This source file includes following definitions.
- em28xx_tuner_callback
- em28xx_set_xclk_i2c_speed
- em28xx_set_model
- em28xx_wait_until_ac97_features_equals
- em28xx_pre_card_setup
- em28xx_hint_board
- em28xx_card_setup
- em28xx_setup_xc3028
- request_module_async
- request_modules
- flush_request_modules
- em28xx_media_device_init
- em28xx_unregister_media_device
- em28xx_release_resources
- em28xx_free_device
- em28xx_init_dev
- em28xx_duplicate_dev
- em28xx_check_usb_descriptor
- em28xx_usb_probe
- em28xx_usb_disconnect
- em28xx_usb_suspend
- em28xx_usb_resume
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22 #include "em28xx.h"
23
24 #include <linux/init.h>
25 #include <linux/module.h>
26 #include <linux/slab.h>
27 #include <linux/delay.h>
28 #include <linux/i2c.h>
29 #include <linux/usb.h>
30 #include <media/tuner.h>
31 #include <media/drv-intf/msp3400.h>
32 #include <media/i2c/saa7115.h>
33 #include <dt-bindings/media/tvp5150.h>
34 #include <media/i2c/tvaudio.h>
35 #include <media/tveeprom.h>
36 #include <media/v4l2-common.h>
37 #include <sound/ac97_codec.h>
38
39 #define DRIVER_NAME "em28xx"
40
41 static int tuner = -1;
42 module_param(tuner, int, 0444);
43 MODULE_PARM_DESC(tuner, "tuner type");
44
45 static unsigned int disable_ir;
46 module_param(disable_ir, int, 0444);
47 MODULE_PARM_DESC(disable_ir, "disable infrared remote support");
48
49 static unsigned int disable_usb_speed_check;
50 module_param(disable_usb_speed_check, int, 0444);
51 MODULE_PARM_DESC(disable_usb_speed_check,
52 "override min bandwidth requirement of 480M bps");
53
54 static unsigned int card[] = {[0 ... (EM28XX_MAXBOARDS - 1)] = -1U };
55 module_param_array(card, int, NULL, 0444);
56 MODULE_PARM_DESC(card, "card type");
57
58 static int usb_xfer_mode = -1;
59 module_param(usb_xfer_mode, int, 0444);
60 MODULE_PARM_DESC(usb_xfer_mode,
61 "USB transfer mode for frame data (-1 = auto, 0 = prefer isoc, 1 = prefer bulk)");
62
63
64 static DECLARE_BITMAP(em28xx_devused, EM28XX_MAXBOARDS);
65
66 struct em28xx_hash_table {
67 unsigned long hash;
68 unsigned int model;
69 unsigned int tuner;
70 };
71
72 static void em28xx_pre_card_setup(struct em28xx *dev);
73
74
75
76
77
78
79 static const struct em28xx_reg_seq default_analog[] = {
80 {EM2820_R08_GPIO_CTRL, 0x6d, ~EM_GPIO_4, 10},
81 { -1, -1, -1, -1},
82 };
83
84
85 static const struct em28xx_reg_seq default_digital[] = {
86 {EM2820_R08_GPIO_CTRL, 0x6e, ~EM_GPIO_4, 10},
87 { -1, -1, -1, -1},
88 };
89
90
91 static struct em28xx_reg_seq zolid_tuner[] = {
92 {EM2820_R08_GPIO_CTRL, 0xfd, 0xff, 100},
93 {EM2820_R08_GPIO_CTRL, 0xfe, 0xff, 100},
94 { -1, -1, -1, -1},
95 };
96
97 static struct em28xx_reg_seq zolid_digital[] = {
98 {EM2820_R08_GPIO_CTRL, 0x6a, 0xff, 100},
99 {EM2820_R08_GPIO_CTRL, 0x7a, 0xff, 100},
100 {EM2880_R04_GPO, 0x04, 0xff, 100},
101 {EM2880_R04_GPO, 0x0c, 0xff, 100},
102 { -1, -1, -1, -1},
103 };
104
105
106 static const struct em28xx_reg_seq hauppauge_wintv_hvr_900_analog[] = {
107 {EM2820_R08_GPIO_CTRL, 0x2d, ~EM_GPIO_4, 10},
108 { 0x05, 0xff, 0x10, 10},
109 { -1, -1, -1, -1},
110 };
111
112
113 static const struct em28xx_reg_seq hauppauge_wintv_hvr_900_digital[] = {
114 {EM2820_R08_GPIO_CTRL, 0x2e, ~EM_GPIO_4, 10},
115 {EM2880_R04_GPO, 0x04, 0x0f, 10},
116 {EM2880_R04_GPO, 0x0c, 0x0f, 10},
117 { -1, -1, -1, -1},
118 };
119
120
121 static const struct em28xx_reg_seq hauppauge_wintv_hvr_900R2_digital[] = {
122 {EM2820_R08_GPIO_CTRL, 0x2e, ~EM_GPIO_4, 10},
123 {EM2880_R04_GPO, 0x0c, 0x0f, 10},
124 { -1, -1, -1, -1},
125 };
126
127
128 static const struct em28xx_reg_seq em2880_msi_digivox_ad_analog[] = {
129 {EM2820_R08_GPIO_CTRL, 0x69, ~EM_GPIO_4, 10},
130 { -1, -1, -1, -1},
131 };
132
133
134 static const struct em28xx_reg_seq em2882_kworld_315u_digital[] = {
135 {EM2820_R08_GPIO_CTRL, 0xff, 0xff, 10},
136 {EM2820_R08_GPIO_CTRL, 0xfe, 0xff, 10},
137 {EM2880_R04_GPO, 0x04, 0xff, 10},
138 {EM2880_R04_GPO, 0x0c, 0xff, 10},
139 {EM2820_R08_GPIO_CTRL, 0x7e, 0xff, 10},
140 { -1, -1, -1, -1},
141 };
142
143 static const struct em28xx_reg_seq em2882_kworld_315u_tuner_gpio[] = {
144 {EM2880_R04_GPO, 0x08, 0xff, 10},
145 {EM2880_R04_GPO, 0x0c, 0xff, 10},
146 {EM2880_R04_GPO, 0x08, 0xff, 10},
147 {EM2880_R04_GPO, 0x0c, 0xff, 10},
148 { -1, -1, -1, -1},
149 };
150
151 static const struct em28xx_reg_seq kworld_330u_analog[] = {
152 {EM2820_R08_GPIO_CTRL, 0x6d, ~EM_GPIO_4, 10},
153 {EM2880_R04_GPO, 0x00, 0xff, 10},
154 { -1, -1, -1, -1},
155 };
156
157 static const struct em28xx_reg_seq kworld_330u_digital[] = {
158 {EM2820_R08_GPIO_CTRL, 0x6e, ~EM_GPIO_4, 10},
159 {EM2880_R04_GPO, 0x08, 0xff, 10},
160 { -1, -1, -1, -1},
161 };
162
163
164
165
166
167
168
169
170 static const struct em28xx_reg_seq evga_indtube_analog[] = {
171 {EM2820_R08_GPIO_CTRL, 0x79, 0xff, 60},
172 { -1, -1, -1, -1},
173 };
174
175 static const struct em28xx_reg_seq evga_indtube_digital[] = {
176 {EM2820_R08_GPIO_CTRL, 0x7a, 0xff, 1},
177 {EM2880_R04_GPO, 0x04, 0xff, 10},
178 {EM2880_R04_GPO, 0x0c, 0xff, 1},
179 { -1, -1, -1, -1},
180 };
181
182
183
184
185
186
187
188
189
190
191
192
193 static const struct em28xx_reg_seq kworld_a340_digital[] = {
194 {EM2820_R08_GPIO_CTRL, 0x6d, ~EM_GPIO_4, 10},
195 { -1, -1, -1, -1},
196 };
197
198 static const struct em28xx_reg_seq kworld_ub435q_v3_digital[] = {
199 {EM2874_R80_GPIO_P0_CTRL, 0xff, 0xff, 100},
200 {EM2874_R80_GPIO_P0_CTRL, 0xfe, 0xff, 100},
201 {EM2874_R80_GPIO_P0_CTRL, 0xbe, 0xff, 100},
202 {EM2874_R80_GPIO_P0_CTRL, 0xfe, 0xff, 100},
203 { -1, -1, -1, -1},
204 };
205
206
207 static const struct em28xx_reg_seq pinnacle_hybrid_pro_analog[] = {
208 {EM2820_R08_GPIO_CTRL, 0xfd, ~EM_GPIO_4, 10},
209 { -1, -1, -1, -1},
210 };
211
212 static const struct em28xx_reg_seq pinnacle_hybrid_pro_digital[] = {
213 {EM2820_R08_GPIO_CTRL, 0x6e, ~EM_GPIO_4, 10},
214 {EM2880_R04_GPO, 0x04, 0xff, 100},
215 {EM2880_R04_GPO, 0x0c, 0xff, 1},
216 { -1, -1, -1, -1},
217 };
218
219 static const struct em28xx_reg_seq terratec_cinergy_USB_XS_FR_analog[] = {
220 {EM2820_R08_GPIO_CTRL, 0x6d, ~EM_GPIO_4, 10},
221 {EM2880_R04_GPO, 0x00, 0xff, 10},
222 { -1, -1, -1, -1},
223 };
224
225 static const struct em28xx_reg_seq terratec_cinergy_USB_XS_FR_digital[] = {
226 {EM2820_R08_GPIO_CTRL, 0x6e, ~EM_GPIO_4, 10},
227 {EM2880_R04_GPO, 0x08, 0xff, 10},
228 { -1, -1, -1, -1},
229 };
230
231
232
233
234
235
236
237 static const struct em28xx_reg_seq em2874_pctv_80e_digital[] = {
238 {EM28XX_R06_I2C_CLK, 0x45, 0xff, 10},
239 {EM2874_R80_GPIO_P0_CTRL, 0x00, 0xff, 100},
240 {EM2874_R80_GPIO_P0_CTRL, 0x40, 0xff, 10},
241 { -1, -1, -1, -1},
242 };
243
244
245
246
247
248
249 static const struct em28xx_reg_seq reddo_dvb_c_usb_box[] = {
250 {EM2820_R08_GPIO_CTRL, 0xfe, 0xff, 10},
251 {EM2820_R08_GPIO_CTRL, 0xde, 0xff, 10},
252 {EM2820_R08_GPIO_CTRL, 0xfe, 0xff, 10},
253 {EM2820_R08_GPIO_CTRL, 0xff, 0xff, 10},
254 {EM2820_R08_GPIO_CTRL, 0x7f, 0xff, 10},
255 {EM2820_R08_GPIO_CTRL, 0x6f, 0xff, 10},
256 {EM2820_R08_GPIO_CTRL, 0xff, 0xff, 10},
257 { -1, -1, -1, -1},
258 };
259
260
261 static const struct em28xx_reg_seq default_tuner_gpio[] = {
262 {EM2820_R08_GPIO_CTRL, EM_GPIO_4, EM_GPIO_4, 10},
263 {EM2820_R08_GPIO_CTRL, 0, EM_GPIO_4, 10},
264 {EM2820_R08_GPIO_CTRL, EM_GPIO_4, EM_GPIO_4, 10},
265 { -1, -1, -1, -1},
266 };
267
268
269 static const struct em28xx_reg_seq compro_unmute_tv_gpio[] = {
270 {EM2820_R08_GPIO_CTRL, 5, 7, 10},
271 { -1, -1, -1, -1},
272 };
273
274 static const struct em28xx_reg_seq compro_unmute_svid_gpio[] = {
275 {EM2820_R08_GPIO_CTRL, 4, 7, 10},
276 { -1, -1, -1, -1},
277 };
278
279 static const struct em28xx_reg_seq compro_mute_gpio[] = {
280 {EM2820_R08_GPIO_CTRL, 6, 7, 10},
281 { -1, -1, -1, -1},
282 };
283
284
285 static const struct em28xx_reg_seq terratec_av350_mute_gpio[] = {
286 {EM2820_R08_GPIO_CTRL, 0xff, 0x7f, 10},
287 { -1, -1, -1, -1},
288 };
289
290 static const struct em28xx_reg_seq terratec_av350_unmute_gpio[] = {
291 {EM2820_R08_GPIO_CTRL, 0xff, 0xff, 10},
292 { -1, -1, -1, -1},
293 };
294
295 static const struct em28xx_reg_seq silvercrest_reg_seq[] = {
296 {EM2820_R08_GPIO_CTRL, 0xff, 0xff, 10},
297 {EM2820_R08_GPIO_CTRL, 0x01, 0xf7, 10},
298 { -1, -1, -1, -1},
299 };
300
301 static const struct em28xx_reg_seq vc211a_enable[] = {
302 {EM2820_R08_GPIO_CTRL, 0xff, 0x07, 10},
303 {EM2820_R08_GPIO_CTRL, 0xff, 0x0f, 10},
304 {EM2820_R08_GPIO_CTRL, 0xff, 0x0b, 10},
305 { -1, -1, -1, -1},
306 };
307
308 static const struct em28xx_reg_seq dikom_dk300_digital[] = {
309 {EM2820_R08_GPIO_CTRL, 0x6e, ~EM_GPIO_4, 10},
310 {EM2880_R04_GPO, 0x08, 0xff, 10},
311 { -1, -1, -1, -1},
312 };
313
314
315 static const struct em28xx_reg_seq leadership_digital[] = {
316 {EM2874_R80_GPIO_P0_CTRL, 0x70, 0xff, 10},
317 { -1, -1, -1, -1},
318 };
319
320 static const struct em28xx_reg_seq leadership_reset[] = {
321 {EM2874_R80_GPIO_P0_CTRL, 0xf0, 0xff, 10},
322 {EM2874_R80_GPIO_P0_CTRL, 0xb0, 0xff, 10},
323 {EM2874_R80_GPIO_P0_CTRL, 0xf0, 0xff, 10},
324 { -1, -1, -1, -1},
325 };
326
327
328
329
330
331
332 static const struct em28xx_reg_seq pctv_290e[] = {
333 {EM2874_R80_GPIO_P0_CTRL, 0x00, 0xff, 80},
334 {EM2874_R80_GPIO_P0_CTRL, 0x40, 0xff, 80},
335 {EM2874_R80_GPIO_P0_CTRL, 0xc0, 0xff, 80},
336 { -1, -1, -1, -1},
337 };
338
339 #if 0
340 static const struct em28xx_reg_seq terratec_h5_gpio[] = {
341 {EM2820_R08_GPIO_CTRL, 0xff, 0xff, 10},
342 {EM2874_R80_GPIO_P0_CTRL, 0xf6, 0xff, 100},
343 {EM2874_R80_GPIO_P0_CTRL, 0xf2, 0xff, 50},
344 {EM2874_R80_GPIO_P0_CTRL, 0xf6, 0xff, 50},
345 { -1, -1, -1, -1},
346 };
347
348 static const struct em28xx_reg_seq terratec_h5_digital[] = {
349 {EM2874_R80_GPIO_P0_CTRL, 0xf6, 0xff, 10},
350 {EM2874_R80_GPIO_P0_CTRL, 0xe6, 0xff, 100},
351 {EM2874_R80_GPIO_P0_CTRL, 0xa6, 0xff, 10},
352 { -1, -1, -1, -1},
353 };
354 #endif
355
356
357
358
359
360
361
362
363
364
365
366
367 static const struct em28xx_reg_seq pctv_460e[] = {
368 {EM2874_R80_GPIO_P0_CTRL, 0x01, 0xff, 50},
369 { 0x0d, 0xff, 0xff, 50},
370 {EM2874_R80_GPIO_P0_CTRL, 0x41, 0xff, 50},
371 { 0x0d, 0x42, 0xff, 50},
372 {EM2874_R80_GPIO_P0_CTRL, 0x61, 0xff, 50},
373 { -1, -1, -1, -1},
374 };
375
376 static const struct em28xx_reg_seq c3tech_digital_duo_digital[] = {
377 {EM2874_R80_GPIO_P0_CTRL, 0xff, 0xff, 10},
378 {EM2874_R80_GPIO_P0_CTRL, 0xfd, 0xff, 10},
379 {EM2874_R80_GPIO_P0_CTRL, 0xf9, 0xff, 35},
380 {EM2874_R80_GPIO_P0_CTRL, 0xfd, 0xff, 10},
381 {EM2874_R80_GPIO_P0_CTRL, 0xff, 0xff, 10},
382 {EM2874_R80_GPIO_P0_CTRL, 0xfe, 0xff, 10},
383 {EM2874_R80_GPIO_P0_CTRL, 0xbe, 0xff, 10},
384 {EM2874_R80_GPIO_P0_CTRL, 0xfe, 0xff, 20},
385 { -1, -1, -1, -1},
386 };
387
388
389
390
391
392
393
394
395
396
397
398
399 static const struct em28xx_reg_seq pctv_461e[] = {
400 {EM2874_R80_GPIO_P0_CTRL, 0x7f, 0xff, 0},
401 {0x0d, 0xff, 0xff, 0},
402 {EM2874_R80_GPIO_P0_CTRL, 0x3f, 0xff, 100},
403 {EM2874_R80_GPIO_P0_CTRL, 0x7f, 0xff, 200},
404 {0x0d, 0x42, 0xff, 0},
405 {EM2874_R80_GPIO_P0_CTRL, 0xeb, 0xff, 0},
406 {EM2874_R5F_TS_ENABLE, 0x84, 0x84, 0},
407 { -1, -1, -1, -1},
408 };
409
410 #if 0
411 static const struct em28xx_reg_seq hauppauge_930c_gpio[] = {
412 {EM2874_R80_GPIO_P0_CTRL, 0x6f, 0xff, 10},
413 {EM2874_R80_GPIO_P0_CTRL, 0x4f, 0xff, 10},
414 {EM2874_R80_GPIO_P0_CTRL, 0x6f, 0xff, 10},
415 {EM2874_R80_GPIO_P0_CTRL, 0x4f, 0xff, 10},
416 { -1, -1, -1, -1},
417 };
418
419 static const struct em28xx_reg_seq hauppauge_930c_digital[] = {
420 {EM2874_R80_GPIO_P0_CTRL, 0xf6, 0xff, 10},
421 {EM2874_R80_GPIO_P0_CTRL, 0xe6, 0xff, 100},
422 {EM2874_R80_GPIO_P0_CTRL, 0xa6, 0xff, 10},
423 { -1, -1, -1, -1},
424 };
425 #endif
426
427
428
429
430
431
432
433 static const struct em28xx_reg_seq maxmedia_ub425_tc[] = {
434 {EM2874_R80_GPIO_P0_CTRL, 0x83, 0xff, 100},
435 {EM2874_R80_GPIO_P0_CTRL, 0xc3, 0xff, 100},
436 {EM2874_R80_GPIO_P0_CTRL, 0x43, 0xff, 000},
437 { -1, -1, -1, -1},
438 };
439
440
441
442
443
444
445
446
447 static const struct em28xx_reg_seq pctv_510e[] = {
448 {EM2874_R80_GPIO_P0_CTRL, 0x10, 0xff, 100},
449 {EM2874_R80_GPIO_P0_CTRL, 0x14, 0xff, 100},
450 {EM2874_R80_GPIO_P0_CTRL, 0x54, 0xff, 050},
451 { -1, -1, -1, -1},
452 };
453
454
455
456
457
458
459
460
461 static const struct em28xx_reg_seq pctv_520e[] = {
462 {EM2874_R80_GPIO_P0_CTRL, 0x10, 0xff, 100},
463 {EM2874_R80_GPIO_P0_CTRL, 0x14, 0xff, 100},
464 {EM2874_R80_GPIO_P0_CTRL, 0x54, 0xff, 050},
465 {EM2874_R80_GPIO_P0_CTRL, 0xd4, 0xff, 000},
466 { -1, -1, -1, -1},
467 };
468
469
470
471
472
473
474
475
476
477
478
479 static const struct em28xx_reg_seq speedlink_vad_laplace_reg_seq[] = {
480 {EM2820_R08_GPIO_CTRL, 0xf7, 0xff, 10},
481 {EM2874_R80_GPIO_P0_CTRL, 0xff, 0xb2, 10},
482 { -1, -1, -1, -1},
483 };
484
485 static const struct em28xx_reg_seq pctv_292e[] = {
486 {EM2874_R80_GPIO_P0_CTRL, 0xff, 0xff, 0},
487 {0x0d, 0xff, 0xff, 950},
488 {EM2874_R80_GPIO_P0_CTRL, 0xbd, 0xff, 100},
489 {EM2874_R80_GPIO_P0_CTRL, 0xfd, 0xff, 410},
490 {EM2874_R80_GPIO_P0_CTRL, 0x7d, 0xff, 300},
491 {EM2874_R80_GPIO_P0_CTRL, 0x7c, 0xff, 60},
492 {0x0d, 0x42, 0xff, 50},
493 {EM2874_R5F_TS_ENABLE, 0x85, 0xff, 0},
494 {-1, -1, -1, -1},
495 };
496
497 static const struct em28xx_reg_seq terratec_t2_stick_hd[] = {
498 {EM2874_R80_GPIO_P0_CTRL, 0xff, 0xff, 0},
499 {0x0d, 0xff, 0xff, 600},
500 {EM2874_R80_GPIO_P0_CTRL, 0xfc, 0xff, 10},
501 {EM2874_R80_GPIO_P0_CTRL, 0xbc, 0xff, 100},
502 {EM2874_R80_GPIO_P0_CTRL, 0xfc, 0xff, 100},
503 {EM2874_R80_GPIO_P0_CTRL, 0x00, 0xff, 300},
504 {EM2874_R80_GPIO_P0_CTRL, 0xf8, 0xff, 100},
505 {EM2874_R80_GPIO_P0_CTRL, 0xfc, 0xff, 300},
506 {0x0d, 0x42, 0xff, 1000},
507 {EM2874_R5F_TS_ENABLE, 0x85, 0xff, 0},
508 {-1, -1, -1, -1},
509 };
510
511 static const struct em28xx_reg_seq plex_px_bcud[] = {
512 {EM2874_R80_GPIO_P0_CTRL, 0xff, 0xff, 0},
513 {0x0d, 0xff, 0xff, 0},
514 {EM2874_R50_IR_CONFIG, 0x01, 0xff, 0},
515 {EM28XX_R06_I2C_CLK, 0x40, 0xff, 0},
516 {EM2874_R80_GPIO_P0_CTRL, 0xfd, 0xff, 100},
517 {EM28XX_R12_VINENABLE, 0x20, 0x20, 0},
518 {0x0d, 0x42, 0xff, 1000},
519 {EM2874_R80_GPIO_P0_CTRL, 0xfc, 0xff, 10},
520 {EM2874_R80_GPIO_P0_CTRL, 0xfd, 0xff, 10},
521 {0x73, 0xfd, 0xff, 100},
522 {-1, -1, -1, -1},
523 };
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538 static const struct em28xx_reg_seq hauppauge_dualhd_dvb[] = {
539 {EM2874_R80_GPIO_P0_CTRL, 0xff, 0xff, 0},
540 {0x0d, 0xff, 0xff, 200},
541 {0x50, 0x04, 0xff, 300},
542 {EM2874_R80_GPIO_P0_CTRL, 0xbf, 0xff, 100},
543 {EM2874_R80_GPIO_P0_CTRL, 0xff, 0xff, 100},
544 {EM2874_R80_GPIO_P0_CTRL, 0xdf, 0xff, 100},
545 {EM2874_R80_GPIO_P0_CTRL, 0xff, 0xff, 100},
546 {EM2874_R5F_TS_ENABLE, 0x00, 0xff, 50},
547 {EM2874_R5D_TS1_PKT_SIZE, 0x05, 0xff, 50},
548 {EM2874_R5E_TS2_PKT_SIZE, 0x05, 0xff, 50},
549 {-1, -1, -1, -1},
550 };
551
552
553
554
555 static const struct em28xx_button std_snapshot_button[] = {
556 {
557 .role = EM28XX_BUTTON_SNAPSHOT,
558 .reg_r = EM28XX_R0C_USBSUSP,
559 .reg_clearing = EM28XX_R0C_USBSUSP,
560 .mask = EM28XX_R0C_USBSUSP_SNAPSHOT,
561 .inverted = 0,
562 },
563 {-1, 0, 0, 0, 0},
564 };
565
566 static const struct em28xx_button speedlink_vad_laplace_buttons[] = {
567 {
568 .role = EM28XX_BUTTON_SNAPSHOT,
569 .reg_r = EM2874_R85_GPIO_P1_STATE,
570 .mask = 0x80,
571 .inverted = 1,
572 },
573 {
574 .role = EM28XX_BUTTON_ILLUMINATION,
575 .reg_r = EM2874_R84_GPIO_P0_STATE,
576 .mask = 0x08,
577 .inverted = 1,
578 },
579 {-1, 0, 0, 0, 0},
580 };
581
582
583
584
585 static struct em28xx_led speedlink_vad_laplace_leds[] = {
586 {
587 .role = EM28XX_LED_ANALOG_CAPTURING,
588 .gpio_reg = EM2874_R80_GPIO_P0_CTRL,
589 .gpio_mask = 0x01,
590 .inverted = 1,
591 },
592 {
593 .role = EM28XX_LED_ILLUMINATION,
594 .gpio_reg = EM2874_R80_GPIO_P0_CTRL,
595 .gpio_mask = 0x40,
596 .inverted = 1,
597 },
598 {-1, 0, 0, 0},
599 };
600
601 static struct em28xx_led kworld_ub435q_v3_leds[] = {
602 {
603 .role = EM28XX_LED_DIGITAL_CAPTURING,
604 .gpio_reg = EM2874_R80_GPIO_P0_CTRL,
605 .gpio_mask = 0x80,
606 .inverted = 1,
607 },
608 {-1, 0, 0, 0},
609 };
610
611 static struct em28xx_led pctv_80e_leds[] = {
612 {
613 .role = EM28XX_LED_DIGITAL_CAPTURING,
614 .gpio_reg = EM2874_R80_GPIO_P0_CTRL,
615 .gpio_mask = 0x80,
616 .inverted = 0,
617 },
618 {-1, 0, 0, 0},
619 };
620
621 static struct em28xx_led terratec_grabby_leds[] = {
622 {
623 .role = EM28XX_LED_ANALOG_CAPTURING,
624 .gpio_reg = EM2820_R08_GPIO_CTRL,
625 .gpio_mask = EM_GPIO_3,
626 .inverted = 1,
627 },
628 {-1, 0, 0, 0},
629 };
630
631 static struct em28xx_led hauppauge_dualhd_leds[] = {
632 {
633 .role = EM28XX_LED_DIGITAL_CAPTURING,
634 .gpio_reg = EM2874_R80_GPIO_P0_CTRL,
635 .gpio_mask = EM_GPIO_1,
636 .inverted = 1,
637 },
638 {
639 .role = EM28XX_LED_DIGITAL_CAPTURING_TS2,
640 .gpio_reg = EM2874_R80_GPIO_P0_CTRL,
641 .gpio_mask = EM_GPIO_3,
642 .inverted = 1,
643 },
644 {-1, 0, 0, 0},
645 };
646
647
648
649
650 const struct em28xx_board em28xx_boards[] = {
651 [EM2750_BOARD_UNKNOWN] = {
652 .name = "EM2710/EM2750/EM2751 webcam grabber",
653 .xclk = EM28XX_XCLK_FREQUENCY_20MHZ,
654 .tuner_type = TUNER_ABSENT,
655 .is_webcam = 1,
656 .input = { {
657 .type = EM28XX_VMUX_COMPOSITE,
658 .vmux = 0,
659 .amux = EM28XX_AMUX_VIDEO,
660 .gpio = silvercrest_reg_seq,
661 } },
662 },
663 [EM2800_BOARD_UNKNOWN] = {
664 .name = "Unknown EM2800 video grabber",
665 .is_em2800 = 1,
666 .tda9887_conf = TDA9887_PRESENT,
667 .decoder = EM28XX_SAA711X,
668 .tuner_type = TUNER_ABSENT,
669 .input = { {
670 .type = EM28XX_VMUX_COMPOSITE,
671 .vmux = SAA7115_COMPOSITE0,
672 .amux = EM28XX_AMUX_LINE_IN,
673 }, {
674 .type = EM28XX_VMUX_SVIDEO,
675 .vmux = SAA7115_SVIDEO3,
676 .amux = EM28XX_AMUX_LINE_IN,
677 } },
678 },
679 [EM2820_BOARD_UNKNOWN] = {
680 .name = "Unknown EM2750/28xx video grabber",
681 .tuner_type = TUNER_ABSENT,
682 .is_webcam = 1,
683 },
684 [EM2882_BOARD_ZOLID_HYBRID_TV_STICK] = {
685 .name = ":ZOLID HYBRID TV STICK",
686 .tuner_type = TUNER_XC2028,
687 .tuner_gpio = zolid_tuner,
688 .decoder = EM28XX_TVP5150,
689 .xclk = EM28XX_XCLK_FREQUENCY_12MHZ,
690 .mts_firmware = 1,
691 .has_dvb = 1,
692 .dvb_gpio = zolid_digital,
693 },
694 [EM2750_BOARD_DLCW_130] = {
695
696 .name = "Huaqi DLCW-130",
697 .valid = EM28XX_BOARD_NOT_VALIDATED,
698 .xclk = EM28XX_XCLK_FREQUENCY_48MHZ,
699 .tuner_type = TUNER_ABSENT,
700 .is_webcam = 1,
701 .input = { {
702 .type = EM28XX_VMUX_COMPOSITE,
703 .vmux = 0,
704 .amux = EM28XX_AMUX_VIDEO,
705 } },
706 },
707 [EM2820_BOARD_KWORLD_PVRTV2800RF] = {
708 .name = "Kworld PVR TV 2800 RF",
709 .tuner_type = TUNER_TEMIC_PAL,
710 .tda9887_conf = TDA9887_PRESENT,
711 .decoder = EM28XX_SAA711X,
712 .input = { {
713 .type = EM28XX_VMUX_COMPOSITE,
714 .vmux = SAA7115_COMPOSITE0,
715 .amux = EM28XX_AMUX_LINE_IN,
716 }, {
717 .type = EM28XX_VMUX_SVIDEO,
718 .vmux = SAA7115_SVIDEO3,
719 .amux = EM28XX_AMUX_LINE_IN,
720 } },
721 },
722 [EM2820_BOARD_GADMEI_TVR200] = {
723 .name = "Gadmei TVR200",
724 .tuner_type = TUNER_LG_PAL_NEW_TAPC,
725 .tda9887_conf = TDA9887_PRESENT,
726 .decoder = EM28XX_SAA711X,
727 .input = { {
728 .type = EM28XX_VMUX_TELEVISION,
729 .vmux = SAA7115_COMPOSITE2,
730 .amux = EM28XX_AMUX_LINE_IN,
731 }, {
732 .type = EM28XX_VMUX_COMPOSITE,
733 .vmux = SAA7115_COMPOSITE0,
734 .amux = EM28XX_AMUX_LINE_IN,
735 }, {
736 .type = EM28XX_VMUX_SVIDEO,
737 .vmux = SAA7115_SVIDEO3,
738 .amux = EM28XX_AMUX_LINE_IN,
739 } },
740 },
741 [EM2820_BOARD_TERRATEC_CINERGY_250] = {
742 .name = "Terratec Cinergy 250 USB",
743 .tuner_type = TUNER_LG_PAL_NEW_TAPC,
744 .has_ir_i2c = 1,
745 .tda9887_conf = TDA9887_PRESENT,
746 .decoder = EM28XX_SAA711X,
747 .input = { {
748 .type = EM28XX_VMUX_TELEVISION,
749 .vmux = SAA7115_COMPOSITE2,
750 .amux = EM28XX_AMUX_VIDEO,
751 }, {
752 .type = EM28XX_VMUX_COMPOSITE,
753 .vmux = SAA7115_COMPOSITE0,
754 .amux = EM28XX_AMUX_LINE_IN,
755 }, {
756 .type = EM28XX_VMUX_SVIDEO,
757 .vmux = SAA7115_SVIDEO3,
758 .amux = EM28XX_AMUX_LINE_IN,
759 } },
760 },
761 [EM2820_BOARD_PINNACLE_USB_2] = {
762 .name = "Pinnacle PCTV USB 2",
763 .tuner_type = TUNER_LG_PAL_NEW_TAPC,
764 .has_ir_i2c = 1,
765 .tda9887_conf = TDA9887_PRESENT,
766 .decoder = EM28XX_SAA711X,
767 .input = { {
768 .type = EM28XX_VMUX_TELEVISION,
769 .vmux = SAA7115_COMPOSITE2,
770 .amux = EM28XX_AMUX_VIDEO,
771 }, {
772 .type = EM28XX_VMUX_COMPOSITE,
773 .vmux = SAA7115_COMPOSITE0,
774 .amux = EM28XX_AMUX_LINE_IN,
775 }, {
776 .type = EM28XX_VMUX_SVIDEO,
777 .vmux = SAA7115_SVIDEO3,
778 .amux = EM28XX_AMUX_LINE_IN,
779 } },
780 },
781 [EM2820_BOARD_HAUPPAUGE_WINTV_USB_2] = {
782 .name = "Hauppauge WinTV USB 2",
783 .tuner_type = TUNER_PHILIPS_FM1236_MK3,
784 .tda9887_conf = TDA9887_PRESENT |
785 TDA9887_PORT1_ACTIVE |
786 TDA9887_PORT2_ACTIVE,
787 .decoder = EM28XX_TVP5150,
788 .has_msp34xx = 1,
789 .has_ir_i2c = 1,
790 .input = { {
791 .type = EM28XX_VMUX_TELEVISION,
792 .vmux = TVP5150_COMPOSITE0,
793 .amux = MSP_INPUT_DEFAULT,
794 }, {
795 .type = EM28XX_VMUX_SVIDEO,
796 .vmux = TVP5150_SVIDEO,
797 .amux = MSP_INPUT(MSP_IN_SCART1, MSP_IN_TUNER1,
798 MSP_DSP_IN_SCART, MSP_DSP_IN_SCART),
799 } },
800 },
801 [EM2820_BOARD_DLINK_USB_TV] = {
802 .name = "D-Link DUB-T210 TV Tuner",
803 .valid = EM28XX_BOARD_NOT_VALIDATED,
804 .tuner_type = TUNER_LG_PAL_NEW_TAPC,
805 .tda9887_conf = TDA9887_PRESENT,
806 .decoder = EM28XX_SAA711X,
807 .input = { {
808 .type = EM28XX_VMUX_TELEVISION,
809 .vmux = SAA7115_COMPOSITE2,
810 .amux = EM28XX_AMUX_LINE_IN,
811 }, {
812 .type = EM28XX_VMUX_COMPOSITE,
813 .vmux = SAA7115_COMPOSITE0,
814 .amux = EM28XX_AMUX_LINE_IN,
815 }, {
816 .type = EM28XX_VMUX_SVIDEO,
817 .vmux = SAA7115_SVIDEO3,
818 .amux = EM28XX_AMUX_LINE_IN,
819 } },
820 },
821 [EM2820_BOARD_HERCULES_SMART_TV_USB2] = {
822 .name = "Hercules Smart TV USB 2.0",
823 .valid = EM28XX_BOARD_NOT_VALIDATED,
824 .tuner_type = TUNER_LG_PAL_NEW_TAPC,
825 .tda9887_conf = TDA9887_PRESENT,
826 .decoder = EM28XX_SAA711X,
827 .input = { {
828 .type = EM28XX_VMUX_TELEVISION,
829 .vmux = SAA7115_COMPOSITE2,
830 .amux = EM28XX_AMUX_LINE_IN,
831 }, {
832 .type = EM28XX_VMUX_COMPOSITE,
833 .vmux = SAA7115_COMPOSITE0,
834 .amux = EM28XX_AMUX_LINE_IN,
835 }, {
836 .type = EM28XX_VMUX_SVIDEO,
837 .vmux = SAA7115_SVIDEO3,
838 .amux = EM28XX_AMUX_LINE_IN,
839 } },
840 },
841 [EM2820_BOARD_PINNACLE_USB_2_FM1216ME] = {
842 .name = "Pinnacle PCTV USB 2 (Philips FM1216ME)",
843 .valid = EM28XX_BOARD_NOT_VALIDATED,
844 .tuner_type = TUNER_PHILIPS_FM1216ME_MK3,
845 .tda9887_conf = TDA9887_PRESENT,
846 .decoder = EM28XX_SAA711X,
847 .input = { {
848 .type = EM28XX_VMUX_TELEVISION,
849 .vmux = SAA7115_COMPOSITE2,
850 .amux = EM28XX_AMUX_VIDEO,
851 }, {
852 .type = EM28XX_VMUX_COMPOSITE,
853 .vmux = SAA7115_COMPOSITE0,
854 .amux = EM28XX_AMUX_LINE_IN,
855 }, {
856 .type = EM28XX_VMUX_SVIDEO,
857 .vmux = SAA7115_SVIDEO3,
858 .amux = EM28XX_AMUX_LINE_IN,
859 } },
860 },
861 [EM2820_BOARD_GADMEI_UTV310] = {
862 .name = "Gadmei UTV310",
863 .valid = EM28XX_BOARD_NOT_VALIDATED,
864 .tuner_type = TUNER_TNF_5335MF,
865 .tda9887_conf = TDA9887_PRESENT,
866 .decoder = EM28XX_SAA711X,
867 .input = { {
868 .type = EM28XX_VMUX_TELEVISION,
869 .vmux = SAA7115_COMPOSITE1,
870 .amux = EM28XX_AMUX_LINE_IN,
871 }, {
872 .type = EM28XX_VMUX_COMPOSITE,
873 .vmux = SAA7115_COMPOSITE0,
874 .amux = EM28XX_AMUX_LINE_IN,
875 }, {
876 .type = EM28XX_VMUX_SVIDEO,
877 .vmux = SAA7115_SVIDEO3,
878 .amux = EM28XX_AMUX_LINE_IN,
879 } },
880 },
881 [EM2820_BOARD_LEADTEK_WINFAST_USBII_DELUXE] = {
882 .name = "Leadtek Winfast USB II Deluxe",
883 .valid = EM28XX_BOARD_NOT_VALIDATED,
884 .tuner_type = TUNER_PHILIPS_FM1216ME_MK3,
885 .has_ir_i2c = 1,
886 .tvaudio_addr = 0x58,
887 .tda9887_conf = TDA9887_PRESENT |
888 TDA9887_PORT2_ACTIVE |
889 TDA9887_QSS,
890 .decoder = EM28XX_SAA711X,
891 .adecoder = EM28XX_TVAUDIO,
892 .input = { {
893 .type = EM28XX_VMUX_TELEVISION,
894 .vmux = SAA7115_COMPOSITE4,
895 .amux = EM28XX_AMUX_AUX,
896 }, {
897 .type = EM28XX_VMUX_COMPOSITE,
898 .vmux = SAA7115_COMPOSITE5,
899 .amux = EM28XX_AMUX_LINE_IN,
900 }, {
901 .type = EM28XX_VMUX_SVIDEO,
902 .vmux = SAA7115_SVIDEO3,
903 .amux = EM28XX_AMUX_LINE_IN,
904 } },
905 .radio = {
906 .type = EM28XX_RADIO,
907 .amux = EM28XX_AMUX_AUX,
908 }
909 },
910 [EM2820_BOARD_VIDEOLOGY_20K14XUSB] = {
911 .name = "Videology 20K14XUSB USB2.0",
912 .valid = EM28XX_BOARD_NOT_VALIDATED,
913 .tuner_type = TUNER_ABSENT,
914 .is_webcam = 1,
915 .input = { {
916 .type = EM28XX_VMUX_COMPOSITE,
917 .vmux = 0,
918 .amux = EM28XX_AMUX_VIDEO,
919 } },
920 },
921 [EM2820_BOARD_SILVERCREST_WEBCAM] = {
922 .name = "Silvercrest Webcam 1.3mpix",
923 .tuner_type = TUNER_ABSENT,
924 .is_webcam = 1,
925 .input = { {
926 .type = EM28XX_VMUX_COMPOSITE,
927 .vmux = 0,
928 .amux = EM28XX_AMUX_VIDEO,
929 .gpio = silvercrest_reg_seq,
930 } },
931 },
932 [EM2821_BOARD_SUPERCOMP_USB_2] = {
933 .name = "Supercomp USB 2.0 TV",
934 .valid = EM28XX_BOARD_NOT_VALIDATED,
935 .tuner_type = TUNER_PHILIPS_FM1236_MK3,
936 .tda9887_conf = TDA9887_PRESENT |
937 TDA9887_PORT1_ACTIVE |
938 TDA9887_PORT2_ACTIVE,
939 .decoder = EM28XX_SAA711X,
940 .input = { {
941 .type = EM28XX_VMUX_TELEVISION,
942 .vmux = SAA7115_COMPOSITE2,
943 .amux = EM28XX_AMUX_LINE_IN,
944 }, {
945 .type = EM28XX_VMUX_COMPOSITE,
946 .vmux = SAA7115_COMPOSITE0,
947 .amux = EM28XX_AMUX_VIDEO,
948 }, {
949 .type = EM28XX_VMUX_SVIDEO,
950 .vmux = SAA7115_SVIDEO3,
951 .amux = EM28XX_AMUX_LINE_IN,
952 } },
953 },
954 [EM2821_BOARD_USBGEAR_VD204] = {
955 .name = "Usbgear VD204v9",
956 .valid = EM28XX_BOARD_NOT_VALIDATED,
957 .tuner_type = TUNER_ABSENT,
958 .decoder = EM28XX_SAA711X,
959 .input = { {
960 .type = EM28XX_VMUX_COMPOSITE,
961 .vmux = SAA7115_COMPOSITE0,
962 .amux = EM28XX_AMUX_LINE_IN,
963 }, {
964 .type = EM28XX_VMUX_SVIDEO,
965 .vmux = SAA7115_SVIDEO3,
966 .amux = EM28XX_AMUX_LINE_IN,
967 } },
968 },
969 [EM2860_BOARD_NETGMBH_CAM] = {
970
971 .name = "NetGMBH Cam",
972 .valid = EM28XX_BOARD_NOT_VALIDATED,
973 .tuner_type = TUNER_ABSENT,
974 .is_webcam = 1,
975 .input = { {
976 .type = EM28XX_VMUX_COMPOSITE,
977 .vmux = 0,
978 .amux = EM28XX_AMUX_VIDEO,
979 } },
980 },
981 [EM2860_BOARD_TYPHOON_DVD_MAKER] = {
982 .name = "Typhoon DVD Maker",
983 .decoder = EM28XX_SAA711X,
984 .tuner_type = TUNER_ABSENT,
985 .input = { {
986 .type = EM28XX_VMUX_COMPOSITE,
987 .vmux = SAA7115_COMPOSITE0,
988 .amux = EM28XX_AMUX_LINE_IN,
989 }, {
990 .type = EM28XX_VMUX_SVIDEO,
991 .vmux = SAA7115_SVIDEO3,
992 .amux = EM28XX_AMUX_LINE_IN,
993 } },
994 },
995 [EM2860_BOARD_GADMEI_UTV330] = {
996 .name = "Gadmei UTV330",
997 .valid = EM28XX_BOARD_NOT_VALIDATED,
998 .tuner_type = TUNER_TNF_5335MF,
999 .tda9887_conf = TDA9887_PRESENT,
1000 .decoder = EM28XX_SAA711X,
1001 .input = { {
1002 .type = EM28XX_VMUX_TELEVISION,
1003 .vmux = SAA7115_COMPOSITE2,
1004 .amux = EM28XX_AMUX_VIDEO,
1005 }, {
1006 .type = EM28XX_VMUX_COMPOSITE,
1007 .vmux = SAA7115_COMPOSITE0,
1008 .amux = EM28XX_AMUX_LINE_IN,
1009 }, {
1010 .type = EM28XX_VMUX_SVIDEO,
1011 .vmux = SAA7115_SVIDEO3,
1012 .amux = EM28XX_AMUX_LINE_IN,
1013 } },
1014 },
1015 [EM2861_BOARD_GADMEI_UTV330PLUS] = {
1016 .name = "Gadmei UTV330+",
1017 .tuner_type = TUNER_TNF_5335MF,
1018 .tda9887_conf = TDA9887_PRESENT,
1019 .ir_codes = RC_MAP_GADMEI_RM008Z,
1020 .decoder = EM28XX_SAA711X,
1021 .xclk = EM28XX_XCLK_FREQUENCY_12MHZ,
1022 .input = { {
1023 .type = EM28XX_VMUX_TELEVISION,
1024 .vmux = SAA7115_COMPOSITE2,
1025 .amux = EM28XX_AMUX_VIDEO,
1026 }, {
1027 .type = EM28XX_VMUX_COMPOSITE,
1028 .vmux = SAA7115_COMPOSITE0,
1029 .amux = EM28XX_AMUX_LINE_IN,
1030 }, {
1031 .type = EM28XX_VMUX_SVIDEO,
1032 .vmux = SAA7115_SVIDEO3,
1033 .amux = EM28XX_AMUX_LINE_IN,
1034 } },
1035 },
1036 [EM2860_BOARD_TERRATEC_HYBRID_XS] = {
1037 .name = "Terratec Cinergy A Hybrid XS",
1038 .valid = EM28XX_BOARD_NOT_VALIDATED,
1039 .tuner_type = TUNER_XC2028,
1040 .tuner_gpio = default_tuner_gpio,
1041 .decoder = EM28XX_TVP5150,
1042
1043 .input = { {
1044 .type = EM28XX_VMUX_TELEVISION,
1045 .vmux = TVP5150_COMPOSITE0,
1046 .amux = EM28XX_AMUX_VIDEO,
1047 .gpio = hauppauge_wintv_hvr_900_analog,
1048 }, {
1049 .type = EM28XX_VMUX_COMPOSITE,
1050 .vmux = TVP5150_COMPOSITE1,
1051 .amux = EM28XX_AMUX_LINE_IN,
1052 .gpio = hauppauge_wintv_hvr_900_analog,
1053 }, {
1054 .type = EM28XX_VMUX_SVIDEO,
1055 .vmux = TVP5150_SVIDEO,
1056 .amux = EM28XX_AMUX_LINE_IN,
1057 .gpio = hauppauge_wintv_hvr_900_analog,
1058 } },
1059 },
1060 [EM2861_BOARD_KWORLD_PVRTV_300U] = {
1061 .name = "KWorld PVRTV 300U",
1062 .valid = EM28XX_BOARD_NOT_VALIDATED,
1063 .tuner_type = TUNER_XC2028,
1064 .tuner_gpio = default_tuner_gpio,
1065 .decoder = EM28XX_TVP5150,
1066 .input = { {
1067 .type = EM28XX_VMUX_TELEVISION,
1068 .vmux = TVP5150_COMPOSITE0,
1069 .amux = EM28XX_AMUX_VIDEO,
1070 }, {
1071 .type = EM28XX_VMUX_COMPOSITE,
1072 .vmux = TVP5150_COMPOSITE1,
1073 .amux = EM28XX_AMUX_LINE_IN,
1074 }, {
1075 .type = EM28XX_VMUX_SVIDEO,
1076 .vmux = TVP5150_SVIDEO,
1077 .amux = EM28XX_AMUX_LINE_IN,
1078 } },
1079 },
1080 [EM2861_BOARD_YAKUMO_MOVIE_MIXER] = {
1081 .name = "Yakumo MovieMixer",
1082 .tuner_type = TUNER_ABSENT,
1083 .decoder = EM28XX_TVP5150,
1084 .input = { {
1085 .type = EM28XX_VMUX_TELEVISION,
1086 .vmux = TVP5150_COMPOSITE0,
1087 .amux = EM28XX_AMUX_VIDEO,
1088 }, {
1089 .type = EM28XX_VMUX_COMPOSITE,
1090 .vmux = TVP5150_COMPOSITE1,
1091 .amux = EM28XX_AMUX_LINE_IN,
1092 }, {
1093 .type = EM28XX_VMUX_SVIDEO,
1094 .vmux = TVP5150_SVIDEO,
1095 .amux = EM28XX_AMUX_LINE_IN,
1096 } },
1097 },
1098 [EM2860_BOARD_TVP5150_REFERENCE_DESIGN] = {
1099 .name = "EM2860/TVP5150 Reference Design",
1100 .tuner_type = TUNER_ABSENT,
1101 .decoder = EM28XX_TVP5150,
1102 .input = { {
1103 .type = EM28XX_VMUX_COMPOSITE,
1104 .vmux = TVP5150_COMPOSITE1,
1105 .amux = EM28XX_AMUX_LINE_IN,
1106 }, {
1107 .type = EM28XX_VMUX_SVIDEO,
1108 .vmux = TVP5150_SVIDEO,
1109 .amux = EM28XX_AMUX_LINE_IN,
1110 } },
1111 },
1112 [EM2861_BOARD_PLEXTOR_PX_TV100U] = {
1113 .name = "Plextor ConvertX PX-TV100U",
1114 .tuner_type = TUNER_TNF_5335MF,
1115 .xclk = EM28XX_XCLK_I2S_MSB_TIMING |
1116 EM28XX_XCLK_FREQUENCY_12MHZ,
1117 .tda9887_conf = TDA9887_PRESENT,
1118 .decoder = EM28XX_TVP5150,
1119 .has_msp34xx = 1,
1120 .input = { {
1121 .type = EM28XX_VMUX_TELEVISION,
1122 .vmux = TVP5150_COMPOSITE0,
1123 .amux = EM28XX_AMUX_LINE_IN,
1124 .gpio = pinnacle_hybrid_pro_analog,
1125 }, {
1126 .type = EM28XX_VMUX_COMPOSITE,
1127 .vmux = TVP5150_COMPOSITE1,
1128 .amux = EM28XX_AMUX_LINE_IN,
1129 .gpio = pinnacle_hybrid_pro_analog,
1130 }, {
1131 .type = EM28XX_VMUX_SVIDEO,
1132 .vmux = TVP5150_SVIDEO,
1133 .amux = EM28XX_AMUX_LINE_IN,
1134 .gpio = pinnacle_hybrid_pro_analog,
1135 } },
1136 },
1137
1138
1139
1140 [EM2870_BOARD_TERRATEC_XS] = {
1141 .name = "Terratec Cinergy T XS",
1142 .valid = EM28XX_BOARD_NOT_VALIDATED,
1143 .tuner_type = TUNER_XC2028,
1144 .tuner_gpio = default_tuner_gpio,
1145 },
1146 [EM2870_BOARD_TERRATEC_XS_MT2060] = {
1147 .name = "Terratec Cinergy T XS (MT2060)",
1148 .xclk = EM28XX_XCLK_IR_RC5_MODE |
1149 EM28XX_XCLK_FREQUENCY_12MHZ,
1150 .i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE,
1151 .tuner_type = TUNER_ABSENT,
1152 .has_dvb = 1,
1153 .tuner_gpio = default_tuner_gpio,
1154 },
1155 [EM2870_BOARD_KWORLD_350U] = {
1156 .name = "Kworld 350 U DVB-T",
1157 .valid = EM28XX_BOARD_NOT_VALIDATED,
1158 .tuner_type = TUNER_XC2028,
1159 .tuner_gpio = default_tuner_gpio,
1160 },
1161 [EM2870_BOARD_KWORLD_355U] = {
1162 .name = "Kworld 355 U DVB-T",
1163 .valid = EM28XX_BOARD_NOT_VALIDATED,
1164 .tuner_type = TUNER_ABSENT,
1165 .tuner_gpio = default_tuner_gpio,
1166 .has_dvb = 1,
1167 .dvb_gpio = default_digital,
1168 },
1169 [EM2870_BOARD_PINNACLE_PCTV_DVB] = {
1170 .name = "Pinnacle PCTV DVB-T",
1171 .valid = EM28XX_BOARD_NOT_VALIDATED,
1172 .tuner_type = TUNER_ABSENT,
1173
1174 .xclk = EM28XX_XCLK_IR_RC5_MODE |
1175 EM28XX_XCLK_FREQUENCY_10MHZ,
1176 },
1177 [EM2870_BOARD_COMPRO_VIDEOMATE] = {
1178 .name = "Compro, VideoMate U3",
1179 .valid = EM28XX_BOARD_NOT_VALIDATED,
1180 .tuner_type = TUNER_ABSENT,
1181 },
1182
1183 [EM2880_BOARD_TERRATEC_HYBRID_XS_FR] = {
1184 .name = "Terratec Hybrid XS Secam",
1185 .has_msp34xx = 1,
1186 .tuner_type = TUNER_XC2028,
1187 .tuner_gpio = default_tuner_gpio,
1188 .decoder = EM28XX_TVP5150,
1189 .has_dvb = 1,
1190 .dvb_gpio = terratec_cinergy_USB_XS_FR_digital,
1191 .input = { {
1192 .type = EM28XX_VMUX_TELEVISION,
1193 .vmux = TVP5150_COMPOSITE0,
1194 .amux = EM28XX_AMUX_VIDEO,
1195 .gpio = terratec_cinergy_USB_XS_FR_analog,
1196 }, {
1197 .type = EM28XX_VMUX_COMPOSITE,
1198 .vmux = TVP5150_COMPOSITE1,
1199 .amux = EM28XX_AMUX_LINE_IN,
1200 .gpio = terratec_cinergy_USB_XS_FR_analog,
1201 }, {
1202 .type = EM28XX_VMUX_SVIDEO,
1203 .vmux = TVP5150_SVIDEO,
1204 .amux = EM28XX_AMUX_LINE_IN,
1205 .gpio = terratec_cinergy_USB_XS_FR_analog,
1206 } },
1207 },
1208 [EM2884_BOARD_TERRATEC_H5] = {
1209 .name = "Terratec Cinergy H5",
1210 .has_dvb = 1,
1211 #if 0
1212 .tuner_type = TUNER_PHILIPS_TDA8290,
1213 .tuner_addr = 0x41,
1214 .dvb_gpio = terratec_h5_digital,
1215 .tuner_gpio = terratec_h5_gpio,
1216 #else
1217 .tuner_type = TUNER_ABSENT,
1218 #endif
1219 .def_i2c_bus = 1,
1220 .i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
1221 EM28XX_I2C_FREQ_400_KHZ,
1222 },
1223 [EM2884_BOARD_TERRATEC_H6] = {
1224 .name = "Terratec Cinergy H6 rev. 2",
1225 .has_dvb = 1,
1226 .ir_codes = RC_MAP_NEC_TERRATEC_CINERGY_XS,
1227 #if 0
1228 .tuner_type = TUNER_PHILIPS_TDA8290,
1229 .tuner_addr = 0x41,
1230 .dvb_gpio = terratec_h5_digital,
1231 .tuner_gpio = terratec_h5_gpio,
1232 #else
1233 .tuner_type = TUNER_ABSENT,
1234 #endif
1235 .def_i2c_bus = 1,
1236 .i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
1237 EM28XX_I2C_FREQ_400_KHZ,
1238 },
1239 [EM2884_BOARD_HAUPPAUGE_WINTV_HVR_930C] = {
1240 .name = "Hauppauge WinTV HVR 930C",
1241 .has_dvb = 1,
1242 #if 0
1243 .tuner_type = TUNER_XC5000,
1244 .tuner_addr = 0x41,
1245 .dvb_gpio = hauppauge_930c_digital,
1246 .tuner_gpio = hauppauge_930c_gpio,
1247 #else
1248 .tuner_type = TUNER_ABSENT,
1249 #endif
1250 .ir_codes = RC_MAP_HAUPPAUGE,
1251 .def_i2c_bus = 1,
1252 .i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
1253 EM28XX_I2C_FREQ_400_KHZ,
1254 },
1255 [EM2884_BOARD_C3TECH_DIGITAL_DUO] = {
1256 .name = "C3 Tech Digital Duo HDTV/SDTV USB",
1257 .has_dvb = 1,
1258
1259 .tuner_type = TUNER_ABSENT,
1260 .ir_codes = RC_MAP_EMPTY,
1261 .def_i2c_bus = 1,
1262 .i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE,
1263 .dvb_gpio = c3tech_digital_duo_digital,
1264 },
1265 [EM2884_BOARD_CINERGY_HTC_STICK] = {
1266 .name = "Terratec Cinergy HTC Stick",
1267 .has_dvb = 1,
1268 .ir_codes = RC_MAP_NEC_TERRATEC_CINERGY_XS,
1269 .tuner_type = TUNER_ABSENT,
1270 .def_i2c_bus = 1,
1271 .i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
1272 EM28XX_I2C_FREQ_400_KHZ,
1273 },
1274 [EM2884_BOARD_ELGATO_EYETV_HYBRID_2008] = {
1275 .name = "Elgato EyeTV Hybrid 2008 INT",
1276 .has_dvb = 1,
1277 .ir_codes = RC_MAP_NEC_TERRATEC_CINERGY_XS,
1278 .tuner_type = TUNER_ABSENT,
1279 .def_i2c_bus = 1,
1280 .i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
1281 EM28XX_I2C_FREQ_400_KHZ,
1282 },
1283 [EM2880_BOARD_HAUPPAUGE_WINTV_HVR_900] = {
1284 .name = "Hauppauge WinTV HVR 900",
1285 .tda9887_conf = TDA9887_PRESENT,
1286 .tuner_type = TUNER_XC2028,
1287 .tuner_gpio = default_tuner_gpio,
1288 .mts_firmware = 1,
1289 .has_dvb = 1,
1290 .dvb_gpio = hauppauge_wintv_hvr_900_digital,
1291 .ir_codes = RC_MAP_HAUPPAUGE,
1292 .decoder = EM28XX_TVP5150,
1293 .input = { {
1294 .type = EM28XX_VMUX_TELEVISION,
1295 .vmux = TVP5150_COMPOSITE0,
1296 .amux = EM28XX_AMUX_VIDEO,
1297 .gpio = hauppauge_wintv_hvr_900_analog,
1298 }, {
1299 .type = EM28XX_VMUX_COMPOSITE,
1300 .vmux = TVP5150_COMPOSITE1,
1301 .amux = EM28XX_AMUX_LINE_IN,
1302 .gpio = hauppauge_wintv_hvr_900_analog,
1303 }, {
1304 .type = EM28XX_VMUX_SVIDEO,
1305 .vmux = TVP5150_SVIDEO,
1306 .amux = EM28XX_AMUX_LINE_IN,
1307 .gpio = hauppauge_wintv_hvr_900_analog,
1308 } },
1309 },
1310 [EM2880_BOARD_HAUPPAUGE_WINTV_HVR_900_R2] = {
1311 .name = "Hauppauge WinTV HVR 900 (R2)",
1312 .tda9887_conf = TDA9887_PRESENT,
1313 .tuner_type = TUNER_XC2028,
1314 .tuner_gpio = default_tuner_gpio,
1315 .mts_firmware = 1,
1316 .has_dvb = 1,
1317 .dvb_gpio = hauppauge_wintv_hvr_900R2_digital,
1318 .ir_codes = RC_MAP_HAUPPAUGE,
1319 .decoder = EM28XX_TVP5150,
1320 .input = { {
1321 .type = EM28XX_VMUX_TELEVISION,
1322 .vmux = TVP5150_COMPOSITE0,
1323 .amux = EM28XX_AMUX_VIDEO,
1324 .gpio = hauppauge_wintv_hvr_900_analog,
1325 }, {
1326 .type = EM28XX_VMUX_COMPOSITE,
1327 .vmux = TVP5150_COMPOSITE1,
1328 .amux = EM28XX_AMUX_LINE_IN,
1329 .gpio = hauppauge_wintv_hvr_900_analog,
1330 }, {
1331 .type = EM28XX_VMUX_SVIDEO,
1332 .vmux = TVP5150_SVIDEO,
1333 .amux = EM28XX_AMUX_LINE_IN,
1334 .gpio = hauppauge_wintv_hvr_900_analog,
1335 } },
1336 },
1337 [EM2883_BOARD_HAUPPAUGE_WINTV_HVR_850] = {
1338 .name = "Hauppauge WinTV HVR 850",
1339 .tuner_type = TUNER_XC2028,
1340 .tuner_gpio = default_tuner_gpio,
1341 .mts_firmware = 1,
1342 .has_dvb = 1,
1343 .dvb_gpio = hauppauge_wintv_hvr_900_digital,
1344 .ir_codes = RC_MAP_HAUPPAUGE,
1345 .decoder = EM28XX_TVP5150,
1346 .input = { {
1347 .type = EM28XX_VMUX_TELEVISION,
1348 .vmux = TVP5150_COMPOSITE0,
1349 .amux = EM28XX_AMUX_VIDEO,
1350 .gpio = hauppauge_wintv_hvr_900_analog,
1351 }, {
1352 .type = EM28XX_VMUX_COMPOSITE,
1353 .vmux = TVP5150_COMPOSITE1,
1354 .amux = EM28XX_AMUX_LINE_IN,
1355 .gpio = hauppauge_wintv_hvr_900_analog,
1356 }, {
1357 .type = EM28XX_VMUX_SVIDEO,
1358 .vmux = TVP5150_SVIDEO,
1359 .amux = EM28XX_AMUX_LINE_IN,
1360 .gpio = hauppauge_wintv_hvr_900_analog,
1361 } },
1362 },
1363 [EM2883_BOARD_HAUPPAUGE_WINTV_HVR_950] = {
1364 .name = "Hauppauge WinTV HVR 950",
1365 .tuner_type = TUNER_XC2028,
1366 .tuner_gpio = default_tuner_gpio,
1367 .mts_firmware = 1,
1368 .has_dvb = 1,
1369 .dvb_gpio = hauppauge_wintv_hvr_900_digital,
1370 .ir_codes = RC_MAP_HAUPPAUGE,
1371 .decoder = EM28XX_TVP5150,
1372 .input = { {
1373 .type = EM28XX_VMUX_TELEVISION,
1374 .vmux = TVP5150_COMPOSITE0,
1375 .amux = EM28XX_AMUX_VIDEO,
1376 .gpio = hauppauge_wintv_hvr_900_analog,
1377 }, {
1378 .type = EM28XX_VMUX_COMPOSITE,
1379 .vmux = TVP5150_COMPOSITE1,
1380 .amux = EM28XX_AMUX_LINE_IN,
1381 .gpio = hauppauge_wintv_hvr_900_analog,
1382 }, {
1383 .type = EM28XX_VMUX_SVIDEO,
1384 .vmux = TVP5150_SVIDEO,
1385 .amux = EM28XX_AMUX_LINE_IN,
1386 .gpio = hauppauge_wintv_hvr_900_analog,
1387 } },
1388 },
1389 [EM2880_BOARD_PINNACLE_PCTV_HD_PRO] = {
1390 .name = "Pinnacle PCTV HD Pro Stick",
1391 .tuner_type = TUNER_XC2028,
1392 .tuner_gpio = default_tuner_gpio,
1393 .mts_firmware = 1,
1394 .has_dvb = 1,
1395 .dvb_gpio = hauppauge_wintv_hvr_900_digital,
1396 .ir_codes = RC_MAP_PINNACLE_PCTV_HD,
1397 .decoder = EM28XX_TVP5150,
1398 .input = { {
1399 .type = EM28XX_VMUX_TELEVISION,
1400 .vmux = TVP5150_COMPOSITE0,
1401 .amux = EM28XX_AMUX_VIDEO,
1402 .gpio = hauppauge_wintv_hvr_900_analog,
1403 }, {
1404 .type = EM28XX_VMUX_COMPOSITE,
1405 .vmux = TVP5150_COMPOSITE1,
1406 .amux = EM28XX_AMUX_LINE_IN,
1407 .gpio = hauppauge_wintv_hvr_900_analog,
1408 }, {
1409 .type = EM28XX_VMUX_SVIDEO,
1410 .vmux = TVP5150_SVIDEO,
1411 .amux = EM28XX_AMUX_LINE_IN,
1412 .gpio = hauppauge_wintv_hvr_900_analog,
1413 } },
1414 },
1415 [EM2880_BOARD_AMD_ATI_TV_WONDER_HD_600] = {
1416 .name = "AMD ATI TV Wonder HD 600",
1417 .tuner_type = TUNER_XC2028,
1418 .tuner_gpio = default_tuner_gpio,
1419 .mts_firmware = 1,
1420 .has_dvb = 1,
1421 .dvb_gpio = hauppauge_wintv_hvr_900_digital,
1422 .ir_codes = RC_MAP_ATI_TV_WONDER_HD_600,
1423 .decoder = EM28XX_TVP5150,
1424 .input = { {
1425 .type = EM28XX_VMUX_TELEVISION,
1426 .vmux = TVP5150_COMPOSITE0,
1427 .amux = EM28XX_AMUX_VIDEO,
1428 .gpio = hauppauge_wintv_hvr_900_analog,
1429 }, {
1430 .type = EM28XX_VMUX_COMPOSITE,
1431 .vmux = TVP5150_COMPOSITE1,
1432 .amux = EM28XX_AMUX_LINE_IN,
1433 .gpio = hauppauge_wintv_hvr_900_analog,
1434 }, {
1435 .type = EM28XX_VMUX_SVIDEO,
1436 .vmux = TVP5150_SVIDEO,
1437 .amux = EM28XX_AMUX_LINE_IN,
1438 .gpio = hauppauge_wintv_hvr_900_analog,
1439 } },
1440 },
1441 [EM2880_BOARD_TERRATEC_HYBRID_XS] = {
1442 .name = "Terratec Hybrid XS",
1443 .tuner_type = TUNER_XC2028,
1444 .tuner_gpio = default_tuner_gpio,
1445 .decoder = EM28XX_TVP5150,
1446 .has_dvb = 1,
1447 .dvb_gpio = default_digital,
1448 .ir_codes = RC_MAP_TERRATEC_CINERGY_XS,
1449 .xclk = EM28XX_XCLK_FREQUENCY_12MHZ,
1450 .input = { {
1451 .type = EM28XX_VMUX_TELEVISION,
1452 .vmux = TVP5150_COMPOSITE0,
1453 .amux = EM28XX_AMUX_VIDEO,
1454 .gpio = default_analog,
1455 }, {
1456 .type = EM28XX_VMUX_COMPOSITE,
1457 .vmux = TVP5150_COMPOSITE1,
1458 .amux = EM28XX_AMUX_LINE_IN,
1459 .gpio = default_analog,
1460 }, {
1461 .type = EM28XX_VMUX_SVIDEO,
1462 .vmux = TVP5150_SVIDEO,
1463 .amux = EM28XX_AMUX_LINE_IN,
1464 .gpio = default_analog,
1465 } },
1466 },
1467
1468
1469
1470
1471
1472 [EM2880_BOARD_TERRATEC_PRODIGY_XS] = {
1473 .name = "Terratec Prodigy XS",
1474 .tuner_type = TUNER_XC2028,
1475 .tuner_gpio = default_tuner_gpio,
1476 .decoder = EM28XX_TVP5150,
1477 .input = { {
1478 .type = EM28XX_VMUX_TELEVISION,
1479 .vmux = TVP5150_COMPOSITE0,
1480 .amux = EM28XX_AMUX_VIDEO,
1481 .gpio = hauppauge_wintv_hvr_900_analog,
1482 }, {
1483 .type = EM28XX_VMUX_COMPOSITE,
1484 .vmux = TVP5150_COMPOSITE1,
1485 .amux = EM28XX_AMUX_LINE_IN,
1486 .gpio = hauppauge_wintv_hvr_900_analog,
1487 }, {
1488 .type = EM28XX_VMUX_SVIDEO,
1489 .vmux = TVP5150_SVIDEO,
1490 .amux = EM28XX_AMUX_LINE_IN,
1491 .gpio = hauppauge_wintv_hvr_900_analog,
1492 } },
1493 },
1494 [EM2820_BOARD_MSI_VOX_USB_2] = {
1495 .name = "MSI VOX USB 2.0",
1496 .tuner_type = TUNER_LG_PAL_NEW_TAPC,
1497 .tda9887_conf = TDA9887_PRESENT |
1498 TDA9887_PORT1_ACTIVE |
1499 TDA9887_PORT2_ACTIVE,
1500 .max_range_640_480 = 1,
1501 .decoder = EM28XX_SAA711X,
1502 .input = { {
1503 .type = EM28XX_VMUX_TELEVISION,
1504 .vmux = SAA7115_COMPOSITE4,
1505 .amux = EM28XX_AMUX_VIDEO,
1506 }, {
1507 .type = EM28XX_VMUX_COMPOSITE,
1508 .vmux = SAA7115_COMPOSITE0,
1509 .amux = EM28XX_AMUX_LINE_IN,
1510 }, {
1511 .type = EM28XX_VMUX_SVIDEO,
1512 .vmux = SAA7115_SVIDEO3,
1513 .amux = EM28XX_AMUX_LINE_IN,
1514 } },
1515 },
1516 [EM2800_BOARD_TERRATEC_CINERGY_200] = {
1517 .name = "Terratec Cinergy 200 USB",
1518 .is_em2800 = 1,
1519 .has_ir_i2c = 1,
1520 .tuner_type = TUNER_LG_TALN,
1521 .tda9887_conf = TDA9887_PRESENT,
1522 .decoder = EM28XX_SAA711X,
1523 .input = { {
1524 .type = EM28XX_VMUX_TELEVISION,
1525 .vmux = SAA7115_COMPOSITE2,
1526 .amux = EM28XX_AMUX_VIDEO,
1527 }, {
1528 .type = EM28XX_VMUX_COMPOSITE,
1529 .vmux = SAA7115_COMPOSITE0,
1530 .amux = EM28XX_AMUX_LINE_IN,
1531 }, {
1532 .type = EM28XX_VMUX_SVIDEO,
1533 .vmux = SAA7115_SVIDEO3,
1534 .amux = EM28XX_AMUX_LINE_IN,
1535 } },
1536 },
1537 [EM2800_BOARD_GRABBEEX_USB2800] = {
1538 .name = "eMPIA Technology, Inc. GrabBeeX+ Video Encoder",
1539 .is_em2800 = 1,
1540 .decoder = EM28XX_SAA711X,
1541 .tuner_type = TUNER_ABSENT,
1542 .input = { {
1543 .type = EM28XX_VMUX_COMPOSITE,
1544 .vmux = SAA7115_COMPOSITE0,
1545 .amux = EM28XX_AMUX_LINE_IN,
1546 }, {
1547 .type = EM28XX_VMUX_SVIDEO,
1548 .vmux = SAA7115_SVIDEO3,
1549 .amux = EM28XX_AMUX_LINE_IN,
1550 } },
1551 },
1552 [EM2800_BOARD_VC211A] = {
1553 .name = "Actionmaster/LinXcel/Digitus VC211A",
1554 .is_em2800 = 1,
1555 .tuner_type = TUNER_ABSENT,
1556 .decoder = EM28XX_SAA711X,
1557 .input = { {
1558 .type = EM28XX_VMUX_COMPOSITE,
1559 .vmux = SAA7115_COMPOSITE0,
1560 .amux = EM28XX_AMUX_LINE_IN,
1561 .gpio = vc211a_enable,
1562 }, {
1563 .type = EM28XX_VMUX_SVIDEO,
1564 .vmux = SAA7115_SVIDEO3,
1565 .amux = EM28XX_AMUX_LINE_IN,
1566 .gpio = vc211a_enable,
1567 } },
1568 },
1569 [EM2800_BOARD_LEADTEK_WINFAST_USBII] = {
1570 .name = "Leadtek Winfast USB II",
1571 .is_em2800 = 1,
1572 .tuner_type = TUNER_LG_PAL_NEW_TAPC,
1573 .tda9887_conf = TDA9887_PRESENT,
1574 .decoder = EM28XX_SAA711X,
1575 .input = { {
1576 .type = EM28XX_VMUX_TELEVISION,
1577 .vmux = SAA7115_COMPOSITE2,
1578 .amux = EM28XX_AMUX_VIDEO,
1579 }, {
1580 .type = EM28XX_VMUX_COMPOSITE,
1581 .vmux = SAA7115_COMPOSITE0,
1582 .amux = EM28XX_AMUX_LINE_IN,
1583 }, {
1584 .type = EM28XX_VMUX_SVIDEO,
1585 .vmux = SAA7115_SVIDEO3,
1586 .amux = EM28XX_AMUX_LINE_IN,
1587 } },
1588 },
1589 [EM2800_BOARD_KWORLD_USB2800] = {
1590 .name = "Kworld USB2800",
1591 .is_em2800 = 1,
1592 .tuner_type = TUNER_PHILIPS_FCV1236D,
1593 .tda9887_conf = TDA9887_PRESENT,
1594 .decoder = EM28XX_SAA711X,
1595 .input = { {
1596 .type = EM28XX_VMUX_TELEVISION,
1597 .vmux = SAA7115_COMPOSITE2,
1598 .amux = EM28XX_AMUX_VIDEO,
1599 }, {
1600 .type = EM28XX_VMUX_COMPOSITE,
1601 .vmux = SAA7115_COMPOSITE0,
1602 .amux = EM28XX_AMUX_LINE_IN,
1603 }, {
1604 .type = EM28XX_VMUX_SVIDEO,
1605 .vmux = SAA7115_SVIDEO3,
1606 .amux = EM28XX_AMUX_LINE_IN,
1607 } },
1608 },
1609 [EM2820_BOARD_PINNACLE_DVC_90] = {
1610 .name = "Pinnacle Dazzle DVC 90/100/101/107 / Kaiser Baas Video to DVD maker / Kworld DVD Maker 2 / Plextor ConvertX PX-AV100U",
1611 .tuner_type = TUNER_ABSENT,
1612 .decoder = EM28XX_SAA711X,
1613 .input = { {
1614 .type = EM28XX_VMUX_COMPOSITE,
1615 .vmux = SAA7115_COMPOSITE0,
1616 .amux = EM28XX_AMUX_LINE_IN,
1617 }, {
1618 .type = EM28XX_VMUX_SVIDEO,
1619 .vmux = SAA7115_SVIDEO3,
1620 .amux = EM28XX_AMUX_LINE_IN,
1621 } },
1622 },
1623 [EM2800_BOARD_VGEAR_POCKETTV] = {
1624 .name = "V-Gear PocketTV",
1625 .is_em2800 = 1,
1626 .tuner_type = TUNER_LG_PAL_NEW_TAPC,
1627 .tda9887_conf = TDA9887_PRESENT,
1628 .decoder = EM28XX_SAA711X,
1629 .input = { {
1630 .type = EM28XX_VMUX_TELEVISION,
1631 .vmux = SAA7115_COMPOSITE2,
1632 .amux = EM28XX_AMUX_VIDEO,
1633 }, {
1634 .type = EM28XX_VMUX_COMPOSITE,
1635 .vmux = SAA7115_COMPOSITE0,
1636 .amux = EM28XX_AMUX_LINE_IN,
1637 }, {
1638 .type = EM28XX_VMUX_SVIDEO,
1639 .vmux = SAA7115_SVIDEO3,
1640 .amux = EM28XX_AMUX_LINE_IN,
1641 } },
1642 },
1643 [EM2820_BOARD_PROLINK_PLAYTV_BOX4_USB2] = {
1644 .name = "Pixelview PlayTV Box 4 USB 2.0",
1645 .tda9887_conf = TDA9887_PRESENT,
1646 .tuner_type = TUNER_YMEC_TVF_5533MF,
1647 .decoder = EM28XX_SAA711X,
1648 .input = { {
1649 .type = EM28XX_VMUX_TELEVISION,
1650 .vmux = SAA7115_COMPOSITE2,
1651 .amux = EM28XX_AMUX_VIDEO,
1652 .aout = EM28XX_AOUT_MONO |
1653 EM28XX_AOUT_MASTER,
1654 }, {
1655 .type = EM28XX_VMUX_COMPOSITE,
1656 .vmux = SAA7115_COMPOSITE0,
1657 .amux = EM28XX_AMUX_LINE_IN,
1658 }, {
1659 .type = EM28XX_VMUX_SVIDEO,
1660 .vmux = SAA7115_SVIDEO3,
1661 .amux = EM28XX_AMUX_LINE_IN,
1662 } },
1663 },
1664 [EM2820_BOARD_PROLINK_PLAYTV_USB2] = {
1665 .name = "SIIG AVTuner-PVR / Pixelview Prolink PlayTV USB 2.0",
1666 .buttons = std_snapshot_button,
1667 .tda9887_conf = TDA9887_PRESENT,
1668 .tuner_type = TUNER_YMEC_TVF_5533MF,
1669 .tuner_addr = 0x60,
1670 .decoder = EM28XX_SAA711X,
1671 .input = { {
1672 .type = EM28XX_VMUX_TELEVISION,
1673 .vmux = SAA7115_COMPOSITE2,
1674 .amux = EM28XX_AMUX_VIDEO,
1675 .aout = EM28XX_AOUT_MONO |
1676 EM28XX_AOUT_MASTER,
1677 }, {
1678 .type = EM28XX_VMUX_COMPOSITE,
1679 .vmux = SAA7115_COMPOSITE0,
1680 .amux = EM28XX_AMUX_LINE_IN,
1681 }, {
1682 .type = EM28XX_VMUX_SVIDEO,
1683 .vmux = SAA7115_SVIDEO3,
1684 .amux = EM28XX_AMUX_LINE_IN,
1685 } },
1686 },
1687 [EM2860_BOARD_SAA711X_REFERENCE_DESIGN] = {
1688 .name = "EM2860/SAA711X Reference Design",
1689 .buttons = std_snapshot_button,
1690 .tuner_type = TUNER_ABSENT,
1691 .decoder = EM28XX_SAA711X,
1692 .input = { {
1693 .type = EM28XX_VMUX_SVIDEO,
1694 .vmux = SAA7115_SVIDEO3,
1695 }, {
1696 .type = EM28XX_VMUX_COMPOSITE,
1697 .vmux = SAA7115_COMPOSITE0,
1698 } },
1699 },
1700
1701 [EM2874_BOARD_LEADERSHIP_ISDBT] = {
1702 .def_i2c_bus = 1,
1703 .i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
1704 EM28XX_I2C_FREQ_100_KHZ,
1705 .xclk = EM28XX_XCLK_FREQUENCY_10MHZ,
1706 .name = "EM2874 Leadership ISDBT",
1707 .tuner_type = TUNER_ABSENT,
1708 .tuner_gpio = leadership_reset,
1709 .dvb_gpio = leadership_digital,
1710 .has_dvb = 1,
1711 },
1712
1713 [EM2880_BOARD_MSI_DIGIVOX_AD] = {
1714 .name = "MSI DigiVox A/D",
1715 .valid = EM28XX_BOARD_NOT_VALIDATED,
1716 .tuner_type = TUNER_XC2028,
1717 .tuner_gpio = default_tuner_gpio,
1718 .decoder = EM28XX_TVP5150,
1719 .input = { {
1720 .type = EM28XX_VMUX_TELEVISION,
1721 .vmux = TVP5150_COMPOSITE0,
1722 .amux = EM28XX_AMUX_VIDEO,
1723 .gpio = em2880_msi_digivox_ad_analog,
1724 }, {
1725 .type = EM28XX_VMUX_COMPOSITE,
1726 .vmux = TVP5150_COMPOSITE1,
1727 .amux = EM28XX_AMUX_LINE_IN,
1728 .gpio = em2880_msi_digivox_ad_analog,
1729 }, {
1730 .type = EM28XX_VMUX_SVIDEO,
1731 .vmux = TVP5150_SVIDEO,
1732 .amux = EM28XX_AMUX_LINE_IN,
1733 .gpio = em2880_msi_digivox_ad_analog,
1734 } },
1735 },
1736 [EM2880_BOARD_MSI_DIGIVOX_AD_II] = {
1737 .name = "MSI DigiVox A/D II",
1738 .valid = EM28XX_BOARD_NOT_VALIDATED,
1739 .tuner_type = TUNER_XC2028,
1740 .tuner_gpio = default_tuner_gpio,
1741 .decoder = EM28XX_TVP5150,
1742 .input = { {
1743 .type = EM28XX_VMUX_TELEVISION,
1744 .vmux = TVP5150_COMPOSITE0,
1745 .amux = EM28XX_AMUX_VIDEO,
1746 .gpio = em2880_msi_digivox_ad_analog,
1747 }, {
1748 .type = EM28XX_VMUX_COMPOSITE,
1749 .vmux = TVP5150_COMPOSITE1,
1750 .amux = EM28XX_AMUX_LINE_IN,
1751 .gpio = em2880_msi_digivox_ad_analog,
1752 }, {
1753 .type = EM28XX_VMUX_SVIDEO,
1754 .vmux = TVP5150_SVIDEO,
1755 .amux = EM28XX_AMUX_LINE_IN,
1756 .gpio = em2880_msi_digivox_ad_analog,
1757 } },
1758 },
1759 [EM2880_BOARD_KWORLD_DVB_305U] = {
1760 .name = "KWorld DVB-T 305U",
1761 .tuner_type = TUNER_XC2028,
1762 .tuner_gpio = default_tuner_gpio,
1763 .decoder = EM28XX_TVP5150,
1764 .input = { {
1765 .type = EM28XX_VMUX_TELEVISION,
1766 .vmux = TVP5150_COMPOSITE0,
1767 .amux = EM28XX_AMUX_VIDEO,
1768 }, {
1769 .type = EM28XX_VMUX_COMPOSITE,
1770 .vmux = TVP5150_COMPOSITE1,
1771 .amux = EM28XX_AMUX_LINE_IN,
1772 }, {
1773 .type = EM28XX_VMUX_SVIDEO,
1774 .vmux = TVP5150_SVIDEO,
1775 .amux = EM28XX_AMUX_LINE_IN,
1776 } },
1777 },
1778 [EM2880_BOARD_KWORLD_DVB_310U] = {
1779 .name = "KWorld DVB-T 310U",
1780 .tuner_type = TUNER_XC2028,
1781 .tuner_gpio = default_tuner_gpio,
1782 .has_dvb = 1,
1783 .dvb_gpio = default_digital,
1784 .mts_firmware = 1,
1785 .decoder = EM28XX_TVP5150,
1786 .input = { {
1787 .type = EM28XX_VMUX_TELEVISION,
1788 .vmux = TVP5150_COMPOSITE0,
1789 .amux = EM28XX_AMUX_VIDEO,
1790 .gpio = default_analog,
1791 }, {
1792 .type = EM28XX_VMUX_COMPOSITE,
1793 .vmux = TVP5150_COMPOSITE1,
1794 .amux = EM28XX_AMUX_LINE_IN,
1795 .gpio = default_analog,
1796 }, {
1797 .type = EM28XX_VMUX_SVIDEO,
1798 .vmux = TVP5150_SVIDEO,
1799 .amux = EM28XX_AMUX_LINE_IN,
1800 .gpio = default_analog,
1801 } },
1802 },
1803 [EM2882_BOARD_KWORLD_ATSC_315U] = {
1804 .name = "KWorld ATSC 315U HDTV TV Box",
1805 .valid = EM28XX_BOARD_NOT_VALIDATED,
1806 .tuner_type = TUNER_THOMSON_DTT761X,
1807 .tuner_gpio = em2882_kworld_315u_tuner_gpio,
1808 .tda9887_conf = TDA9887_PRESENT,
1809 .decoder = EM28XX_SAA711X,
1810 .has_dvb = 1,
1811 .dvb_gpio = em2882_kworld_315u_digital,
1812 .ir_codes = RC_MAP_KWORLD_315U,
1813 .xclk = EM28XX_XCLK_FREQUENCY_12MHZ,
1814 .i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE,
1815 #if 0
1816
1817 .input = { {
1818 .type = EM28XX_VMUX_TELEVISION,
1819 .vmux = SAA7115_COMPOSITE2,
1820 .amux = EM28XX_AMUX_VIDEO,
1821 .gpio = em2882_kworld_315u_analog,
1822 .aout = EM28XX_AOUT_PCM_IN | EM28XX_AOUT_PCM_STEREO,
1823 }, {
1824 .type = EM28XX_VMUX_COMPOSITE,
1825 .vmux = SAA7115_COMPOSITE0,
1826 .amux = EM28XX_AMUX_LINE_IN,
1827 .gpio = em2882_kworld_315u_analog1,
1828 .aout = EM28XX_AOUT_PCM_IN | EM28XX_AOUT_PCM_STEREO,
1829 }, {
1830 .type = EM28XX_VMUX_SVIDEO,
1831 .vmux = SAA7115_SVIDEO3,
1832 .amux = EM28XX_AMUX_LINE_IN,
1833 .gpio = em2882_kworld_315u_analog1,
1834 .aout = EM28XX_AOUT_PCM_IN | EM28XX_AOUT_PCM_STEREO,
1835 } },
1836 #endif
1837 },
1838 [EM2880_BOARD_EMPIRE_DUAL_TV] = {
1839 .name = "Empire dual TV",
1840 .tuner_type = TUNER_XC2028,
1841 .tuner_gpio = default_tuner_gpio,
1842 .has_dvb = 1,
1843 .dvb_gpio = default_digital,
1844 .mts_firmware = 1,
1845 .decoder = EM28XX_TVP5150,
1846 .input = { {
1847 .type = EM28XX_VMUX_TELEVISION,
1848 .vmux = TVP5150_COMPOSITE0,
1849 .amux = EM28XX_AMUX_VIDEO,
1850 .gpio = default_analog,
1851 }, {
1852 .type = EM28XX_VMUX_COMPOSITE,
1853 .vmux = TVP5150_COMPOSITE1,
1854 .amux = EM28XX_AMUX_LINE_IN,
1855 .gpio = default_analog,
1856 }, {
1857 .type = EM28XX_VMUX_SVIDEO,
1858 .vmux = TVP5150_SVIDEO,
1859 .amux = EM28XX_AMUX_LINE_IN,
1860 .gpio = default_analog,
1861 } },
1862 },
1863 [EM2881_BOARD_DNT_DA2_HYBRID] = {
1864 .name = "DNT DA2 Hybrid",
1865 .valid = EM28XX_BOARD_NOT_VALIDATED,
1866 .tuner_type = TUNER_XC2028,
1867 .tuner_gpio = default_tuner_gpio,
1868 .decoder = EM28XX_TVP5150,
1869 .input = { {
1870 .type = EM28XX_VMUX_TELEVISION,
1871 .vmux = TVP5150_COMPOSITE0,
1872 .amux = EM28XX_AMUX_VIDEO,
1873 .gpio = default_analog,
1874 }, {
1875 .type = EM28XX_VMUX_COMPOSITE,
1876 .vmux = TVP5150_COMPOSITE1,
1877 .amux = EM28XX_AMUX_LINE_IN,
1878 .gpio = default_analog,
1879 }, {
1880 .type = EM28XX_VMUX_SVIDEO,
1881 .vmux = TVP5150_SVIDEO,
1882 .amux = EM28XX_AMUX_LINE_IN,
1883 .gpio = default_analog,
1884 } },
1885 },
1886 [EM2881_BOARD_PINNACLE_HYBRID_PRO] = {
1887 .name = "Pinnacle Hybrid Pro",
1888 .tuner_type = TUNER_XC2028,
1889 .tuner_gpio = default_tuner_gpio,
1890 .decoder = EM28XX_TVP5150,
1891 .has_dvb = 1,
1892 .dvb_gpio = pinnacle_hybrid_pro_digital,
1893 .input = { {
1894 .type = EM28XX_VMUX_TELEVISION,
1895 .vmux = TVP5150_COMPOSITE0,
1896 .amux = EM28XX_AMUX_VIDEO,
1897 .gpio = pinnacle_hybrid_pro_analog,
1898 }, {
1899 .type = EM28XX_VMUX_COMPOSITE,
1900 .vmux = TVP5150_COMPOSITE1,
1901 .amux = EM28XX_AMUX_LINE_IN,
1902 .gpio = pinnacle_hybrid_pro_analog,
1903 }, {
1904 .type = EM28XX_VMUX_SVIDEO,
1905 .vmux = TVP5150_SVIDEO,
1906 .amux = EM28XX_AMUX_LINE_IN,
1907 .gpio = pinnacle_hybrid_pro_analog,
1908 } },
1909 },
1910 [EM2882_BOARD_PINNACLE_HYBRID_PRO_330E] = {
1911 .name = "Pinnacle Hybrid Pro (330e)",
1912 .tuner_type = TUNER_XC2028,
1913 .tuner_gpio = default_tuner_gpio,
1914 .mts_firmware = 1,
1915 .has_dvb = 1,
1916 .dvb_gpio = hauppauge_wintv_hvr_900R2_digital,
1917 .ir_codes = RC_MAP_PINNACLE_PCTV_HD,
1918 .decoder = EM28XX_TVP5150,
1919 .input = { {
1920 .type = EM28XX_VMUX_TELEVISION,
1921 .vmux = TVP5150_COMPOSITE0,
1922 .amux = EM28XX_AMUX_VIDEO,
1923 .gpio = hauppauge_wintv_hvr_900_analog,
1924 }, {
1925 .type = EM28XX_VMUX_COMPOSITE,
1926 .vmux = TVP5150_COMPOSITE1,
1927 .amux = EM28XX_AMUX_LINE_IN,
1928 .gpio = hauppauge_wintv_hvr_900_analog,
1929 }, {
1930 .type = EM28XX_VMUX_SVIDEO,
1931 .vmux = TVP5150_SVIDEO,
1932 .amux = EM28XX_AMUX_LINE_IN,
1933 .gpio = hauppauge_wintv_hvr_900_analog,
1934 } },
1935 },
1936 [EM2882_BOARD_KWORLD_VS_DVBT] = {
1937 .name = "Kworld VS-DVB-T 323UR",
1938 .tuner_type = TUNER_XC2028,
1939 .tuner_gpio = default_tuner_gpio,
1940 .decoder = EM28XX_TVP5150,
1941 .mts_firmware = 1,
1942 .has_dvb = 1,
1943 .dvb_gpio = kworld_330u_digital,
1944 .xclk = EM28XX_XCLK_FREQUENCY_12MHZ,
1945 .ir_codes = RC_MAP_KWORLD_315U,
1946 .input = { {
1947 .type = EM28XX_VMUX_TELEVISION,
1948 .vmux = TVP5150_COMPOSITE0,
1949 .amux = EM28XX_AMUX_VIDEO,
1950 }, {
1951 .type = EM28XX_VMUX_COMPOSITE,
1952 .vmux = TVP5150_COMPOSITE1,
1953 .amux = EM28XX_AMUX_LINE_IN,
1954 }, {
1955 .type = EM28XX_VMUX_SVIDEO,
1956 .vmux = TVP5150_SVIDEO,
1957 .amux = EM28XX_AMUX_LINE_IN,
1958 } },
1959 },
1960 [EM2882_BOARD_TERRATEC_HYBRID_XS] = {
1961 .name = "Terratec Cinergy Hybrid T USB XS (em2882)",
1962 .tuner_type = TUNER_XC2028,
1963 .tuner_gpio = default_tuner_gpio,
1964 .mts_firmware = 1,
1965 .decoder = EM28XX_TVP5150,
1966 .has_dvb = 1,
1967 .dvb_gpio = hauppauge_wintv_hvr_900_digital,
1968 .ir_codes = RC_MAP_TERRATEC_CINERGY_XS,
1969 .xclk = EM28XX_XCLK_FREQUENCY_12MHZ,
1970 .input = { {
1971 .type = EM28XX_VMUX_TELEVISION,
1972 .vmux = TVP5150_COMPOSITE0,
1973 .amux = EM28XX_AMUX_VIDEO,
1974 .gpio = hauppauge_wintv_hvr_900_analog,
1975 }, {
1976 .type = EM28XX_VMUX_COMPOSITE,
1977 .vmux = TVP5150_COMPOSITE1,
1978 .amux = EM28XX_AMUX_LINE_IN,
1979 .gpio = hauppauge_wintv_hvr_900_analog,
1980 }, {
1981 .type = EM28XX_VMUX_SVIDEO,
1982 .vmux = TVP5150_SVIDEO,
1983 .amux = EM28XX_AMUX_LINE_IN,
1984 .gpio = hauppauge_wintv_hvr_900_analog,
1985 } },
1986 },
1987 [EM2882_BOARD_DIKOM_DK300] = {
1988 .name = "Dikom DK300",
1989 .tuner_type = TUNER_XC2028,
1990 .tuner_gpio = default_tuner_gpio,
1991 .decoder = EM28XX_TVP5150,
1992 .mts_firmware = 1,
1993 .has_dvb = 1,
1994 .dvb_gpio = dikom_dk300_digital,
1995 .input = { {
1996 .type = EM28XX_VMUX_TELEVISION,
1997 .vmux = TVP5150_COMPOSITE0,
1998 .amux = EM28XX_AMUX_VIDEO,
1999 .gpio = default_analog,
2000 } },
2001 },
2002 [EM2883_BOARD_KWORLD_HYBRID_330U] = {
2003 .name = "Kworld PlusTV HD Hybrid 330",
2004 .tuner_type = TUNER_XC2028,
2005 .tuner_gpio = default_tuner_gpio,
2006 .decoder = EM28XX_TVP5150,
2007 .mts_firmware = 1,
2008 .has_dvb = 1,
2009 .dvb_gpio = kworld_330u_digital,
2010 .xclk = EM28XX_XCLK_FREQUENCY_12MHZ,
2011 .i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
2012 EM28XX_I2C_EEPROM_ON_BOARD |
2013 EM28XX_I2C_EEPROM_KEY_VALID,
2014 .input = { {
2015 .type = EM28XX_VMUX_TELEVISION,
2016 .vmux = TVP5150_COMPOSITE0,
2017 .amux = EM28XX_AMUX_VIDEO,
2018 .gpio = kworld_330u_analog,
2019 .aout = EM28XX_AOUT_PCM_IN | EM28XX_AOUT_PCM_STEREO,
2020 }, {
2021 .type = EM28XX_VMUX_COMPOSITE,
2022 .vmux = TVP5150_COMPOSITE1,
2023 .amux = EM28XX_AMUX_LINE_IN,
2024 .gpio = kworld_330u_analog,
2025 .aout = EM28XX_AOUT_PCM_IN | EM28XX_AOUT_PCM_STEREO,
2026 }, {
2027 .type = EM28XX_VMUX_SVIDEO,
2028 .vmux = TVP5150_SVIDEO,
2029 .amux = EM28XX_AMUX_LINE_IN,
2030 .gpio = kworld_330u_analog,
2031 } },
2032 },
2033 [EM2820_BOARD_COMPRO_VIDEOMATE_FORYOU] = {
2034 .name = "Compro VideoMate ForYou/Stereo",
2035 .tuner_type = TUNER_LG_PAL_NEW_TAPC,
2036 .tvaudio_addr = 0xb0,
2037 .tda9887_conf = TDA9887_PRESENT,
2038 .decoder = EM28XX_TVP5150,
2039 .adecoder = EM28XX_TVAUDIO,
2040 .mute_gpio = compro_mute_gpio,
2041 .input = { {
2042 .type = EM28XX_VMUX_TELEVISION,
2043 .vmux = TVP5150_COMPOSITE0,
2044 .amux = EM28XX_AMUX_VIDEO,
2045 .gpio = compro_unmute_tv_gpio,
2046 }, {
2047 .type = EM28XX_VMUX_SVIDEO,
2048 .vmux = TVP5150_SVIDEO,
2049 .amux = EM28XX_AMUX_LINE_IN,
2050 .gpio = compro_unmute_svid_gpio,
2051 } },
2052 },
2053 [EM2860_BOARD_KAIOMY_TVNPC_U2] = {
2054 .name = "Kaiomy TVnPC U2",
2055 .vchannels = 3,
2056 .tuner_type = TUNER_XC2028,
2057 .tuner_addr = 0x61,
2058 .mts_firmware = 1,
2059 .decoder = EM28XX_TVP5150,
2060 .tuner_gpio = default_tuner_gpio,
2061 .ir_codes = RC_MAP_KAIOMY,
2062 .input = { {
2063 .type = EM28XX_VMUX_TELEVISION,
2064 .vmux = TVP5150_COMPOSITE0,
2065 .amux = EM28XX_AMUX_VIDEO,
2066
2067 }, {
2068 .type = EM28XX_VMUX_COMPOSITE,
2069 .vmux = TVP5150_COMPOSITE1,
2070 .amux = EM28XX_AMUX_LINE_IN,
2071 }, {
2072 .type = EM28XX_VMUX_SVIDEO,
2073 .vmux = TVP5150_SVIDEO,
2074 .amux = EM28XX_AMUX_LINE_IN,
2075 } },
2076 .radio = {
2077 .type = EM28XX_RADIO,
2078 .amux = EM28XX_AMUX_LINE_IN,
2079 }
2080 },
2081 [EM2860_BOARD_EASYCAP] = {
2082 .name = "Easy Cap Capture DC-60",
2083 .vchannels = 2,
2084 .tuner_type = TUNER_ABSENT,
2085 .decoder = EM28XX_SAA711X,
2086 .input = { {
2087 .type = EM28XX_VMUX_COMPOSITE,
2088 .vmux = SAA7115_COMPOSITE0,
2089 .amux = EM28XX_AMUX_LINE_IN,
2090 }, {
2091 .type = EM28XX_VMUX_SVIDEO,
2092 .vmux = SAA7115_SVIDEO3,
2093 .amux = EM28XX_AMUX_LINE_IN,
2094 } },
2095 },
2096 [EM2820_BOARD_IODATA_GVMVP_SZ] = {
2097 .name = "IO-DATA GV-MVP/SZ",
2098 .tuner_type = TUNER_PHILIPS_FM1236_MK3,
2099 .tuner_gpio = default_tuner_gpio,
2100 .tda9887_conf = TDA9887_PRESENT,
2101 .decoder = EM28XX_TVP5150,
2102 .input = { {
2103 .type = EM28XX_VMUX_TELEVISION,
2104 .vmux = TVP5150_COMPOSITE0,
2105 .amux = EM28XX_AMUX_VIDEO,
2106 }, {
2107 .type = EM28XX_VMUX_COMPOSITE,
2108 .vmux = TVP5150_COMPOSITE1,
2109 .amux = EM28XX_AMUX_VIDEO,
2110 }, {
2111 .type = EM28XX_VMUX_SVIDEO,
2112 .vmux = TVP5150_SVIDEO,
2113 .amux = EM28XX_AMUX_VIDEO,
2114 } },
2115 },
2116 [EM2860_BOARD_TERRATEC_GRABBY] = {
2117 .name = "Terratec Grabby",
2118 .vchannels = 2,
2119 .tuner_type = TUNER_ABSENT,
2120 .decoder = EM28XX_SAA711X,
2121 .xclk = EM28XX_XCLK_FREQUENCY_12MHZ,
2122 .input = { {
2123 .type = EM28XX_VMUX_COMPOSITE,
2124 .vmux = SAA7115_COMPOSITE0,
2125 .amux = EM28XX_AMUX_LINE_IN,
2126 }, {
2127 .type = EM28XX_VMUX_SVIDEO,
2128 .vmux = SAA7115_SVIDEO3,
2129 .amux = EM28XX_AMUX_LINE_IN,
2130 } },
2131 .buttons = std_snapshot_button,
2132 .leds = terratec_grabby_leds,
2133 },
2134 [EM2860_BOARD_TERRATEC_AV350] = {
2135 .name = "Terratec AV350",
2136 .vchannels = 2,
2137 .tuner_type = TUNER_ABSENT,
2138 .decoder = EM28XX_TVP5150,
2139 .xclk = EM28XX_XCLK_FREQUENCY_12MHZ,
2140 .mute_gpio = terratec_av350_mute_gpio,
2141 .input = { {
2142 .type = EM28XX_VMUX_COMPOSITE,
2143 .vmux = TVP5150_COMPOSITE1,
2144 .amux = EM28XX_AMUX_LINE_IN,
2145 .gpio = terratec_av350_unmute_gpio,
2146
2147 }, {
2148 .type = EM28XX_VMUX_SVIDEO,
2149 .vmux = TVP5150_SVIDEO,
2150 .amux = EM28XX_AMUX_LINE_IN,
2151 .gpio = terratec_av350_unmute_gpio,
2152 } },
2153 },
2154
2155 [EM2860_BOARD_ELGATO_VIDEO_CAPTURE] = {
2156 .name = "Elgato Video Capture",
2157 .decoder = EM28XX_SAA711X,
2158 .tuner_type = TUNER_ABSENT,
2159 .input = { {
2160 .type = EM28XX_VMUX_COMPOSITE,
2161 .vmux = SAA7115_COMPOSITE0,
2162 .amux = EM28XX_AMUX_LINE_IN,
2163 }, {
2164 .type = EM28XX_VMUX_SVIDEO,
2165 .vmux = SAA7115_SVIDEO3,
2166 .amux = EM28XX_AMUX_LINE_IN,
2167 } },
2168 },
2169
2170 [EM2882_BOARD_EVGA_INDTUBE] = {
2171 .name = "Evga inDtube",
2172 .tuner_type = TUNER_XC2028,
2173 .tuner_gpio = default_tuner_gpio,
2174 .decoder = EM28XX_TVP5150,
2175 .xclk = EM28XX_XCLK_FREQUENCY_12MHZ,
2176 .mts_firmware = 1,
2177 .has_dvb = 1,
2178 .dvb_gpio = evga_indtube_digital,
2179 .ir_codes = RC_MAP_EVGA_INDTUBE,
2180 .input = { {
2181 .type = EM28XX_VMUX_TELEVISION,
2182 .vmux = TVP5150_COMPOSITE0,
2183 .amux = EM28XX_AMUX_VIDEO,
2184 .gpio = evga_indtube_analog,
2185 }, {
2186 .type = EM28XX_VMUX_COMPOSITE,
2187 .vmux = TVP5150_COMPOSITE1,
2188 .amux = EM28XX_AMUX_LINE_IN,
2189 .gpio = evga_indtube_analog,
2190 }, {
2191 .type = EM28XX_VMUX_SVIDEO,
2192 .vmux = TVP5150_SVIDEO,
2193 .amux = EM28XX_AMUX_LINE_IN,
2194 .gpio = evga_indtube_analog,
2195 } },
2196 },
2197
2198
2199
2200
2201 [EM2870_BOARD_REDDO_DVB_C_USB_BOX] = {
2202 .name = "Reddo DVB-C USB TV Box",
2203 .tuner_type = TUNER_ABSENT,
2204 .tuner_gpio = reddo_dvb_c_usb_box,
2205 .has_dvb = 1,
2206 },
2207
2208
2209
2210
2211
2212 [EM2870_BOARD_KWORLD_A340] = {
2213 .name = "KWorld PlusTV 340U or UB435-Q (ATSC)",
2214 .tuner_type = TUNER_ABSENT,
2215 .has_dvb = 1,
2216 .dvb_gpio = kworld_a340_digital,
2217 .tuner_gpio = default_tuner_gpio,
2218 },
2219
2220
2221
2222
2223 [EM28174_BOARD_PCTV_290E] = {
2224 .name = "PCTV nanoStick T2 290e",
2225 .def_i2c_bus = 1,
2226 .i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
2227 EM28XX_I2C_FREQ_100_KHZ,
2228 .tuner_type = TUNER_ABSENT,
2229 .tuner_gpio = pctv_290e,
2230 .has_dvb = 1,
2231 .ir_codes = RC_MAP_PINNACLE_PCTV_HD,
2232 },
2233
2234
2235
2236
2237 [EM28174_BOARD_PCTV_460E] = {
2238 .def_i2c_bus = 1,
2239 .i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
2240 EM28XX_I2C_FREQ_400_KHZ,
2241 .name = "PCTV DVB-S2 Stick (460e)",
2242 .tuner_type = TUNER_ABSENT,
2243 .tuner_gpio = pctv_460e,
2244 .has_dvb = 1,
2245 .ir_codes = RC_MAP_PINNACLE_PCTV_HD,
2246 },
2247
2248
2249
2250
2251 [EM2860_BOARD_HT_VIDBOX_NW03] = {
2252 .name = "Honestech Vidbox NW03",
2253 .tuner_type = TUNER_ABSENT,
2254 .decoder = EM28XX_SAA711X,
2255 .input = { {
2256 .type = EM28XX_VMUX_COMPOSITE,
2257 .vmux = SAA7115_COMPOSITE0,
2258 .amux = EM28XX_AMUX_LINE_IN,
2259 }, {
2260 .type = EM28XX_VMUX_SVIDEO,
2261 .vmux = SAA7115_SVIDEO3,
2262 .amux = EM28XX_AMUX_LINE_IN,
2263 } },
2264 },
2265
2266
2267
2268
2269 [EM2874_BOARD_MAXMEDIA_UB425_TC] = {
2270 .name = "MaxMedia UB425-TC",
2271 .tuner_type = TUNER_ABSENT,
2272 .tuner_gpio = maxmedia_ub425_tc,
2273 .has_dvb = 1,
2274 .ir_codes = RC_MAP_REDDO,
2275 .def_i2c_bus = 1,
2276 .i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
2277 EM28XX_I2C_FREQ_400_KHZ,
2278 },
2279
2280
2281
2282
2283 [EM2884_BOARD_PCTV_510E] = {
2284 .name = "PCTV QuatroStick (510e)",
2285 .tuner_type = TUNER_ABSENT,
2286 .tuner_gpio = pctv_510e,
2287 .has_dvb = 1,
2288 .ir_codes = RC_MAP_PINNACLE_PCTV_HD,
2289 .def_i2c_bus = 1,
2290 .i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
2291 EM28XX_I2C_FREQ_400_KHZ,
2292 },
2293
2294
2295
2296
2297 [EM2884_BOARD_PCTV_520E] = {
2298 .name = "PCTV QuatroStick nano (520e)",
2299 .tuner_type = TUNER_ABSENT,
2300 .tuner_gpio = pctv_520e,
2301 .has_dvb = 1,
2302 .ir_codes = RC_MAP_PINNACLE_PCTV_HD,
2303 .def_i2c_bus = 1,
2304 .i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
2305 EM28XX_I2C_FREQ_400_KHZ,
2306 },
2307 [EM2884_BOARD_TERRATEC_HTC_USB_XS] = {
2308 .name = "Terratec Cinergy HTC USB XS",
2309 .has_dvb = 1,
2310 .ir_codes = RC_MAP_NEC_TERRATEC_CINERGY_XS,
2311 .tuner_type = TUNER_ABSENT,
2312 .def_i2c_bus = 1,
2313 .i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
2314 EM28XX_I2C_FREQ_400_KHZ,
2315 },
2316
2317
2318
2319
2320
2321 [EM2874_BOARD_DELOCK_61959] = {
2322 .name = "Delock 61959",
2323 .tuner_type = TUNER_ABSENT,
2324 .tuner_gpio = maxmedia_ub425_tc,
2325 .has_dvb = 1,
2326 .ir_codes = RC_MAP_DELOCK_61959,
2327 .def_i2c_bus = 1,
2328 .i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
2329 EM28XX_I2C_FREQ_400_KHZ,
2330 },
2331
2332
2333
2334
2335 [EM2874_BOARD_KWORLD_UB435Q_V2] = {
2336 .name = "KWorld USB ATSC TV Stick UB435-Q V2",
2337 .tuner_type = TUNER_ABSENT,
2338 .has_dvb = 1,
2339 .dvb_gpio = kworld_a340_digital,
2340 .tuner_gpio = default_tuner_gpio,
2341 .def_i2c_bus = 1,
2342 },
2343
2344
2345
2346
2347 [EM2874_BOARD_KWORLD_UB435Q_V3] = {
2348 .name = "KWorld USB ATSC TV Stick UB435-Q V3",
2349 .tuner_type = TUNER_ABSENT,
2350 .has_dvb = 1,
2351 .tuner_gpio = kworld_ub435q_v3_digital,
2352 .def_i2c_bus = 1,
2353 .i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
2354 EM28XX_I2C_FREQ_100_KHZ,
2355 .leds = kworld_ub435q_v3_leds,
2356 },
2357 [EM2874_BOARD_PCTV_HD_MINI_80E] = {
2358 .name = "Pinnacle PCTV HD Mini",
2359 .tuner_type = TUNER_ABSENT,
2360 .has_dvb = 1,
2361 .dvb_gpio = em2874_pctv_80e_digital,
2362 .decoder = EM28XX_NODECODER,
2363 .ir_codes = RC_MAP_PINNACLE_PCTV_HD,
2364 .leds = pctv_80e_leds,
2365 },
2366
2367
2368
2369
2370 [EM2765_BOARD_SPEEDLINK_VAD_LAPLACE] = {
2371 .name = "SpeedLink Vicious And Devine Laplace webcam",
2372 .xclk = EM28XX_XCLK_FREQUENCY_24MHZ,
2373 .i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
2374 EM28XX_I2C_FREQ_100_KHZ,
2375 .def_i2c_bus = 1,
2376 .tuner_type = TUNER_ABSENT,
2377 .is_webcam = 1,
2378 .input = { {
2379 .type = EM28XX_VMUX_COMPOSITE,
2380 .amux = EM28XX_AMUX_VIDEO,
2381 .gpio = speedlink_vad_laplace_reg_seq,
2382 } },
2383 .buttons = speedlink_vad_laplace_buttons,
2384 .leds = speedlink_vad_laplace_leds,
2385 },
2386
2387
2388
2389
2390 [EM28178_BOARD_PCTV_461E] = {
2391 .def_i2c_bus = 1,
2392 .i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
2393 EM28XX_I2C_FREQ_400_KHZ,
2394 .name = "PCTV DVB-S2 Stick (461e)",
2395 .tuner_type = TUNER_ABSENT,
2396 .tuner_gpio = pctv_461e,
2397 .has_dvb = 1,
2398 .ir_codes = RC_MAP_PINNACLE_PCTV_HD,
2399 },
2400
2401
2402
2403
2404 [EM28178_BOARD_PCTV_292E] = {
2405 .name = "PCTV tripleStick (292e)",
2406 .def_i2c_bus = 1,
2407 .i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
2408 EM28XX_I2C_FREQ_400_KHZ,
2409 .tuner_type = TUNER_ABSENT,
2410 .tuner_gpio = pctv_292e,
2411 .has_dvb = 1,
2412 .ir_codes = RC_MAP_PINNACLE_PCTV_HD,
2413 },
2414 [EM2861_BOARD_LEADTEK_VC100] = {
2415 .name = "Leadtek VC100",
2416 .tuner_type = TUNER_ABSENT,
2417 .decoder = EM28XX_TVP5150,
2418 .input = { {
2419 .type = EM28XX_VMUX_COMPOSITE,
2420 .vmux = TVP5150_COMPOSITE1,
2421 .amux = EM28XX_AMUX_LINE_IN,
2422 }, {
2423 .type = EM28XX_VMUX_SVIDEO,
2424 .vmux = TVP5150_SVIDEO,
2425 .amux = EM28XX_AMUX_LINE_IN,
2426 } },
2427 },
2428
2429
2430
2431
2432 [EM28178_BOARD_TERRATEC_T2_STICK_HD] = {
2433 .name = "Terratec Cinergy T2 Stick HD",
2434 .def_i2c_bus = 1,
2435 .i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
2436 EM28XX_I2C_FREQ_400_KHZ,
2437 .tuner_type = TUNER_ABSENT,
2438 .tuner_gpio = terratec_t2_stick_hd,
2439 .has_dvb = 1,
2440 .ir_codes = RC_MAP_TERRATEC_SLIM_2,
2441 },
2442
2443
2444
2445
2446
2447 [EM28178_BOARD_PLEX_PX_BCUD] = {
2448 .name = "PLEX PX-BCUD",
2449 .xclk = EM28XX_XCLK_FREQUENCY_4_3MHZ,
2450 .def_i2c_bus = 1,
2451 .i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE,
2452 .tuner_type = TUNER_ABSENT,
2453 .tuner_gpio = plex_px_bcud,
2454 .has_dvb = 1,
2455 },
2456
2457
2458
2459
2460
2461 [EM28174_BOARD_HAUPPAUGE_WINTV_DUALHD_DVB] = {
2462 .name = "Hauppauge WinTV-dualHD DVB",
2463 .def_i2c_bus = 1,
2464 .i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
2465 EM28XX_I2C_FREQ_400_KHZ,
2466 .tuner_type = TUNER_ABSENT,
2467 .tuner_gpio = hauppauge_dualhd_dvb,
2468 .has_dvb = 1,
2469 .has_dual_ts = 1,
2470 .ir_codes = RC_MAP_HAUPPAUGE,
2471 .leds = hauppauge_dualhd_leds,
2472 },
2473
2474
2475
2476
2477
2478 [EM28174_BOARD_HAUPPAUGE_WINTV_DUALHD_01595] = {
2479 .name = "Hauppauge WinTV-dualHD 01595 ATSC/QAM",
2480 .def_i2c_bus = 1,
2481 .i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
2482 EM28XX_I2C_FREQ_400_KHZ,
2483 .tuner_type = TUNER_ABSENT,
2484 .tuner_gpio = hauppauge_dualhd_dvb,
2485 .has_dvb = 1,
2486 .has_dual_ts = 1,
2487 .ir_codes = RC_MAP_HAUPPAUGE,
2488 .leds = hauppauge_dualhd_leds,
2489 },
2490 };
2491 EXPORT_SYMBOL_GPL(em28xx_boards);
2492
2493 static const unsigned int em28xx_bcount = ARRAY_SIZE(em28xx_boards);
2494
2495
2496 struct usb_device_id em28xx_id_table[] = {
2497 { USB_DEVICE(0xeb1a, 0x2750),
2498 .driver_info = EM2750_BOARD_UNKNOWN },
2499 { USB_DEVICE(0xeb1a, 0x2751),
2500 .driver_info = EM2750_BOARD_UNKNOWN },
2501 { USB_DEVICE(0xeb1a, 0x2800),
2502 .driver_info = EM2800_BOARD_UNKNOWN },
2503 { USB_DEVICE(0xeb1a, 0x2710),
2504 .driver_info = EM2820_BOARD_UNKNOWN },
2505 { USB_DEVICE(0xeb1a, 0x2820),
2506 .driver_info = EM2820_BOARD_UNKNOWN },
2507 { USB_DEVICE(0xeb1a, 0x2821),
2508 .driver_info = EM2820_BOARD_UNKNOWN },
2509 { USB_DEVICE(0xeb1a, 0x2860),
2510 .driver_info = EM2820_BOARD_UNKNOWN },
2511 { USB_DEVICE(0xeb1a, 0x2861),
2512 .driver_info = EM2820_BOARD_UNKNOWN },
2513 { USB_DEVICE(0xeb1a, 0x2862),
2514 .driver_info = EM2820_BOARD_UNKNOWN },
2515 { USB_DEVICE(0xeb1a, 0x2863),
2516 .driver_info = EM2820_BOARD_UNKNOWN },
2517 { USB_DEVICE(0xeb1a, 0x2870),
2518 .driver_info = EM2820_BOARD_UNKNOWN },
2519 { USB_DEVICE(0xeb1a, 0x2881),
2520 .driver_info = EM2820_BOARD_UNKNOWN },
2521 { USB_DEVICE(0xeb1a, 0x2883),
2522 .driver_info = EM2820_BOARD_UNKNOWN },
2523 { USB_DEVICE(0xeb1a, 0x2868),
2524 .driver_info = EM2820_BOARD_UNKNOWN },
2525 { USB_DEVICE(0xeb1a, 0x2875),
2526 .driver_info = EM2820_BOARD_UNKNOWN },
2527 { USB_DEVICE(0xeb1a, 0x2885),
2528 .driver_info = EM2884_BOARD_TERRATEC_H5 },
2529 { USB_DEVICE(0xeb1a, 0xe300),
2530 .driver_info = EM2861_BOARD_KWORLD_PVRTV_300U },
2531 { USB_DEVICE(0xeb1a, 0xe303),
2532 .driver_info = EM2860_BOARD_KAIOMY_TVNPC_U2 },
2533 { USB_DEVICE(0xeb1a, 0xe305),
2534 .driver_info = EM2880_BOARD_KWORLD_DVB_305U },
2535 { USB_DEVICE(0xeb1a, 0xe310),
2536 .driver_info = EM2880_BOARD_MSI_DIGIVOX_AD },
2537 { USB_DEVICE(0xeb1a, 0xa313),
2538 .driver_info = EM2882_BOARD_KWORLD_ATSC_315U },
2539 { USB_DEVICE(0xeb1a, 0xa316),
2540 .driver_info = EM2883_BOARD_KWORLD_HYBRID_330U },
2541 { USB_DEVICE(0xeb1a, 0xe320),
2542 .driver_info = EM2880_BOARD_MSI_DIGIVOX_AD_II },
2543 { USB_DEVICE(0xeb1a, 0xe323),
2544 .driver_info = EM2882_BOARD_KWORLD_VS_DVBT },
2545 { USB_DEVICE(0xeb1a, 0xe350),
2546 .driver_info = EM2870_BOARD_KWORLD_350U },
2547 { USB_DEVICE(0xeb1a, 0xe355),
2548 .driver_info = EM2870_BOARD_KWORLD_355U },
2549 { USB_DEVICE(0xeb1a, 0x2801),
2550 .driver_info = EM2800_BOARD_GRABBEEX_USB2800 },
2551 { USB_DEVICE(0xeb1a, 0xe357),
2552 .driver_info = EM2870_BOARD_KWORLD_355U },
2553 { USB_DEVICE(0xeb1a, 0xe359),
2554 .driver_info = EM2870_BOARD_KWORLD_355U },
2555 { USB_DEVICE(0x1b80, 0xe302),
2556 .driver_info = EM2820_BOARD_PINNACLE_DVC_90 },
2557 { USB_DEVICE(0x1b80, 0xe304),
2558 .driver_info = EM2820_BOARD_PINNACLE_DVC_90 },
2559 { USB_DEVICE(0x0ccd, 0x0036),
2560 .driver_info = EM2820_BOARD_TERRATEC_CINERGY_250 },
2561 { USB_DEVICE(0x0ccd, 0x004c),
2562 .driver_info = EM2880_BOARD_TERRATEC_HYBRID_XS_FR },
2563 { USB_DEVICE(0x0ccd, 0x004f),
2564 .driver_info = EM2860_BOARD_TERRATEC_HYBRID_XS },
2565 { USB_DEVICE(0x0ccd, 0x005e),
2566 .driver_info = EM2882_BOARD_TERRATEC_HYBRID_XS },
2567 { USB_DEVICE(0x0ccd, 0x0042),
2568 .driver_info = EM2882_BOARD_TERRATEC_HYBRID_XS },
2569 { USB_DEVICE(0x0ccd, 0x0043),
2570 .driver_info = EM2870_BOARD_TERRATEC_XS_MT2060 },
2571 { USB_DEVICE(0x0ccd, 0x008e),
2572 .driver_info = EM2884_BOARD_TERRATEC_HTC_USB_XS },
2573 { USB_DEVICE(0x0ccd, 0x00ac),
2574 .driver_info = EM2884_BOARD_TERRATEC_HTC_USB_XS },
2575 { USB_DEVICE(0x0ccd, 0x10a2),
2576 .driver_info = EM2884_BOARD_TERRATEC_H5 },
2577 { USB_DEVICE(0x0ccd, 0x10ad),
2578 .driver_info = EM2884_BOARD_TERRATEC_H5 },
2579 { USB_DEVICE(0x0ccd, 0x10b6),
2580 .driver_info = EM2884_BOARD_TERRATEC_H5 },
2581 { USB_DEVICE(0x0ccd, 0x10b2),
2582 .driver_info = EM2884_BOARD_TERRATEC_H6 },
2583 { USB_DEVICE(0x0ccd, 0x0084),
2584 .driver_info = EM2860_BOARD_TERRATEC_AV350 },
2585 { USB_DEVICE(0x0ccd, 0x0096),
2586 .driver_info = EM2860_BOARD_TERRATEC_GRABBY },
2587 { USB_DEVICE(0x0ccd, 0x10AF),
2588 .driver_info = EM2860_BOARD_TERRATEC_GRABBY },
2589 { USB_DEVICE(0x0ccd, 0x00b2),
2590 .driver_info = EM2884_BOARD_CINERGY_HTC_STICK },
2591 { USB_DEVICE(0x0fd9, 0x0018),
2592 .driver_info = EM2884_BOARD_ELGATO_EYETV_HYBRID_2008 },
2593 { USB_DEVICE(0x0fd9, 0x0033),
2594 .driver_info = EM2860_BOARD_ELGATO_VIDEO_CAPTURE },
2595 { USB_DEVICE(0x185b, 0x2870),
2596 .driver_info = EM2870_BOARD_COMPRO_VIDEOMATE },
2597 { USB_DEVICE(0x185b, 0x2041),
2598 .driver_info = EM2820_BOARD_COMPRO_VIDEOMATE_FORYOU },
2599 { USB_DEVICE(0x2040, 0x4200),
2600 .driver_info = EM2820_BOARD_HAUPPAUGE_WINTV_USB_2 },
2601 { USB_DEVICE(0x2040, 0x4201),
2602 .driver_info = EM2820_BOARD_HAUPPAUGE_WINTV_USB_2 },
2603 { USB_DEVICE(0x2040, 0x6500),
2604 .driver_info = EM2880_BOARD_HAUPPAUGE_WINTV_HVR_900 },
2605 { USB_DEVICE(0x2040, 0x6502),
2606 .driver_info = EM2880_BOARD_HAUPPAUGE_WINTV_HVR_900_R2 },
2607 { USB_DEVICE(0x2040, 0x6513),
2608 .driver_info = EM2883_BOARD_HAUPPAUGE_WINTV_HVR_950 },
2609 { USB_DEVICE(0x2040, 0x6517),
2610 .driver_info = EM2883_BOARD_HAUPPAUGE_WINTV_HVR_950 },
2611 { USB_DEVICE(0x2040, 0x651b),
2612 .driver_info = EM2883_BOARD_HAUPPAUGE_WINTV_HVR_950 },
2613 { USB_DEVICE(0x2040, 0x651f),
2614 .driver_info = EM2883_BOARD_HAUPPAUGE_WINTV_HVR_850 },
2615 { USB_DEVICE(0x2040, 0x0265),
2616 .driver_info = EM28174_BOARD_HAUPPAUGE_WINTV_DUALHD_DVB },
2617 { USB_DEVICE(0x2040, 0x8265),
2618 .driver_info = EM28174_BOARD_HAUPPAUGE_WINTV_DUALHD_DVB },
2619 { USB_DEVICE(0x2040, 0x026d),
2620 .driver_info = EM28174_BOARD_HAUPPAUGE_WINTV_DUALHD_01595 },
2621 { USB_DEVICE(0x2040, 0x826d),
2622 .driver_info = EM28174_BOARD_HAUPPAUGE_WINTV_DUALHD_01595 },
2623 { USB_DEVICE(0x0438, 0xb002),
2624 .driver_info = EM2880_BOARD_AMD_ATI_TV_WONDER_HD_600 },
2625 { USB_DEVICE(0x2001, 0xf112),
2626 .driver_info = EM2820_BOARD_DLINK_USB_TV },
2627 { USB_DEVICE(0x2304, 0x0207),
2628 .driver_info = EM2820_BOARD_PINNACLE_DVC_90 },
2629 { USB_DEVICE(0x2304, 0x0208),
2630 .driver_info = EM2820_BOARD_PINNACLE_USB_2 },
2631 { USB_DEVICE(0x2304, 0x021a),
2632 .driver_info = EM2820_BOARD_PINNACLE_DVC_90 },
2633 { USB_DEVICE(0x2304, 0x0226),
2634 .driver_info = EM2882_BOARD_PINNACLE_HYBRID_PRO_330E },
2635 { USB_DEVICE(0x2304, 0x0227),
2636 .driver_info = EM2880_BOARD_PINNACLE_PCTV_HD_PRO },
2637 { USB_DEVICE(0x2304, 0x023f),
2638 .driver_info = EM2874_BOARD_PCTV_HD_MINI_80E },
2639 { USB_DEVICE(0x0413, 0x6023),
2640 .driver_info = EM2800_BOARD_LEADTEK_WINFAST_USBII },
2641 { USB_DEVICE(0x093b, 0xa003),
2642 .driver_info = EM2820_BOARD_PINNACLE_DVC_90 },
2643 { USB_DEVICE(0x093b, 0xa005),
2644 .driver_info = EM2861_BOARD_PLEXTOR_PX_TV100U },
2645 { USB_DEVICE(0x04bb, 0x0515),
2646 .driver_info = EM2820_BOARD_IODATA_GVMVP_SZ },
2647 { USB_DEVICE(0xeb1a, 0x50a6),
2648 .driver_info = EM2860_BOARD_GADMEI_UTV330 },
2649 { USB_DEVICE(0x1b80, 0xa340),
2650 .driver_info = EM2870_BOARD_KWORLD_A340 },
2651 { USB_DEVICE(0x1b80, 0xe346),
2652 .driver_info = EM2874_BOARD_KWORLD_UB435Q_V2 },
2653 { USB_DEVICE(0x1b80, 0xe34c),
2654 .driver_info = EM2874_BOARD_KWORLD_UB435Q_V3 },
2655 { USB_DEVICE(0x2013, 0x024f),
2656 .driver_info = EM28174_BOARD_PCTV_290E },
2657 { USB_DEVICE(0x2013, 0x024c),
2658 .driver_info = EM28174_BOARD_PCTV_460E },
2659 { USB_DEVICE(0x2040, 0x1605),
2660 .driver_info = EM2884_BOARD_HAUPPAUGE_WINTV_HVR_930C },
2661 { USB_DEVICE(0x1b80, 0xe755),
2662 .driver_info = EM2884_BOARD_C3TECH_DIGITAL_DUO },
2663 { USB_DEVICE(0xeb1a, 0x5006),
2664 .driver_info = EM2860_BOARD_HT_VIDBOX_NW03 },
2665 { USB_DEVICE(0x1b80, 0xe309),
2666 .driver_info = EM2860_BOARD_EASYCAP },
2667 { USB_DEVICE(0x1b80, 0xe425),
2668 .driver_info = EM2874_BOARD_MAXMEDIA_UB425_TC },
2669 { USB_DEVICE(0x2304, 0x0242),
2670 .driver_info = EM2884_BOARD_PCTV_510E },
2671 { USB_DEVICE(0x2013, 0x0251),
2672 .driver_info = EM2884_BOARD_PCTV_520E },
2673 { USB_DEVICE(0x1b80, 0xe1cc),
2674 .driver_info = EM2874_BOARD_DELOCK_61959 },
2675 { USB_DEVICE(0x1ae7, 0x9003),
2676 .driver_info = EM2765_BOARD_SPEEDLINK_VAD_LAPLACE },
2677 { USB_DEVICE(0x1ae7, 0x9004),
2678 .driver_info = EM2765_BOARD_SPEEDLINK_VAD_LAPLACE },
2679 { USB_DEVICE(0x2013, 0x0258),
2680 .driver_info = EM28178_BOARD_PCTV_461E },
2681 { USB_DEVICE(0x2013, 0x025f),
2682 .driver_info = EM28178_BOARD_PCTV_292E },
2683 { USB_DEVICE(0x2013, 0x0264),
2684 .driver_info = EM28178_BOARD_PCTV_292E },
2685 { USB_DEVICE(0x2040, 0x0264),
2686 .driver_info = EM28178_BOARD_PCTV_292E },
2687 { USB_DEVICE(0x2040, 0x8264),
2688 .driver_info = EM28178_BOARD_PCTV_292E },
2689 { USB_DEVICE(0x2040, 0x8268),
2690 .driver_info = EM28178_BOARD_PCTV_292E },
2691 { USB_DEVICE(0x0413, 0x6f07),
2692 .driver_info = EM2861_BOARD_LEADTEK_VC100 },
2693 { USB_DEVICE(0xeb1a, 0x8179),
2694 .driver_info = EM28178_BOARD_TERRATEC_T2_STICK_HD },
2695 { USB_DEVICE(0x3275, 0x0085),
2696 .driver_info = EM28178_BOARD_PLEX_PX_BCUD },
2697 { USB_DEVICE(0xeb1a, 0x5051),
2698 .driver_info = EM2860_BOARD_TVP5150_REFERENCE_DESIGN },
2699 { },
2700 };
2701 MODULE_DEVICE_TABLE(usb, em28xx_id_table);
2702
2703
2704
2705
2706 static const struct em28xx_hash_table em28xx_eeprom_hash[] = {
2707
2708 {0x6ce05a8f, EM2820_BOARD_PROLINK_PLAYTV_USB2, TUNER_YMEC_TVF_5533MF},
2709 {0x72cc5a8b, EM2820_BOARD_PROLINK_PLAYTV_BOX4_USB2, TUNER_YMEC_TVF_5533MF},
2710 {0x966a0441, EM2880_BOARD_KWORLD_DVB_310U, TUNER_XC2028},
2711 {0x166a0441, EM2880_BOARD_EMPIRE_DUAL_TV, TUNER_XC2028},
2712 {0xcee44a99, EM2882_BOARD_EVGA_INDTUBE, TUNER_XC2028},
2713 {0xb8846b20, EM2881_BOARD_PINNACLE_HYBRID_PRO, TUNER_XC2028},
2714 {0x63f653bd, EM2870_BOARD_REDDO_DVB_C_USB_BOX, TUNER_ABSENT},
2715 {0x4e913442, EM2882_BOARD_DIKOM_DK300, TUNER_XC2028},
2716 {0x85dd871e, EM2882_BOARD_ZOLID_HYBRID_TV_STICK, TUNER_XC2028},
2717 };
2718
2719
2720 static const struct em28xx_hash_table em28xx_i2c_hash[] = {
2721 {0xb06a32c3, EM2800_BOARD_TERRATEC_CINERGY_200, TUNER_LG_PAL_NEW_TAPC},
2722 {0xf51200e3, EM2800_BOARD_VGEAR_POCKETTV, TUNER_LG_PAL_NEW_TAPC},
2723 {0x1ba50080, EM2860_BOARD_SAA711X_REFERENCE_DESIGN, TUNER_ABSENT},
2724 {0x77800080, EM2860_BOARD_TVP5150_REFERENCE_DESIGN, TUNER_ABSENT},
2725 {0xc51200e3, EM2820_BOARD_GADMEI_TVR200, TUNER_LG_PAL_NEW_TAPC},
2726 {0x4ba50080, EM2861_BOARD_GADMEI_UTV330PLUS, TUNER_TNF_5335MF},
2727 {0x6b800080, EM2874_BOARD_LEADERSHIP_ISDBT, TUNER_ABSENT},
2728 {0x27e10080, EM2882_BOARD_ZOLID_HYBRID_TV_STICK, TUNER_XC2028},
2729 };
2730
2731
2732
2733 int em28xx_tuner_callback(void *ptr, int component, int command, int arg)
2734 {
2735 struct em28xx_i2c_bus *i2c_bus = ptr;
2736 struct em28xx *dev = i2c_bus->dev;
2737 int rc = 0;
2738
2739 if (dev->tuner_type != TUNER_XC2028 && dev->tuner_type != TUNER_XC5000)
2740 return 0;
2741
2742 if (command != XC2028_TUNER_RESET && command != XC5000_TUNER_RESET)
2743 return 0;
2744
2745 rc = em28xx_gpio_set(dev, dev->board.tuner_gpio);
2746
2747 return rc;
2748 }
2749 EXPORT_SYMBOL_GPL(em28xx_tuner_callback);
2750
2751 static inline void em28xx_set_xclk_i2c_speed(struct em28xx *dev)
2752 {
2753 const struct em28xx_board *board = &em28xx_boards[dev->model];
2754 u8 xclk = board->xclk, i2c_speed = board->i2c_speed;
2755
2756
2757
2758
2759
2760 if (!xclk)
2761 xclk = EM28XX_XCLK_IR_RC5_MODE |
2762 EM28XX_XCLK_FREQUENCY_12MHZ;
2763
2764 em28xx_write_reg(dev, EM28XX_R0F_XCLK, xclk);
2765
2766 if (!i2c_speed)
2767 i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE |
2768 EM28XX_I2C_FREQ_100_KHZ;
2769
2770 dev->i2c_speed = i2c_speed & 0x03;
2771
2772 if (!dev->board.is_em2800)
2773 em28xx_write_reg(dev, EM28XX_R06_I2C_CLK, i2c_speed);
2774 msleep(50);
2775 }
2776
2777 static inline void em28xx_set_model(struct em28xx *dev)
2778 {
2779 dev->board = em28xx_boards[dev->model];
2780 dev->has_msp34xx = dev->board.has_msp34xx;
2781 dev->is_webcam = dev->board.is_webcam;
2782
2783 em28xx_set_xclk_i2c_speed(dev);
2784
2785
2786 dev->def_i2c_bus = dev->board.def_i2c_bus;
2787 }
2788
2789
2790
2791
2792
2793
2794
2795 static int em28xx_wait_until_ac97_features_equals(struct em28xx *dev,
2796 int expected_feat)
2797 {
2798 unsigned long timeout = jiffies + msecs_to_jiffies(2000);
2799 int feat, powerdown;
2800
2801 while (time_is_after_jiffies(timeout)) {
2802 feat = em28xx_read_ac97(dev, AC97_RESET);
2803 if (feat < 0)
2804 return feat;
2805
2806 powerdown = em28xx_read_ac97(dev, AC97_POWERDOWN);
2807 if (powerdown < 0)
2808 return powerdown;
2809
2810 if (feat == expected_feat && feat != powerdown)
2811 return 0;
2812
2813 msleep(50);
2814 }
2815
2816 dev_warn(&dev->intf->dev, "AC97 registers access is not reliable !\n");
2817 return -ETIMEDOUT;
2818 }
2819
2820
2821
2822
2823
2824 static void em28xx_pre_card_setup(struct em28xx *dev)
2825 {
2826
2827
2828
2829
2830 em28xx_set_xclk_i2c_speed(dev);
2831
2832
2833 switch (dev->model) {
2834 case EM2861_BOARD_PLEXTOR_PX_TV100U:
2835
2836 dev->i2s_speed = 2048000;
2837 break;
2838 case EM2861_BOARD_KWORLD_PVRTV_300U:
2839 case EM2880_BOARD_KWORLD_DVB_305U:
2840 em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, 0x6d);
2841 usleep_range(10000, 11000);
2842 em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, 0x7d);
2843 usleep_range(10000, 11000);
2844 break;
2845 case EM2870_BOARD_COMPRO_VIDEOMATE:
2846
2847
2848
2849
2850 em28xx_write_reg(dev, EM2880_R04_GPO, 0x00);
2851 usleep_range(10000, 11000);
2852 em28xx_write_reg(dev, EM2880_R04_GPO, 0x01);
2853 usleep_range(10000, 11000);
2854 em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, 0xfd);
2855 msleep(70);
2856 em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, 0xfc);
2857 msleep(70);
2858 em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, 0xdc);
2859 msleep(70);
2860 em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, 0xfc);
2861 msleep(70);
2862 break;
2863 case EM2870_BOARD_TERRATEC_XS_MT2060:
2864
2865
2866
2867
2868 em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, 0xfe);
2869 msleep(70);
2870 em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, 0xde);
2871 msleep(70);
2872 em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, 0xfe);
2873 msleep(70);
2874 break;
2875 case EM2870_BOARD_PINNACLE_PCTV_DVB:
2876
2877
2878
2879
2880 em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, 0xfe);
2881 msleep(70);
2882 em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, 0xde);
2883 msleep(70);
2884 em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, 0xfe);
2885 msleep(70);
2886 break;
2887 case EM2820_BOARD_GADMEI_UTV310:
2888 case EM2820_BOARD_MSI_VOX_USB_2:
2889
2890 em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, 0xfd);
2891 break;
2892
2893 case EM2882_BOARD_KWORLD_ATSC_315U:
2894 em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, 0xff);
2895 usleep_range(10000, 11000);
2896 em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, 0xfe);
2897 usleep_range(10000, 11000);
2898 em28xx_write_reg(dev, EM2880_R04_GPO, 0x00);
2899 usleep_range(10000, 11000);
2900 em28xx_write_reg(dev, EM2880_R04_GPO, 0x08);
2901 usleep_range(10000, 11000);
2902 break;
2903
2904 case EM2860_BOARD_KAIOMY_TVNPC_U2:
2905 em28xx_write_regs(dev, EM28XX_R0F_XCLK, "\x07", 1);
2906 em28xx_write_regs(dev, EM28XX_R06_I2C_CLK, "\x40", 1);
2907 em28xx_write_regs(dev, 0x0d, "\x42", 1);
2908 em28xx_write_regs(dev, 0x08, "\xfd", 1);
2909 usleep_range(10000, 11000);
2910 em28xx_write_regs(dev, 0x08, "\xff", 1);
2911 usleep_range(10000, 11000);
2912 em28xx_write_regs(dev, 0x08, "\x7f", 1);
2913 usleep_range(10000, 11000);
2914 em28xx_write_regs(dev, 0x08, "\x6b", 1);
2915
2916 break;
2917 case EM2860_BOARD_EASYCAP:
2918 em28xx_write_regs(dev, 0x08, "\xf8", 1);
2919 break;
2920
2921 case EM2820_BOARD_IODATA_GVMVP_SZ:
2922 em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, 0xff);
2923 msleep(70);
2924 em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, 0xf7);
2925 usleep_range(10000, 11000);
2926 em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, 0xfe);
2927 msleep(70);
2928 em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, 0xfd);
2929 msleep(70);
2930 break;
2931
2932 case EM2860_BOARD_TERRATEC_GRABBY:
2933
2934
2935
2936
2937 em28xx_wait_until_ac97_features_equals(dev, 0x6a90);
2938 break;
2939 }
2940
2941 em28xx_gpio_set(dev, dev->board.tuner_gpio);
2942 em28xx_set_mode(dev, EM28XX_ANALOG_MODE);
2943
2944
2945 em28xx_set_mode(dev, EM28XX_SUSPEND);
2946 }
2947
2948 static int em28xx_hint_board(struct em28xx *dev)
2949 {
2950 int i;
2951
2952 if (dev->is_webcam) {
2953 if (dev->em28xx_sensor == EM28XX_MT9V011) {
2954 dev->model = EM2820_BOARD_SILVERCREST_WEBCAM;
2955 } else if (dev->em28xx_sensor == EM28XX_MT9M001 ||
2956 dev->em28xx_sensor == EM28XX_MT9M111) {
2957 dev->model = EM2750_BOARD_UNKNOWN;
2958 }
2959
2960
2961 return 0;
2962 }
2963
2964
2965
2966
2967
2968
2969
2970
2971
2972
2973 for (i = 0; i < ARRAY_SIZE(em28xx_eeprom_hash); i++) {
2974 if (dev->hash == em28xx_eeprom_hash[i].hash) {
2975 dev->model = em28xx_eeprom_hash[i].model;
2976 dev->tuner_type = em28xx_eeprom_hash[i].tuner;
2977
2978 dev_err(&dev->intf->dev,
2979 "Your board has no unique USB ID.\n"
2980 "A hint were successfully done, based on eeprom hash.\n"
2981 "This method is not 100%% failproof.\n"
2982 "If the board were misdetected, please email this log to:\n"
2983 "\tV4L Mailing List <linux-media@vger.kernel.org>\n"
2984 "Board detected as %s\n",
2985 em28xx_boards[dev->model].name);
2986
2987 return 0;
2988 }
2989 }
2990
2991
2992
2993
2994
2995
2996
2997
2998
2999
3000
3001
3002 if (!dev->i2c_hash)
3003 em28xx_do_i2c_scan(dev, dev->def_i2c_bus);
3004
3005 for (i = 0; i < ARRAY_SIZE(em28xx_i2c_hash); i++) {
3006 if (dev->i2c_hash == em28xx_i2c_hash[i].hash) {
3007 dev->model = em28xx_i2c_hash[i].model;
3008 dev->tuner_type = em28xx_i2c_hash[i].tuner;
3009 dev_err(&dev->intf->dev,
3010 "Your board has no unique USB ID.\n"
3011 "A hint were successfully done, based on i2c devicelist hash.\n"
3012 "This method is not 100%% failproof.\n"
3013 "If the board were misdetected, please email this log to:\n"
3014 "\tV4L Mailing List <linux-media@vger.kernel.org>\n"
3015 "Board detected as %s\n",
3016 em28xx_boards[dev->model].name);
3017
3018 return 0;
3019 }
3020 }
3021
3022 dev_err(&dev->intf->dev,
3023 "Your board has no unique USB ID and thus need a hint to be detected.\n"
3024 "You may try to use card=<n> insmod option to workaround that.\n"
3025 "Please send an email with this log to:\n"
3026 "\tV4L Mailing List <linux-media@vger.kernel.org>\n"
3027 "Board eeprom hash is 0x%08lx\n"
3028 "Board i2c devicelist hash is 0x%08lx\n",
3029 dev->hash, dev->i2c_hash);
3030
3031 dev_err(&dev->intf->dev,
3032 "Here is a list of valid choices for the card=<n> insmod option:\n");
3033 for (i = 0; i < em28xx_bcount; i++) {
3034 dev_err(&dev->intf->dev,
3035 " card=%d -> %s\n", i, em28xx_boards[i].name);
3036 }
3037 return -1;
3038 }
3039
3040 static void em28xx_card_setup(struct em28xx *dev)
3041 {
3042 int i, j, idx;
3043 bool duplicate_entry;
3044
3045
3046
3047
3048
3049 if (dev->is_webcam) {
3050 em28xx_detect_sensor(dev);
3051 if (dev->em28xx_sensor == EM28XX_NOSENSOR)
3052
3053 dev->is_webcam = 0;
3054 }
3055
3056 switch (dev->model) {
3057 case EM2750_BOARD_UNKNOWN:
3058 case EM2820_BOARD_UNKNOWN:
3059 case EM2800_BOARD_UNKNOWN:
3060
3061
3062
3063
3064
3065
3066
3067
3068
3069
3070
3071
3072
3073 if (em28xx_hint_board(dev) < 0) {
3074 dev_err(&dev->intf->dev, "Board not discovered\n");
3075 } else {
3076 em28xx_set_model(dev);
3077 em28xx_pre_card_setup(dev);
3078 }
3079 break;
3080 default:
3081 em28xx_set_model(dev);
3082 }
3083
3084 dev_info(&dev->intf->dev, "Identified as %s (card=%d)\n",
3085 dev->board.name, dev->model);
3086
3087 dev->tuner_type = em28xx_boards[dev->model].tuner_type;
3088
3089
3090 switch (dev->model) {
3091 case EM2820_BOARD_HAUPPAUGE_WINTV_USB_2:
3092 case EM2880_BOARD_HAUPPAUGE_WINTV_HVR_900:
3093 case EM2880_BOARD_HAUPPAUGE_WINTV_HVR_900_R2:
3094 case EM2883_BOARD_HAUPPAUGE_WINTV_HVR_850:
3095 case EM2883_BOARD_HAUPPAUGE_WINTV_HVR_950:
3096 case EM2884_BOARD_HAUPPAUGE_WINTV_HVR_930C:
3097 case EM28174_BOARD_HAUPPAUGE_WINTV_DUALHD_DVB:
3098 case EM28174_BOARD_HAUPPAUGE_WINTV_DUALHD_01595:
3099 {
3100 struct tveeprom tv;
3101
3102 if (!dev->eedata)
3103 break;
3104 #if defined(CONFIG_MODULES) && defined(MODULE)
3105 request_module("tveeprom");
3106 #endif
3107
3108
3109 tveeprom_hauppauge_analog(&tv, dev->eedata);
3110
3111 dev->tuner_type = tv.tuner_type;
3112
3113 if (tv.audio_processor == TVEEPROM_AUDPROC_MSP) {
3114 dev->i2s_speed = 2048000;
3115 dev->has_msp34xx = 1;
3116 }
3117 break;
3118 }
3119 case EM2882_BOARD_KWORLD_ATSC_315U:
3120 em28xx_write_reg(dev, 0x0d, 0x42);
3121 usleep_range(10000, 11000);
3122 em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, 0xfd);
3123 usleep_range(10000, 11000);
3124 break;
3125 case EM2820_BOARD_KWORLD_PVRTV2800RF:
3126
3127 em28xx_write_reg(dev, EM2820_R08_GPIO_CTRL, 0xf9);
3128 break;
3129 case EM2820_BOARD_UNKNOWN:
3130 case EM2800_BOARD_UNKNOWN:
3131
3132
3133
3134
3135
3136
3137
3138
3139
3140
3141
3142
3143
3144 case EM2880_BOARD_MSI_DIGIVOX_AD:
3145 if (!em28xx_hint_board(dev))
3146 em28xx_set_model(dev);
3147
3148
3149
3150
3151
3152
3153
3154 em28xx_gpio_set(dev, dev->board.tuner_gpio);
3155 em28xx_set_mode(dev, EM28XX_ANALOG_MODE);
3156 break;
3157
3158
3159
3160
3161
3162
3163
3164
3165
3166
3167
3168
3169
3170
3171 case EM2882_BOARD_KWORLD_VS_DVBT:
3172 if (!em28xx_hint_board(dev))
3173 em28xx_set_model(dev);
3174
3175
3176
3177
3178
3179
3180
3181 em28xx_gpio_set(dev, dev->board.tuner_gpio);
3182 em28xx_set_mode(dev, EM28XX_ANALOG_MODE);
3183 break;
3184 }
3185
3186 if (dev->board.valid == EM28XX_BOARD_NOT_VALIDATED) {
3187 dev_err(&dev->intf->dev,
3188 "\n\n"
3189 "The support for this board weren't valid yet.\n"
3190 "Please send a report of having this working\n"
3191 "not to V4L mailing list (and/or to other addresses)\n\n");
3192 }
3193
3194
3195 kfree(dev->eedata);
3196 dev->eedata = NULL;
3197
3198
3199 if (tuner >= 0)
3200 dev->tuner_type = tuner;
3201
3202
3203
3204
3205
3206
3207 idx = 0;
3208 for (i = 0; i < MAX_EM28XX_INPUT; i++) {
3209 if (!INPUT(i)->type)
3210 continue;
3211
3212
3213 duplicate_entry = false;
3214 for (j = 0; j < idx; j++) {
3215 if (INPUT(i)->amux == dev->amux_map[j]) {
3216 duplicate_entry = true;
3217 break;
3218 }
3219 }
3220 if (duplicate_entry)
3221 continue;
3222
3223 dev->amux_map[idx++] = INPUT(i)->amux;
3224 }
3225 for (; idx < MAX_EM28XX_INPUT; idx++)
3226 dev->amux_map[idx] = EM28XX_AMUX_UNUSED;
3227 }
3228
3229 void em28xx_setup_xc3028(struct em28xx *dev, struct xc2028_ctrl *ctl)
3230 {
3231 memset(ctl, 0, sizeof(*ctl));
3232
3233 ctl->fname = XC2028_DEFAULT_FIRMWARE;
3234 ctl->max_len = 64;
3235 ctl->mts = em28xx_boards[dev->model].mts_firmware;
3236
3237 switch (dev->model) {
3238 case EM2880_BOARD_EMPIRE_DUAL_TV:
3239 case EM2880_BOARD_HAUPPAUGE_WINTV_HVR_900:
3240 case EM2882_BOARD_TERRATEC_HYBRID_XS:
3241 case EM2880_BOARD_TERRATEC_HYBRID_XS:
3242 case EM2880_BOARD_TERRATEC_HYBRID_XS_FR:
3243 case EM2881_BOARD_PINNACLE_HYBRID_PRO:
3244 case EM2882_BOARD_ZOLID_HYBRID_TV_STICK:
3245 ctl->demod = XC3028_FE_ZARLINK456;
3246 break;
3247 case EM2880_BOARD_HAUPPAUGE_WINTV_HVR_900_R2:
3248 case EM2882_BOARD_PINNACLE_HYBRID_PRO_330E:
3249 ctl->demod = XC3028_FE_DEFAULT;
3250 break;
3251 case EM2880_BOARD_AMD_ATI_TV_WONDER_HD_600:
3252 ctl->demod = XC3028_FE_DEFAULT;
3253 ctl->fname = XC3028L_DEFAULT_FIRMWARE;
3254 break;
3255 case EM2883_BOARD_HAUPPAUGE_WINTV_HVR_850:
3256 case EM2883_BOARD_HAUPPAUGE_WINTV_HVR_950:
3257 case EM2880_BOARD_PINNACLE_PCTV_HD_PRO:
3258
3259 ctl->demod = XC3028_FE_DEFAULT;
3260 break;
3261 case EM2883_BOARD_KWORLD_HYBRID_330U:
3262 case EM2882_BOARD_DIKOM_DK300:
3263 case EM2882_BOARD_KWORLD_VS_DVBT:
3264 ctl->demod = XC3028_FE_CHINA;
3265 ctl->fname = XC2028_DEFAULT_FIRMWARE;
3266 break;
3267 case EM2882_BOARD_EVGA_INDTUBE:
3268 ctl->demod = XC3028_FE_CHINA;
3269 ctl->fname = XC3028L_DEFAULT_FIRMWARE;
3270 break;
3271 default:
3272 ctl->demod = XC3028_FE_OREN538;
3273 }
3274 }
3275 EXPORT_SYMBOL_GPL(em28xx_setup_xc3028);
3276
3277 static void request_module_async(struct work_struct *work)
3278 {
3279 struct em28xx *dev = container_of(work,
3280 struct em28xx, request_module_wk);
3281
3282
3283
3284
3285
3286
3287
3288
3289
3290
3291
3292
3293 if (dev->is_audio_only) {
3294 #if defined(CONFIG_MODULES) && defined(MODULE)
3295 request_module("em28xx-alsa");
3296 #endif
3297 return;
3298 }
3299
3300 em28xx_init_extension(dev);
3301
3302 #if defined(CONFIG_MODULES) && defined(MODULE)
3303 if (dev->has_video)
3304 request_module("em28xx-v4l");
3305 if (dev->usb_audio_type == EM28XX_USB_AUDIO_CLASS)
3306 request_module("snd-usb-audio");
3307 else if (dev->usb_audio_type == EM28XX_USB_AUDIO_VENDOR)
3308 request_module("em28xx-alsa");
3309 if (dev->board.has_dvb)
3310 request_module("em28xx-dvb");
3311 if (dev->board.buttons ||
3312 ((dev->board.ir_codes || dev->board.has_ir_i2c) && !disable_ir))
3313 request_module("em28xx-rc");
3314 #endif
3315 }
3316
3317 static void request_modules(struct em28xx *dev)
3318 {
3319 INIT_WORK(&dev->request_module_wk, request_module_async);
3320 schedule_work(&dev->request_module_wk);
3321 }
3322
3323 static void flush_request_modules(struct em28xx *dev)
3324 {
3325 flush_work(&dev->request_module_wk);
3326 }
3327
3328 static int em28xx_media_device_init(struct em28xx *dev,
3329 struct usb_device *udev)
3330 {
3331 #ifdef CONFIG_MEDIA_CONTROLLER
3332 struct media_device *mdev;
3333
3334 mdev = kzalloc(sizeof(*mdev), GFP_KERNEL);
3335 if (!mdev)
3336 return -ENOMEM;
3337
3338 if (udev->product)
3339 media_device_usb_init(mdev, udev, udev->product);
3340 else if (udev->manufacturer)
3341 media_device_usb_init(mdev, udev, udev->manufacturer);
3342 else
3343 media_device_usb_init(mdev, udev, dev_name(&dev->intf->dev));
3344
3345 dev->media_dev = mdev;
3346 #endif
3347 return 0;
3348 }
3349
3350 static void em28xx_unregister_media_device(struct em28xx *dev)
3351 {
3352 #ifdef CONFIG_MEDIA_CONTROLLER
3353 if (dev->media_dev) {
3354 media_device_unregister(dev->media_dev);
3355 media_device_cleanup(dev->media_dev);
3356 kfree(dev->media_dev);
3357 dev->media_dev = NULL;
3358 }
3359 #endif
3360 }
3361
3362
3363
3364
3365
3366
3367 static void em28xx_release_resources(struct em28xx *dev)
3368 {
3369 struct usb_device *udev = interface_to_usbdev(dev->intf);
3370
3371
3372
3373 mutex_lock(&dev->lock);
3374
3375 em28xx_unregister_media_device(dev);
3376
3377 if (dev->def_i2c_bus)
3378 em28xx_i2c_unregister(dev, 1);
3379 em28xx_i2c_unregister(dev, 0);
3380
3381 if (dev->ts == PRIMARY_TS)
3382 usb_put_dev(udev);
3383
3384
3385 clear_bit(dev->devno, em28xx_devused);
3386
3387 mutex_unlock(&dev->lock);
3388 };
3389
3390
3391
3392
3393
3394
3395
3396
3397 void em28xx_free_device(struct kref *ref)
3398 {
3399 struct em28xx *dev = kref_to_dev(ref);
3400
3401 dev_info(&dev->intf->dev, "Freeing device\n");
3402
3403 if (!dev->disconnected)
3404 em28xx_release_resources(dev);
3405
3406 if (dev->ts == PRIMARY_TS)
3407 kfree(dev->alt_max_pkt_size_isoc);
3408
3409 kfree(dev);
3410 }
3411 EXPORT_SYMBOL_GPL(em28xx_free_device);
3412
3413
3414
3415
3416
3417 static int em28xx_init_dev(struct em28xx *dev, struct usb_device *udev,
3418 struct usb_interface *intf,
3419 int minor)
3420 {
3421 int retval;
3422 const char *chip_name = NULL;
3423
3424 dev->intf = intf;
3425 mutex_init(&dev->ctrl_urb_lock);
3426 spin_lock_init(&dev->slock);
3427
3428 dev->em28xx_write_regs = em28xx_write_regs;
3429 dev->em28xx_read_reg = em28xx_read_reg;
3430 dev->em28xx_read_reg_req_len = em28xx_read_reg_req_len;
3431 dev->em28xx_write_regs_req = em28xx_write_regs_req;
3432 dev->em28xx_read_reg_req = em28xx_read_reg_req;
3433 dev->board.is_em2800 = em28xx_boards[dev->model].is_em2800;
3434
3435 em28xx_set_model(dev);
3436
3437 dev->wait_after_write = 5;
3438
3439
3440 retval = em28xx_read_reg(dev, EM28XX_R0A_CHIPID);
3441 if (retval > 0) {
3442 dev->chip_id = retval;
3443
3444 switch (dev->chip_id) {
3445 case CHIP_ID_EM2800:
3446 chip_name = "em2800";
3447 break;
3448 case CHIP_ID_EM2710:
3449 chip_name = "em2710";
3450 break;
3451 case CHIP_ID_EM2750:
3452 chip_name = "em2750";
3453 break;
3454 case CHIP_ID_EM2765:
3455 chip_name = "em2765";
3456 dev->wait_after_write = 0;
3457 dev->is_em25xx = 1;
3458 dev->eeprom_addrwidth_16bit = 1;
3459 break;
3460 case CHIP_ID_EM2820:
3461 chip_name = "em2710/2820";
3462 if (le16_to_cpu(udev->descriptor.idVendor) == 0xeb1a) {
3463 __le16 idProd = udev->descriptor.idProduct;
3464
3465 if (le16_to_cpu(idProd) == 0x2710)
3466 chip_name = "em2710";
3467 else if (le16_to_cpu(idProd) == 0x2820)
3468 chip_name = "em2820";
3469 }
3470
3471 break;
3472 case CHIP_ID_EM2840:
3473 chip_name = "em2840";
3474 break;
3475 case CHIP_ID_EM2860:
3476 chip_name = "em2860";
3477 break;
3478 case CHIP_ID_EM2870:
3479 chip_name = "em2870";
3480 dev->wait_after_write = 0;
3481 break;
3482 case CHIP_ID_EM2874:
3483 chip_name = "em2874";
3484 dev->wait_after_write = 0;
3485 dev->eeprom_addrwidth_16bit = 1;
3486 break;
3487 case CHIP_ID_EM28174:
3488 chip_name = "em28174";
3489 dev->wait_after_write = 0;
3490 dev->eeprom_addrwidth_16bit = 1;
3491 break;
3492 case CHIP_ID_EM28178:
3493 chip_name = "em28178";
3494 dev->wait_after_write = 0;
3495 dev->eeprom_addrwidth_16bit = 1;
3496 break;
3497 case CHIP_ID_EM2883:
3498 chip_name = "em2882/3";
3499 dev->wait_after_write = 0;
3500 break;
3501 case CHIP_ID_EM2884:
3502 chip_name = "em2884";
3503 dev->wait_after_write = 0;
3504 dev->eeprom_addrwidth_16bit = 1;
3505 break;
3506 }
3507 }
3508 if (!chip_name)
3509 dev_info(&dev->intf->dev,
3510 "unknown em28xx chip ID (%d)\n", dev->chip_id);
3511 else
3512 dev_info(&dev->intf->dev, "chip ID is %s\n", chip_name);
3513
3514 em28xx_media_device_init(dev, udev);
3515
3516 if (dev->is_audio_only) {
3517 retval = em28xx_audio_setup(dev);
3518 if (retval)
3519 return -ENODEV;
3520 em28xx_init_extension(dev);
3521
3522 return 0;
3523 }
3524
3525 em28xx_pre_card_setup(dev);
3526
3527 rt_mutex_init(&dev->i2c_bus_lock);
3528
3529
3530 if (dev->board.is_em2800)
3531 retval = em28xx_i2c_register(dev, 0, EM28XX_I2C_ALGO_EM2800);
3532 else
3533 retval = em28xx_i2c_register(dev, 0, EM28XX_I2C_ALGO_EM28XX);
3534 if (retval < 0) {
3535 dev_err(&dev->intf->dev,
3536 "%s: em28xx_i2c_register bus 0 - error [%d]!\n",
3537 __func__, retval);
3538 return retval;
3539 }
3540
3541
3542 if (dev->def_i2c_bus) {
3543 if (dev->is_em25xx)
3544 retval = em28xx_i2c_register(dev, 1,
3545 EM28XX_I2C_ALGO_EM25XX_BUS_B);
3546 else
3547 retval = em28xx_i2c_register(dev, 1,
3548 EM28XX_I2C_ALGO_EM28XX);
3549 if (retval < 0) {
3550 dev_err(&dev->intf->dev,
3551 "%s: em28xx_i2c_register bus 1 - error [%d]!\n",
3552 __func__, retval);
3553
3554 em28xx_i2c_unregister(dev, 0);
3555
3556 return retval;
3557 }
3558 }
3559
3560
3561 em28xx_card_setup(dev);
3562
3563 return 0;
3564 }
3565
3566 static int em28xx_duplicate_dev(struct em28xx *dev)
3567 {
3568 int nr;
3569 struct em28xx *sec_dev = kmemdup(dev, sizeof(*sec_dev), GFP_KERNEL);
3570
3571 if (!sec_dev) {
3572 dev->dev_next = NULL;
3573 return -ENOMEM;
3574 }
3575
3576 do {
3577 nr = find_first_zero_bit(em28xx_devused, EM28XX_MAXBOARDS);
3578 if (nr >= EM28XX_MAXBOARDS) {
3579
3580 dev_warn(&dev->intf->dev, ": Supports only %i em28xx boards.\n",
3581 EM28XX_MAXBOARDS);
3582 kfree(sec_dev);
3583 dev->dev_next = NULL;
3584 return -ENOMEM;
3585 }
3586 } while (test_and_set_bit(nr, em28xx_devused));
3587 sec_dev->devno = nr;
3588 snprintf(sec_dev->name, 28, "em28xx #%d", nr);
3589 sec_dev->dev_next = NULL;
3590 dev->dev_next = sec_dev;
3591 return 0;
3592 }
3593
3594
3595 #define hb_mult(wMaxPacketSize) (1 + (((wMaxPacketSize) >> 11) & 0x03))
3596
3597 static void em28xx_check_usb_descriptor(struct em28xx *dev,
3598 struct usb_device *udev,
3599 struct usb_interface *intf,
3600 int alt, int ep,
3601 bool *has_vendor_audio,
3602 bool *has_video,
3603 bool *has_dvb)
3604 {
3605 const struct usb_endpoint_descriptor *e;
3606 int sizedescr, size;
3607
3608
3609
3610
3611
3612
3613
3614
3615
3616
3617
3618
3619
3620
3621
3622
3623
3624
3625
3626
3627
3628
3629
3630
3631
3632
3633 e = &intf->altsetting[alt].endpoint[ep].desc;
3634
3635 if (!usb_endpoint_dir_in(e))
3636 return;
3637
3638 sizedescr = le16_to_cpu(e->wMaxPacketSize);
3639 size = sizedescr & 0x7ff;
3640
3641 if (udev->speed == USB_SPEED_HIGH)
3642 size = size * hb_mult(sizedescr);
3643
3644
3645
3646 switch (e->bEndpointAddress) {
3647 case 0x82:
3648 *has_video = true;
3649 if (usb_endpoint_xfer_isoc(e)) {
3650 dev->analog_ep_isoc = e->bEndpointAddress;
3651 dev->alt_max_pkt_size_isoc[alt] = size;
3652 } else if (usb_endpoint_xfer_bulk(e)) {
3653 dev->analog_ep_bulk = e->bEndpointAddress;
3654 }
3655 return;
3656 case 0x83:
3657 if (usb_endpoint_xfer_isoc(e))
3658 *has_vendor_audio = true;
3659 else
3660 dev_err(&intf->dev,
3661 "error: skipping audio endpoint 0x83, because it uses bulk transfers !\n");
3662 return;
3663 case 0x84:
3664 if (*has_video && (usb_endpoint_xfer_bulk(e))) {
3665 dev->analog_ep_bulk = e->bEndpointAddress;
3666 } else {
3667 if (usb_endpoint_xfer_isoc(e)) {
3668 if (size > dev->dvb_max_pkt_size_isoc) {
3669
3670
3671
3672
3673
3674
3675
3676 *has_dvb = true;
3677 dev->dvb_ep_isoc = e->bEndpointAddress;
3678 dev->dvb_max_pkt_size_isoc = size;
3679 dev->dvb_alt_isoc = alt;
3680 }
3681 } else {
3682 *has_dvb = true;
3683 dev->dvb_ep_bulk = e->bEndpointAddress;
3684 }
3685 }
3686 return;
3687 case 0x85:
3688 if (usb_endpoint_xfer_isoc(e)) {
3689 if (size > dev->dvb_max_pkt_size_isoc_ts2) {
3690 dev->dvb_ep_isoc_ts2 = e->bEndpointAddress;
3691 dev->dvb_max_pkt_size_isoc_ts2 = size;
3692 dev->dvb_alt_isoc = alt;
3693 }
3694 } else {
3695 dev->dvb_ep_bulk_ts2 = e->bEndpointAddress;
3696 }
3697 return;
3698 }
3699 }
3700
3701
3702
3703
3704
3705 static int em28xx_usb_probe(struct usb_interface *intf,
3706 const struct usb_device_id *id)
3707 {
3708 struct usb_device *udev;
3709 struct em28xx *dev = NULL;
3710 int retval;
3711 bool has_vendor_audio = false, has_video = false, has_dvb = false;
3712 int i, nr, try_bulk;
3713 const int ifnum = intf->altsetting[0].desc.bInterfaceNumber;
3714 char *speed;
3715
3716 udev = usb_get_dev(interface_to_usbdev(intf));
3717
3718
3719 do {
3720 nr = find_first_zero_bit(em28xx_devused, EM28XX_MAXBOARDS);
3721 if (nr >= EM28XX_MAXBOARDS) {
3722
3723 dev_err(&intf->dev,
3724 "Driver supports up to %i em28xx boards.\n",
3725 EM28XX_MAXBOARDS);
3726 retval = -ENOMEM;
3727 goto err_no_slot;
3728 }
3729 } while (test_and_set_bit(nr, em28xx_devused));
3730
3731
3732 if (intf->altsetting[0].desc.bInterfaceClass == USB_CLASS_AUDIO) {
3733 dev_info(&intf->dev,
3734 "audio device (%04x:%04x): interface %i, class %i\n",
3735 le16_to_cpu(udev->descriptor.idVendor),
3736 le16_to_cpu(udev->descriptor.idProduct),
3737 ifnum,
3738 intf->altsetting[0].desc.bInterfaceClass);
3739
3740 retval = -ENODEV;
3741 goto err;
3742 }
3743
3744
3745 dev = kzalloc(sizeof(*dev), GFP_KERNEL);
3746 if (!dev) {
3747 retval = -ENOMEM;
3748 goto err;
3749 }
3750
3751
3752 dev->alt_max_pkt_size_isoc = kcalloc(intf->num_altsetting,
3753 sizeof(dev->alt_max_pkt_size_isoc[0]),
3754 GFP_KERNEL);
3755 if (!dev->alt_max_pkt_size_isoc) {
3756 kfree(dev);
3757 retval = -ENOMEM;
3758 goto err;
3759 }
3760
3761
3762 for (i = 0; i < intf->num_altsetting; i++) {
3763 int ep;
3764
3765 for (ep = 0;
3766 ep < intf->altsetting[i].desc.bNumEndpoints;
3767 ep++)
3768 em28xx_check_usb_descriptor(dev, udev, intf,
3769 i, ep,
3770 &has_vendor_audio,
3771 &has_video,
3772 &has_dvb);
3773 }
3774
3775 if (!(has_vendor_audio || has_video || has_dvb)) {
3776 retval = -ENODEV;
3777 goto err_free;
3778 }
3779
3780 switch (udev->speed) {
3781 case USB_SPEED_LOW:
3782 speed = "1.5";
3783 break;
3784 case USB_SPEED_UNKNOWN:
3785 case USB_SPEED_FULL:
3786 speed = "12";
3787 break;
3788 case USB_SPEED_HIGH:
3789 speed = "480";
3790 break;
3791 default:
3792 speed = "unknown";
3793 }
3794
3795 dev_info(&intf->dev,
3796 "New device %s %s @ %s Mbps (%04x:%04x, interface %d, class %d)\n",
3797 udev->manufacturer ? udev->manufacturer : "",
3798 udev->product ? udev->product : "",
3799 speed,
3800 le16_to_cpu(udev->descriptor.idVendor),
3801 le16_to_cpu(udev->descriptor.idProduct),
3802 ifnum,
3803 intf->altsetting->desc.bInterfaceNumber);
3804
3805
3806
3807
3808
3809
3810 if (udev->speed != USB_SPEED_HIGH && disable_usb_speed_check == 0) {
3811 dev_err(&intf->dev, "Device initialization failed.\n");
3812 dev_err(&intf->dev,
3813 "Device must be connected to a high-speed USB 2.0 port.\n");
3814 retval = -ENODEV;
3815 goto err_free;
3816 }
3817
3818 dev->devno = nr;
3819 dev->model = id->driver_info;
3820 dev->alt = -1;
3821 dev->is_audio_only = has_vendor_audio && !(has_video || has_dvb);
3822 dev->has_video = has_video;
3823 dev->ifnum = ifnum;
3824
3825 dev->ts = PRIMARY_TS;
3826 snprintf(dev->name, 28, "em28xx");
3827 dev->dev_next = NULL;
3828
3829 if (has_vendor_audio) {
3830 dev_info(&intf->dev,
3831 "Audio interface %i found (Vendor Class)\n", ifnum);
3832 dev->usb_audio_type = EM28XX_USB_AUDIO_VENDOR;
3833 }
3834
3835 for (i = 0; i < udev->config->desc.bNumInterfaces; i++) {
3836 struct usb_interface *uif = udev->config->interface[i];
3837
3838 if (uif->altsetting[0].desc.bInterfaceClass == USB_CLASS_AUDIO) {
3839 if (has_vendor_audio)
3840 dev_err(&intf->dev,
3841 "em28xx: device seems to have vendor AND usb audio class interfaces !\n"
3842 "\t\tThe vendor interface will be ignored. Please contact the developers <linux-media@vger.kernel.org>\n");
3843 dev->usb_audio_type = EM28XX_USB_AUDIO_CLASS;
3844 break;
3845 }
3846 }
3847
3848 if (has_video)
3849 dev_info(&intf->dev, "Video interface %i found:%s%s\n",
3850 ifnum,
3851 dev->analog_ep_bulk ? " bulk" : "",
3852 dev->analog_ep_isoc ? " isoc" : "");
3853 if (has_dvb)
3854 dev_info(&intf->dev, "DVB interface %i found:%s%s\n",
3855 ifnum,
3856 dev->dvb_ep_bulk ? " bulk" : "",
3857 dev->dvb_ep_isoc ? " isoc" : "");
3858
3859 dev->num_alt = intf->num_altsetting;
3860
3861 if ((unsigned int)card[nr] < em28xx_bcount)
3862 dev->model = card[nr];
3863
3864
3865 usb_set_intfdata(intf, dev);
3866
3867
3868 mutex_init(&dev->lock);
3869 retval = em28xx_init_dev(dev, udev, intf, nr);
3870 if (retval)
3871 goto err_free;
3872
3873 if (usb_xfer_mode < 0) {
3874 if (dev->is_webcam)
3875 try_bulk = 1;
3876 else
3877 try_bulk = 0;
3878 } else {
3879 try_bulk = usb_xfer_mode > 0;
3880 }
3881
3882
3883 if (has_video &&
3884 dev->board.decoder == EM28XX_NODECODER &&
3885 dev->em28xx_sensor == EM28XX_NOSENSOR) {
3886 dev_err(&intf->dev,
3887 "Currently, V4L2 is not supported on this model\n");
3888 has_video = false;
3889 dev->has_video = false;
3890 }
3891
3892 if (dev->board.has_dual_ts &&
3893 (dev->tuner_type != TUNER_ABSENT || INPUT(0)->type)) {
3894
3895
3896
3897
3898 dev_err(&intf->dev,
3899 "We currently don't support analog TV or stream capture on dual tuners.\n");
3900 has_video = false;
3901 }
3902
3903
3904 if (has_video) {
3905 if (!dev->analog_ep_isoc || (try_bulk && dev->analog_ep_bulk))
3906 dev->analog_xfer_bulk = 1;
3907 dev_info(&intf->dev, "analog set to %s mode.\n",
3908 dev->analog_xfer_bulk ? "bulk" : "isoc");
3909 }
3910 if (has_dvb) {
3911 if (!dev->dvb_ep_isoc || (try_bulk && dev->dvb_ep_bulk))
3912 dev->dvb_xfer_bulk = 1;
3913 dev_info(&intf->dev, "dvb set to %s mode.\n",
3914 dev->dvb_xfer_bulk ? "bulk" : "isoc");
3915 }
3916
3917 if (dev->board.has_dual_ts && em28xx_duplicate_dev(dev) == 0) {
3918 dev->dev_next->ts = SECONDARY_TS;
3919 dev->dev_next->alt = -1;
3920 dev->dev_next->is_audio_only = has_vendor_audio &&
3921 !(has_video || has_dvb);
3922 dev->dev_next->has_video = false;
3923 dev->dev_next->ifnum = ifnum;
3924 dev->dev_next->model = id->driver_info;
3925
3926 mutex_init(&dev->dev_next->lock);
3927 retval = em28xx_init_dev(dev->dev_next, udev, intf,
3928 dev->dev_next->devno);
3929 if (retval)
3930 goto err_free;
3931
3932 dev->dev_next->board.ir_codes = NULL;
3933 dev->dev_next->board.has_ir_i2c = 0;
3934
3935 if (usb_xfer_mode < 0) {
3936 if (dev->dev_next->is_webcam)
3937 try_bulk = 1;
3938 else
3939 try_bulk = 0;
3940 } else {
3941 try_bulk = usb_xfer_mode > 0;
3942 }
3943
3944
3945 if (has_dvb) {
3946 if (!dev->dvb_ep_isoc_ts2 ||
3947 (try_bulk && dev->dvb_ep_bulk_ts2))
3948 dev->dev_next->dvb_xfer_bulk = 1;
3949 dev_info(&dev->intf->dev, "dvb ts2 set to %s mode.\n",
3950 dev->dev_next->dvb_xfer_bulk ? "bulk" : "isoc");
3951 }
3952
3953 dev->dev_next->dvb_ep_isoc = dev->dvb_ep_isoc_ts2;
3954 dev->dev_next->dvb_ep_bulk = dev->dvb_ep_bulk_ts2;
3955 dev->dev_next->dvb_max_pkt_size_isoc = dev->dvb_max_pkt_size_isoc_ts2;
3956 dev->dev_next->dvb_alt_isoc = dev->dvb_alt_isoc;
3957
3958
3959 if (dev->dvb_xfer_bulk) {
3960
3961 em28xx_write_reg(dev, 0x0b, 0x96);
3962 mdelay(100);
3963 em28xx_write_reg(dev, 0x0b, 0x80);
3964 mdelay(100);
3965 } else {
3966
3967 em28xx_write_reg(dev, 0x0b, 0x96);
3968 mdelay(100);
3969 em28xx_write_reg(dev, 0x0b, 0x82);
3970 mdelay(100);
3971 }
3972
3973 kref_init(&dev->dev_next->ref);
3974 }
3975
3976 kref_init(&dev->ref);
3977
3978 request_modules(dev);
3979
3980
3981
3982
3983
3984
3985 #ifdef CONFIG_MEDIA_CONTROLLER
3986 retval = media_device_register(dev->media_dev);
3987 #endif
3988
3989 return 0;
3990
3991 err_free:
3992 kfree(dev->alt_max_pkt_size_isoc);
3993 kfree(dev);
3994
3995 err:
3996 clear_bit(nr, em28xx_devused);
3997
3998 err_no_slot:
3999 usb_put_dev(udev);
4000 return retval;
4001 }
4002
4003
4004
4005
4006
4007
4008 static void em28xx_usb_disconnect(struct usb_interface *intf)
4009 {
4010 struct em28xx *dev;
4011
4012 dev = usb_get_intfdata(intf);
4013 usb_set_intfdata(intf, NULL);
4014
4015 if (!dev)
4016 return;
4017
4018 if (dev->dev_next) {
4019 dev->dev_next->disconnected = 1;
4020 dev_info(&dev->intf->dev, "Disconnecting %s\n",
4021 dev->dev_next->name);
4022 }
4023
4024 dev->disconnected = 1;
4025
4026 dev_info(&dev->intf->dev, "Disconnecting %s\n", dev->name);
4027
4028 flush_request_modules(dev);
4029
4030 em28xx_close_extension(dev);
4031
4032 if (dev->dev_next)
4033 em28xx_release_resources(dev->dev_next);
4034 em28xx_release_resources(dev);
4035
4036 if (dev->dev_next) {
4037 kref_put(&dev->dev_next->ref, em28xx_free_device);
4038 dev->dev_next = NULL;
4039 }
4040 kref_put(&dev->ref, em28xx_free_device);
4041 }
4042
4043 static int em28xx_usb_suspend(struct usb_interface *intf,
4044 pm_message_t message)
4045 {
4046 struct em28xx *dev;
4047
4048 dev = usb_get_intfdata(intf);
4049 if (!dev)
4050 return 0;
4051 em28xx_suspend_extension(dev);
4052 return 0;
4053 }
4054
4055 static int em28xx_usb_resume(struct usb_interface *intf)
4056 {
4057 struct em28xx *dev;
4058
4059 dev = usb_get_intfdata(intf);
4060 if (!dev)
4061 return 0;
4062 em28xx_resume_extension(dev);
4063 return 0;
4064 }
4065
4066 static struct usb_driver em28xx_usb_driver = {
4067 .name = "em28xx",
4068 .probe = em28xx_usb_probe,
4069 .disconnect = em28xx_usb_disconnect,
4070 .suspend = em28xx_usb_suspend,
4071 .resume = em28xx_usb_resume,
4072 .reset_resume = em28xx_usb_resume,
4073 .id_table = em28xx_id_table,
4074 };
4075
4076 module_usb_driver(em28xx_usb_driver);