drivers/media/usb/tm6000/tm6000-i2c.c

/* [<][>][^][v][top][bottom][index][help] */
This source file includes following definitions.
tm6000_i2c_send_regs
tm6000_i2c_recv_regs
tm6000_i2c_recv_regs16
tm6000_i2c_xfer
tm6000_i2c_eeprom
functionality
tm6000_i2c_register
tm6000_i2c_unregister
   1 // SPDX-License-Identifier: GPL-2.0
   2 // tm6000-i2c.c - driver for TM5600/TM6000/TM6010 USB video capture devices
   3 //
   4 // Copyright (c) 2006-2007 Mauro Carvalho Chehab <mchehab@kernel.org>
   5 //
   6 // Copyright (c) 2007 Michel Ludwig <michel.ludwig@gmail.com>
   7 //      - Fix SMBus Read Byte command
   8 
   9 #include <linux/module.h>
  10 #include <linux/kernel.h>
  11 #include <linux/usb.h>
  12 #include <linux/i2c.h>
  13 
  14 #include "tm6000.h"
  15 #include "tm6000-regs.h"
  16 #include <media/v4l2-common.h>
  17 #include <media/tuner.h>
  18 #include "tuner-xc2028.h"
  19 
  20 
  21 /* ----------------------------------------------------------- */
  22 
  23 static unsigned int i2c_debug;
  24 module_param(i2c_debug, int, 0644);
  25 MODULE_PARM_DESC(i2c_debug, "enable debug messages [i2c]");
  26 
  27 #define i2c_dprintk(lvl, fmt, args...) if (i2c_debug >= lvl) do { \
  28                         printk(KERN_DEBUG "%s at %s: " fmt, \
  29                         dev->name, __func__, ##args); } while (0)
  30 
  31 static int tm6000_i2c_send_regs(struct tm6000_core *dev, unsigned char addr,
  32                                 __u8 reg, char *buf, int len)
  33 {
  34         int rc;
  35         unsigned int i2c_packet_limit = 16;
  36 
  37         if (dev->dev_type == TM6010)
  38                 i2c_packet_limit = 80;
  39 
  40         if (!buf)
  41                 return -1;
  42 
  43         if (len < 1 || len > i2c_packet_limit) {
  44                 printk(KERN_ERR "Incorrect length of i2c packet = %d, limit set to %d\n",
  45                         len, i2c_packet_limit);
  46                 return -1;
  47         }
  48 
  49         /* capture mutex */
  50         rc = tm6000_read_write_usb(dev, USB_DIR_OUT | USB_TYPE_VENDOR |
  51                 USB_RECIP_DEVICE, REQ_16_SET_GET_I2C_WR1_RDN,
  52                 addr | reg << 8, 0, buf, len);
  53 
  54         if (rc < 0) {
  55                 /* release mutex */
  56                 return rc;
  57         }
  58 
  59         /* release mutex */
  60         return rc;
  61 }
  62 
  63 /* Generic read - doesn't work fine with 16bit registers */
  64 static int tm6000_i2c_recv_regs(struct tm6000_core *dev, unsigned char addr,
  65                                 __u8 reg, char *buf, int len)
  66 {
  67         int rc;
  68         u8 b[2];
  69         unsigned int i2c_packet_limit = 16;
  70 
  71         if (dev->dev_type == TM6010)
  72                 i2c_packet_limit = 64;
  73 
  74         if (!buf)
  75                 return -1;
  76 
  77         if (len < 1 || len > i2c_packet_limit) {
  78                 printk(KERN_ERR "Incorrect length of i2c packet = %d, limit set to %d\n",
  79                         len, i2c_packet_limit);
  80                 return -1;
  81         }
  82 
  83         /* capture mutex */
  84         if ((dev->caps.has_zl10353) && (dev->demod_addr << 1 == addr) && (reg % 2 == 0)) {
  85                 /*
  86                  * Workaround an I2C bug when reading from zl10353
  87                  */
  88                 reg -= 1;
  89                 len += 1;
  90 
  91                 rc = tm6000_read_write_usb(dev, USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
  92                         REQ_16_SET_GET_I2C_WR1_RDN, addr | reg << 8, 0, b, len);
  93 
  94                 *buf = b[1];
  95         } else {
  96                 rc = tm6000_read_write_usb(dev, USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
  97                         REQ_16_SET_GET_I2C_WR1_RDN, addr | reg << 8, 0, buf, len);
  98         }
  99 
 100         /* release mutex */
 101         return rc;
 102 }
 103 
 104 /*
 105  * read from a 16bit register
 106  * for example xc2028, xc3028 or xc3028L
 107  */
 108 static int tm6000_i2c_recv_regs16(struct tm6000_core *dev, unsigned char addr,
 109                                   __u16 reg, char *buf, int len)
 110 {
 111         int rc;
 112         unsigned char ureg;
 113 
 114         if (!buf || len != 2)
 115                 return -1;
 116 
 117         /* capture mutex */
 118         if (dev->dev_type == TM6010) {
 119                 ureg = reg & 0xFF;
 120                 rc = tm6000_read_write_usb(dev, USB_DIR_OUT | USB_TYPE_VENDOR |
 121                         USB_RECIP_DEVICE, REQ_16_SET_GET_I2C_WR1_RDN,
 122                         addr | (reg & 0xFF00), 0, &ureg, 1);
 123 
 124                 if (rc < 0) {
 125                         /* release mutex */
 126                         return rc;
 127                 }
 128 
 129                 rc = tm6000_read_write_usb(dev, USB_DIR_IN | USB_TYPE_VENDOR |
 130                         USB_RECIP_DEVICE, REQ_35_AFTEK_TUNER_READ,
 131                         reg, 0, buf, len);
 132         } else {
 133                 rc = tm6000_read_write_usb(dev, USB_DIR_IN | USB_TYPE_VENDOR |
 134                         USB_RECIP_DEVICE, REQ_14_SET_GET_I2C_WR2_RDN,
 135                         addr, reg, buf, len);
 136         }
 137 
 138         /* release mutex */
 139         return rc;
 140 }
 141 
 142 static int tm6000_i2c_xfer(struct i2c_adapter *i2c_adap,
 143                            struct i2c_msg msgs[], int num)
 144 {
 145         struct tm6000_core *dev = i2c_adap->algo_data;
 146         int addr, rc, i, byte;
 147 
 148         for (i = 0; i < num; i++) {
 149                 addr = (msgs[i].addr << 1) & 0xff;
 150                 i2c_dprintk(2, "%s %s addr=0x%x len=%d:",
 151                          (msgs[i].flags & I2C_M_RD) ? "read" : "write",
 152                          i == num - 1 ? "stop" : "nonstop", addr, msgs[i].len);
 153                 if (msgs[i].flags & I2C_M_RD) {
 154                         /* read request without preceding register selection */
 155                         /*
 156                          * The TM6000 only supports a read transaction
 157                          * immediately after a 1 or 2 byte write to select
 158                          * a register.  We cannot fulfill this request.
 159                          */
 160                         i2c_dprintk(2, " read without preceding write not supported");
 161                         rc = -EOPNOTSUPP;
 162                         goto err;
 163                 } else if (i + 1 < num && msgs[i].len <= 2 &&
 164                            (msgs[i + 1].flags & I2C_M_RD) &&
 165                            msgs[i].addr == msgs[i + 1].addr) {
 166                         /* 1 or 2 byte write followed by a read */
 167                         if (i2c_debug >= 2)
 168                                 for (byte = 0; byte < msgs[i].len; byte++)
 169                                         printk(KERN_CONT " %02x", msgs[i].buf[byte]);
 170                         i2c_dprintk(2, "; joined to read %s len=%d:",
 171                                     i == num - 2 ? "stop" : "nonstop",
 172                                     msgs[i + 1].len);
 173 
 174                         if (msgs[i].len == 2) {
 175                                 rc = tm6000_i2c_recv_regs16(dev, addr,
 176                                         msgs[i].buf[0] << 8 | msgs[i].buf[1],
 177                                         msgs[i + 1].buf, msgs[i + 1].len);
 178                         } else {
 179                                 rc = tm6000_i2c_recv_regs(dev, addr, msgs[i].buf[0],
 180                                         msgs[i + 1].buf, msgs[i + 1].len);
 181                         }
 182 
 183                         i++;
 184 
 185                         if (addr == dev->tuner_addr << 1) {
 186                                 tm6000_set_reg(dev, REQ_50_SET_START, 0, 0);
 187                                 tm6000_set_reg(dev, REQ_51_SET_STOP, 0, 0);
 188                         }
 189                         if (i2c_debug >= 2)
 190                                 for (byte = 0; byte < msgs[i].len; byte++)
 191                                         printk(KERN_CONT " %02x", msgs[i].buf[byte]);
 192                 } else {
 193                         /* write bytes */
 194                         if (i2c_debug >= 2)
 195                                 for (byte = 0; byte < msgs[i].len; byte++)
 196                                         printk(KERN_CONT " %02x", msgs[i].buf[byte]);
 197                         rc = tm6000_i2c_send_regs(dev, addr, msgs[i].buf[0],
 198                                 msgs[i].buf + 1, msgs[i].len - 1);
 199                 }
 200                 if (i2c_debug >= 2)
 201                         printk(KERN_CONT "\n");
 202                 if (rc < 0)
 203                         goto err;
 204         }
 205 
 206         return num;
 207 err:
 208         i2c_dprintk(2, " ERROR: %i\n", rc);
 209         return rc;
 210 }
 211 
 212 static int tm6000_i2c_eeprom(struct tm6000_core *dev)
 213 {
 214         int i, rc;
 215         unsigned char *p = dev->eedata;
 216         unsigned char bytes[17];
 217 
 218         dev->i2c_client.addr = 0xa0 >> 1;
 219         dev->eedata_size = 0;
 220 
 221         bytes[16] = '\0';
 222         for (i = 0; i < sizeof(dev->eedata); ) {
 223                 *p = i;
 224                 rc = tm6000_i2c_recv_regs(dev, 0xa0, i, p, 1);
 225                 if (rc < 1) {
 226                         if (p == dev->eedata)
 227                                 goto noeeprom;
 228                         else {
 229                                 printk(KERN_WARNING
 230                                 "%s: i2c eeprom read error (err=%d)\n",
 231                                 dev->name, rc);
 232                         }
 233                         return -EINVAL;
 234                 }
 235                 dev->eedata_size++;
 236                 p++;
 237                 if (0 == (i % 16))
 238                         printk(KERN_INFO "%s: i2c eeprom %02x:", dev->name, i);
 239                 printk(KERN_CONT " %02x", dev->eedata[i]);
 240                 if ((dev->eedata[i] >= ' ') && (dev->eedata[i] <= 'z'))
 241                         bytes[i%16] = dev->eedata[i];
 242                 else
 243                         bytes[i%16] = '.';
 244 
 245                 i++;
 246 
 247                 if (0 == (i % 16)) {
 248                         bytes[16] = '\0';
 249                         printk(KERN_CONT "  %s\n", bytes);
 250                 }
 251         }
 252         if (0 != (i%16)) {
 253                 bytes[i%16] = '\0';
 254                 for (i %= 16; i < 16; i++)
 255                         printk(KERN_CONT "   ");
 256                 printk(KERN_CONT "  %s\n", bytes);
 257         }
 258 
 259         return 0;
 260 
 261 noeeprom:
 262         printk(KERN_INFO "%s: Huh, no eeprom present (err=%d)?\n",
 263                dev->name, rc);
 264         return -EINVAL;
 265 }
 266 
 267 /* ----------------------------------------------------------- */
 268 
 269 /*
 270  * functionality()
 271  */
 272 static u32 functionality(struct i2c_adapter *adap)
 273 {
 274         return I2C_FUNC_SMBUS_EMUL;
 275 }
 276 
 277 static const struct i2c_algorithm tm6000_algo = {
 278         .master_xfer   = tm6000_i2c_xfer,
 279         .functionality = functionality,
 280 };
 281 
 282 /* ----------------------------------------------------------- */
 283 
 284 /*
 285  * tm6000_i2c_register()
 286  * register i2c bus
 287  */
 288 int tm6000_i2c_register(struct tm6000_core *dev)
 289 {
 290         int rc;
 291 
 292         dev->i2c_adap.owner = THIS_MODULE;
 293         dev->i2c_adap.algo = &tm6000_algo;
 294         dev->i2c_adap.dev.parent = &dev->udev->dev;
 295         strscpy(dev->i2c_adap.name, dev->name, sizeof(dev->i2c_adap.name));
 296         dev->i2c_adap.algo_data = dev;
 297         i2c_set_adapdata(&dev->i2c_adap, &dev->v4l2_dev);
 298         rc = i2c_add_adapter(&dev->i2c_adap);
 299         if (rc)
 300                 return rc;
 301 
 302         dev->i2c_client.adapter = &dev->i2c_adap;
 303         strscpy(dev->i2c_client.name, "tm6000 internal", I2C_NAME_SIZE);
 304         tm6000_i2c_eeprom(dev);
 305 
 306         return 0;
 307 }
 308 
 309 /*
 310  * tm6000_i2c_unregister()
 311  * unregister i2c_bus
 312  */
 313 int tm6000_i2c_unregister(struct tm6000_core *dev)
 314 {
 315         i2c_del_adapter(&dev->i2c_adap);
 316         return 0;
 317 }
/* [<][>][^][v][top][bottom][index][help] */
root/drivers/media/usb/tm6000/tm6000-i2c.c

DEFINITIONS
