 706                 s5h1420_writereg(state, Post01, (1 << 6) | 0x10);
 707         else
 708                 s5h1420_writereg(state, Post01, (3 << 6) | 0x10);
 709 
 710         s5h1420_writereg(state, Monitor12, 0x00); /* unfreeze DC compensation */
 711 
 712         s5h1420_writereg(state, Sync01, 0x33);
 713         s5h1420_writereg(state, Mpeg01, state->config->cdclk_polarity);
 714         s5h1420_writereg(state, Mpeg02, 0x3d); /* Parallel output more, disabled -> enabled later */
 715         s5h1420_writereg(state, Err01, 0x03); /* 0x1d for s5h1420 */
 716 
 717         s5h1420_writereg(state, Vit06, 0x6e); /* 0x8e for s5h1420 */
 718         s5h1420_writereg(state, DiS03, 0x00);
 719         s5h1420_writereg(state, Rf01, 0x61); /* Tuner i2c address - for the gate controller */
 720 
 721         /* set tuner PLL */
 722         if (fe->ops.tuner_ops.set_params) {
 723                 fe->ops.tuner_ops.set_params(fe);
 724                 if (fe->ops.i2c_gate_ctrl)
 725                         fe->ops.i2c_gate_ctrl(fe, 0);
 726                 s5h1420_setfreqoffset(state, 0);
 727         }
 728 
 729         /* set the reset of the parameters */
 730         s5h1420_setsymbolrate(state, p);
 731         s5h1420_setfec_inversion(state, p);
 732 
 733         /* start QPSK */
 734         s5h1420_writereg(state, QPSK01, s5h1420_readreg(state, QPSK01) | 1);
 735 
 736         state->fec_inner = p->fec_inner;
 737         state->symbol_rate = p->symbol_rate;
 738         state->postlocked = 0;
 739         state->tunedfreq = p->frequency;
 740 
 741         dprintk("leave %s\n", __func__);
 742         return 0;
 743 }
 744 
 745 static int s5h1420_get_frontend(struct dvb_frontend* fe,
 746                                 struct dtv_frontend_properties *p)
 747 {
 748         struct s5h1420_state* state = fe->demodulator_priv;
 749 
 750         p->frequency = state->tunedfreq + s5h1420_getfreqoffset(state);
 751         p->inversion = s5h1420_getinversion(state);
 752         p->symbol_rate = s5h1420_getsymbolrate(state);
 753         p->fec_inner = s5h1420_getfec(state);
 754 
 755         return 0;
 756 }
 757 
 758 static int s5h1420_get_tune_settings(struct dvb_frontend* fe,
 759                                      struct dvb_frontend_tune_settings* fesettings)
 760 {
 761         struct dtv_frontend_properties *p = &fe->dtv_property_cache;
 762         if (p->symbol_rate > 20000000) {
 763                 fesettings->min_delay_ms = 50;
 764                 fesettings->step_size = 2000;
 765                 fesettings->max_drift = 8000;
 766         } else if (p->symbol_rate > 12000000) {
 767                 fesettings->min_delay_ms = 100;
 768                 fesettings->step_size = 1500;
 769                 fesettings->max_drift = 9000;
 770         } else if (p->symbol_rate > 8000000) {
 771                 fesettings->min_delay_ms = 100;
 772                 fesettings->step_size = 1000;
 773                 fesettings->max_drift = 8000;
 774         } else if (p->symbol_rate > 4000000) {
 775                 fesettings->min_delay_ms = 100;
 776                 fesettings->step_size = 500;
 777                 fesettings->max_drift = 7000;
 778         } else if (p->symbol_rate > 2000000) {
 779                 fesettings->min_delay_ms = 200;
 780                 fesettings->step_size = (p->symbol_rate / 8000);
 781                 fesettings->max_drift = 14 * fesettings->step_size;
 782         } else {
 783                 fesettings->min_delay_ms = 200;
 784                 fesettings->step_size = (p->symbol_rate / 8000);
 785                 fesettings->max_drift = 18 * fesettings->step_size;
 786         }
 787 
 788         return 0;
 789 }
 790 
 791 static int s5h1420_i2c_gate_ctrl(struct dvb_frontend* fe, int enable)
 792 {
 793         struct s5h1420_state* state = fe->demodulator_priv;
 794 
 795         if (enable)
 796                 return s5h1420_writereg(state, 0x02, state->CON_1_val | 1);
 797         else
 798                 return s5h1420_writereg(state, 0x02, state->CON_1_val & 0xfe);
 799 }
 800 
 801 static int s5h1420_init (struct dvb_frontend* fe)
 802 {
 803         struct s5h1420_state* state = fe->demodulator_priv;
 804 
 805         /* disable power down and do reset */
 806         state->CON_1_val = state->config->serial_mpeg << 4;
 807         s5h1420_writereg(state, 0x02, state->CON_1_val);
 808         msleep(10);
 809         s5h1420_reset(state);
 810 
 811         return 0;
 812 }
 813 
 814 static int s5h1420_sleep(struct dvb_frontend* fe)
 815 {
 816         struct s5h1420_state* state = fe->demodulator_priv;
 817         state->CON_1_val = 0x12;
 818         return s5h1420_writereg(state, 0x02, state->CON_1_val);
 819 }
 820 
 821 static void s5h1420_release(struct dvb_frontend* fe)
 822 {
 823         struct s5h1420_state* state = fe->demodulator_priv;
 824         i2c_del_adapter(&state->tuner_i2c_adapter);
 825         kfree(state);
 826 }
 827 
 828 static u32 s5h1420_tuner_i2c_func(struct i2c_adapter *adapter)
 829 {
 830         return I2C_FUNC_I2C;
 831 }
 832 
 833 static int s5h1420_tuner_i2c_tuner_xfer(struct i2c_adapter *i2c_adap, struct i2c_msg msg[], int num)
 834 {
 835         struct s5h1420_state *state = i2c_get_adapdata(i2c_adap);
 836         struct i2c_msg m[3];
 837         u8 tx_open[2] = { CON_1, state->CON_1_val | 1 }; /* repeater stops once there was a stop condition */
 838 
 839         if (1 + num > ARRAY_SIZE(m)) {
 840                 printk(KERN_WARNING
 841                        "%s: i2c xfer: num=%d is too big!\n",
 842                        KBUILD_MODNAME, num);
 843                 return  -EOPNOTSUPP;
 844         }
 845 
 846         memset(m, 0, sizeof(struct i2c_msg) * (1 + num));
 847 
 848         m[0].addr = state->config->demod_address;
 849         m[0].buf  = tx_open;
 850         m[0].len  = 2;
 851 
 852         memcpy(&m[1], msg, sizeof(struct i2c_msg) * num);
 853 
 854         return i2c_transfer(state->i2c, m, 1 + num) == 1 + num ? num : -EIO;
 855 }
 856 
 857 static const struct i2c_algorithm s5h1420_tuner_i2c_algo = {
 858         .master_xfer   = s5h1420_tuner_i2c_tuner_xfer,
 859         .functionality = s5h1420_tuner_i2c_func,
 860 };
 861 
 862 struct i2c_adapter *s5h1420_get_tuner_i2c_adapter(struct dvb_frontend *fe)
 863 {
 864         struct s5h1420_state *state = fe->demodulator_priv;
 865         return &state->tuner_i2c_adapter;
 866 }
 867 EXPORT_SYMBOL(s5h1420_get_tuner_i2c_adapter);
 868 
 869 static const struct dvb_frontend_ops s5h1420_ops;
 870 
 871 struct dvb_frontend *s5h1420_attach(const struct s5h1420_config *config,
 872                                     struct i2c_adapter *i2c)
 873 {
 874         /* allocate memory for the internal state */
 875         struct s5h1420_state *state = kzalloc(sizeof(struct s5h1420_state), GFP_KERNEL);
 876         u8 i;
 877 
 878         if (state == NULL)
 879                 goto error;
 880 
 881         /* setup the state */
 882         state->config = config;
 883         state->i2c = i2c;
 884         state->postlocked = 0;
 885         state->fclk = 88000000;
 886         state->tunedfreq = 0;
 887         state->fec_inner = FEC_NONE;
 888         state->symbol_rate = 0;
 889 
 890         /* check if the demod is there + identify it */
 891         i = s5h1420_readreg(state, ID01);
 892         if (i != 0x03)
 893                 goto error;
 894 
 895         memset(state->shadow, 0xff, sizeof(state->shadow));
 896 
 897         for (i = 0; i < 0x50; i++)
 898                 state->shadow[i] = s5h1420_readreg(state, i);
 899 
 900         /* create dvb_frontend */
 901         memcpy(&state->frontend.ops, &s5h1420_ops, sizeof(struct dvb_frontend_ops));
 902         state->frontend.demodulator_priv = state;
 903 
 904         /* create tuner i2c adapter */
 905         strscpy(state->tuner_i2c_adapter.name, "S5H1420-PN1010 tuner I2C bus",
 906                 sizeof(state->tuner_i2c_adapter.name));
 907         state->tuner_i2c_adapter.algo      = &s5h1420_tuner_i2c_algo;
 908         state->tuner_i2c_adapter.algo_data = NULL;
 909         i2c_set_adapdata(&state->tuner_i2c_adapter, state);
 910         if (i2c_add_adapter(&state->tuner_i2c_adapter) < 0) {
 911                 printk(KERN_ERR "S5H1420/PN1010: tuner i2c bus could not be initialized\n");
 912                 goto error;
 913         }
 914 
 915         return &state->frontend;
 916 
 917 error:
 918         kfree(state);
 919         return NULL;
 920 }
 921 EXPORT_SYMBOL(s5h1420_attach);
 922 
 923 static const struct dvb_frontend_ops s5h1420_ops = {
 924         .delsys = { SYS_DVBS },
 925         .info = {
 926                 .name     = "Samsung S5H1420/PnpNetwork PN1010 DVB-S",
 927                 .frequency_min_hz    =  950 * MHz,
 928                 .frequency_max_hz    = 2150 * MHz,
 929                 .frequency_stepsize_hz = 125 * kHz,
 930                 .frequency_tolerance_hz  = 29500 * kHz,
 931                 .symbol_rate_min  = 1000000,
 932                 .symbol_rate_max  = 45000000,
 933                 /*  .symbol_rate_tolerance  = ???,*/
 934                 .caps = FE_CAN_INVERSION_AUTO |
 935                 FE_CAN_FEC_1_2 | FE_CAN_FEC_2_3 | FE_CAN_FEC_3_4 |
 936                 FE_CAN_FEC_5_6 | FE_CAN_FEC_6_7 | FE_CAN_FEC_7_8 | FE_CAN_FEC_AUTO |
 937                 FE_CAN_QPSK
 938         },
 939 
 940         .release = s5h1420_release,
 941 
 942         .init = s5h1420_init,
 943         .sleep = s5h1420_sleep,
 944         .i2c_gate_ctrl = s5h1420_i2c_gate_ctrl,
 945 
 946         .set_frontend = s5h1420_set_frontend,
 947         .get_frontend = s5h1420_get_frontend,
 948         .get_tune_settings = s5h1420_get_tune_settings,
 949 
 950         .read_status = s5h1420_read_status,
 951         .read_ber = s5h1420_read_ber,
 952         .read_signal_strength = s5h1420_read_signal_strength,
 953         .read_ucblocks = s5h1420_read_ucblocks,
 954 
 955         .diseqc_send_master_cmd = s5h1420_send_master_cmd,
 956         .diseqc_recv_slave_reply = s5h1420_recv_slave_reply,
 957         .diseqc_send_burst = s5h1420_send_burst,
 958         .set_tone = s5h1420_set_tone,
 959         .set_voltage = s5h1420_set_voltage,
 960 };
 961 
 962 MODULE_DESCRIPTION("Samsung S5H1420/PnpNetwork PN1010 DVB-S Demodulator driver");
 963 MODULE_AUTHOR("Andrew de Quincey, Patrick Boettcher");
 964 MODULE_LICENSE("GPL");

/* [<][>][^][v][top][bottom][index][help] */