root/drivers/power/supply/max8925_power.c

/* [<][>][^][v][top][bottom][index][help] */

DEFINITIONS

This source file includes following definitions.
  1. __set_charger
  2. max8925_charger_handler
  3. start_measure
  4. max8925_ac_get_prop
  5. max8925_usb_get_prop
  6. max8925_bat_get_prop
  7. max8925_init_charger
  8. max8925_deinit_charger
  9. max8925_power_dt_init
  10. max8925_power_dt_init
  11. max8925_power_probe
  12. max8925_power_remove

   1 // SPDX-License-Identifier: GPL-2.0-only
   2 /*
   3  * Battery driver for Maxim MAX8925
   4  *
   5  * Copyright (c) 2009-2010 Marvell International Ltd.
   6  *      Haojian Zhuang <haojian.zhuang@marvell.com>
   7  */
   8 
   9 #include <linux/module.h>
  10 #include <linux/err.h>
  11 #include <linux/slab.h>
  12 #include <linux/of.h>
  13 #include <linux/i2c.h>
  14 #include <linux/interrupt.h>
  15 #include <linux/platform_device.h>
  16 #include <linux/power_supply.h>
  17 #include <linux/mfd/max8925.h>
  18 
  19 /* registers in GPM */
  20 #define MAX8925_OUT5VEN                 0x54
  21 #define MAX8925_OUT3VEN                 0x58
  22 #define MAX8925_CHG_CNTL1               0x7c
  23 
  24 /* bits definition */
  25 #define MAX8925_CHG_STAT_VSYSLOW        (1 << 0)
  26 #define MAX8925_CHG_STAT_MODE_MASK      (3 << 2)
  27 #define MAX8925_CHG_STAT_EN_MASK        (1 << 4)
  28 #define MAX8925_CHG_MBDET               (1 << 1)
  29 #define MAX8925_CHG_AC_RANGE_MASK       (3 << 6)
  30 
  31 /* registers in ADC */
  32 #define MAX8925_ADC_RES_CNFG1           0x06
  33 #define MAX8925_ADC_AVG_CNFG1           0x07
  34 #define MAX8925_ADC_ACQ_CNFG1           0x08
  35 #define MAX8925_ADC_ACQ_CNFG2           0x09
  36 /* 2 bytes registers in below. MSB is 1st, LSB is 2nd. */
  37 #define MAX8925_ADC_AUX2                0x62
  38 #define MAX8925_ADC_VCHG                0x64
  39 #define MAX8925_ADC_VBBATT              0x66
  40 #define MAX8925_ADC_VMBATT              0x68
  41 #define MAX8925_ADC_ISNS                0x6a
  42 #define MAX8925_ADC_THM                 0x6c
  43 #define MAX8925_ADC_TDIE                0x6e
  44 #define MAX8925_CMD_AUX2                0xc8
  45 #define MAX8925_CMD_VCHG                0xd0
  46 #define MAX8925_CMD_VBBATT              0xd8
  47 #define MAX8925_CMD_VMBATT              0xe0
  48 #define MAX8925_CMD_ISNS                0xe8
  49 #define MAX8925_CMD_THM                 0xf0
  50 #define MAX8925_CMD_TDIE                0xf8
  51 
  52 enum {
  53         MEASURE_AUX2,
  54         MEASURE_VCHG,
  55         MEASURE_VBBATT,
  56         MEASURE_VMBATT,
  57         MEASURE_ISNS,
  58         MEASURE_THM,
  59         MEASURE_TDIE,
  60         MEASURE_MAX,
  61 };
  62 
  63 struct max8925_power_info {
  64         struct max8925_chip     *chip;
  65         struct i2c_client       *gpm;
  66         struct i2c_client       *adc;
  67 
  68         struct power_supply     *ac;
  69         struct power_supply     *usb;
  70         struct power_supply     *battery;
  71         int                     irq_base;
  72         unsigned                ac_online:1;
  73         unsigned                usb_online:1;
  74         unsigned                bat_online:1;
  75         unsigned                chg_mode:2;
  76         unsigned                batt_detect:1;  /* detecing MB by ID pin */
  77         unsigned                topoff_threshold:2;
  78         unsigned                fast_charge:3;
  79         unsigned                no_temp_support:1;
  80         unsigned                no_insert_detect:1;
  81 
  82         int (*set_charger) (int);
  83 };
  84 
  85 static int __set_charger(struct max8925_power_info *info, int enable)
  86 {
  87         struct max8925_chip *chip = info->chip;
  88         if (enable) {
  89                 /* enable charger in platform */
  90                 if (info->set_charger)
  91                         info->set_charger(1);
  92                 /* enable charger */
  93                 max8925_set_bits(info->gpm, MAX8925_CHG_CNTL1, 1 << 7, 0);
  94         } else {
  95                 /* disable charge */
  96                 max8925_set_bits(info->gpm, MAX8925_CHG_CNTL1, 1 << 7, 1 << 7);
  97                 if (info->set_charger)
  98                         info->set_charger(0);
  99         }
 100         dev_dbg(chip->dev, "%s\n", (enable) ? "Enable charger"
 101                 : "Disable charger");
 102         return 0;
 103 }
 104 
 105 static irqreturn_t max8925_charger_handler(int irq, void *data)
 106 {
 107         struct max8925_power_info *info = (struct max8925_power_info *)data;
 108         struct max8925_chip *chip = info->chip;
 109 
 110         switch (irq - chip->irq_base) {
 111         case MAX8925_IRQ_VCHG_DC_R:
 112                 info->ac_online = 1;
 113                 __set_charger(info, 1);
 114                 dev_dbg(chip->dev, "Adapter inserted\n");
 115                 break;
 116         case MAX8925_IRQ_VCHG_DC_F:
 117                 info->ac_online = 0;
 118                 __set_charger(info, 0);
 119                 dev_dbg(chip->dev, "Adapter removed\n");
 120                 break;
 121         case MAX8925_IRQ_VCHG_THM_OK_F:
 122                 /* Battery is not ready yet */
 123                 dev_dbg(chip->dev, "Battery temperature is out of range\n");
 124                 /* Fall through */
 125         case MAX8925_IRQ_VCHG_DC_OVP:
 126                 dev_dbg(chip->dev, "Error detection\n");
 127                 __set_charger(info, 0);
 128                 break;
 129         case MAX8925_IRQ_VCHG_THM_OK_R:
 130                 /* Battery is ready now */
 131                 dev_dbg(chip->dev, "Battery temperature is in range\n");
 132                 break;
 133         case MAX8925_IRQ_VCHG_SYSLOW_R:
 134                 /* VSYS is low */
 135                 dev_info(chip->dev, "Sys power is too low\n");
 136                 break;
 137         case MAX8925_IRQ_VCHG_SYSLOW_F:
 138                 dev_dbg(chip->dev, "Sys power is above low threshold\n");
 139                 break;
 140         case MAX8925_IRQ_VCHG_DONE:
 141                 __set_charger(info, 0);
 142                 dev_dbg(chip->dev, "Charging is done\n");
 143                 break;
 144         case MAX8925_IRQ_VCHG_TOPOFF:
 145                 dev_dbg(chip->dev, "Charging in top-off mode\n");
 146                 break;
 147         case MAX8925_IRQ_VCHG_TMR_FAULT:
 148                 __set_charger(info, 0);
 149                 dev_dbg(chip->dev, "Safe timer is expired\n");
 150                 break;
 151         case MAX8925_IRQ_VCHG_RST:
 152                 __set_charger(info, 0);
 153                 dev_dbg(chip->dev, "Charger is reset\n");
 154                 break;
 155         }
 156         return IRQ_HANDLED;
 157 }
 158 
 159 static int start_measure(struct max8925_power_info *info, int type)
 160 {
 161         unsigned char buf[2] = {0, 0};
 162         int meas_cmd;
 163         int meas_reg = 0, ret;
 164 
 165         switch (type) {
 166         case MEASURE_VCHG:
 167                 meas_cmd = MAX8925_CMD_VCHG;
 168                 meas_reg = MAX8925_ADC_VCHG;
 169                 break;
 170         case MEASURE_VBBATT:
 171                 meas_cmd = MAX8925_CMD_VBBATT;
 172                 meas_reg = MAX8925_ADC_VBBATT;
 173                 break;
 174         case MEASURE_VMBATT:
 175                 meas_cmd = MAX8925_CMD_VMBATT;
 176                 meas_reg = MAX8925_ADC_VMBATT;
 177                 break;
 178         case MEASURE_ISNS:
 179                 meas_cmd = MAX8925_CMD_ISNS;
 180                 meas_reg = MAX8925_ADC_ISNS;
 181                 break;
 182         default:
 183                 return -EINVAL;
 184         }
 185 
 186         max8925_reg_write(info->adc, meas_cmd, 0);
 187         max8925_bulk_read(info->adc, meas_reg, 2, buf);
 188         ret = ((buf[0]<<8) | buf[1]) >> 4;
 189 
 190         return ret;
 191 }
 192 
 193 static int max8925_ac_get_prop(struct power_supply *psy,
 194                                enum power_supply_property psp,
 195                                union power_supply_propval *val)
 196 {
 197         struct max8925_power_info *info = dev_get_drvdata(psy->dev.parent);
 198         int ret = 0;
 199 
 200         switch (psp) {
 201         case POWER_SUPPLY_PROP_ONLINE:
 202                 val->intval = info->ac_online;
 203                 break;
 204         case POWER_SUPPLY_PROP_VOLTAGE_NOW:
 205                 if (info->ac_online) {
 206                         ret = start_measure(info, MEASURE_VCHG);
 207                         if (ret >= 0) {
 208                                 val->intval = ret * 2000;       /* unit is uV */
 209                                 goto out;
 210                         }
 211                 }
 212                 ret = -ENODATA;
 213                 break;
 214         default:
 215                 ret = -ENODEV;
 216                 break;
 217         }
 218 out:
 219         return ret;
 220 }
 221 
 222 static enum power_supply_property max8925_ac_props[] = {
 223         POWER_SUPPLY_PROP_ONLINE,
 224         POWER_SUPPLY_PROP_VOLTAGE_NOW,
 225 };
 226 
 227 static int max8925_usb_get_prop(struct power_supply *psy,
 228                                 enum power_supply_property psp,
 229                                 union power_supply_propval *val)
 230 {
 231         struct max8925_power_info *info = dev_get_drvdata(psy->dev.parent);
 232         int ret = 0;
 233 
 234         switch (psp) {
 235         case POWER_SUPPLY_PROP_ONLINE:
 236                 val->intval = info->usb_online;
 237                 break;
 238         case POWER_SUPPLY_PROP_VOLTAGE_NOW:
 239                 if (info->usb_online) {
 240                         ret = start_measure(info, MEASURE_VCHG);
 241                         if (ret >= 0) {
 242                                 val->intval = ret * 2000;       /* unit is uV */
 243                                 goto out;
 244                         }
 245                 }
 246                 ret = -ENODATA;
 247                 break;
 248         default:
 249                 ret = -ENODEV;
 250                 break;
 251         }
 252 out:
 253         return ret;
 254 }
 255 
 256 static enum power_supply_property max8925_usb_props[] = {
 257         POWER_SUPPLY_PROP_ONLINE,
 258         POWER_SUPPLY_PROP_VOLTAGE_NOW,
 259 };
 260 
 261 static int max8925_bat_get_prop(struct power_supply *psy,
 262                                 enum power_supply_property psp,
 263                                 union power_supply_propval *val)
 264 {
 265         struct max8925_power_info *info = dev_get_drvdata(psy->dev.parent);
 266         int ret = 0;
 267 
 268         switch (psp) {
 269         case POWER_SUPPLY_PROP_ONLINE:
 270                 val->intval = info->bat_online;
 271                 break;
 272         case POWER_SUPPLY_PROP_VOLTAGE_NOW:
 273                 if (info->bat_online) {
 274                         ret = start_measure(info, MEASURE_VMBATT);
 275                         if (ret >= 0) {
 276                                 val->intval = ret * 2000;       /* unit is uV */
 277                                 ret = 0;
 278                                 break;
 279                         }
 280                 }
 281                 ret = -ENODATA;
 282                 break;
 283         case POWER_SUPPLY_PROP_CURRENT_NOW:
 284                 if (info->bat_online) {
 285                         ret = start_measure(info, MEASURE_ISNS);
 286                         if (ret >= 0) {
 287                                 /* assume r_sns is 0.02 */
 288                                 ret = ((ret * 6250) - 3125) /* uA */;
 289                                 val->intval = 0;
 290                                 if (ret > 0)
 291                                         val->intval = ret; /* unit is mA */
 292                                 ret = 0;
 293                                 break;
 294                         }
 295                 }
 296                 ret = -ENODATA;
 297                 break;
 298         case POWER_SUPPLY_PROP_CHARGE_TYPE:
 299                 if (!info->bat_online) {
 300                         ret = -ENODATA;
 301                         break;
 302                 }
 303                 ret = max8925_reg_read(info->gpm, MAX8925_CHG_STATUS);
 304                 ret = (ret & MAX8925_CHG_STAT_MODE_MASK) >> 2;
 305                 switch (ret) {
 306                 case 1:
 307                         val->intval = POWER_SUPPLY_CHARGE_TYPE_FAST;
 308                         break;
 309                 case 0:
 310                 case 2:
 311                         val->intval = POWER_SUPPLY_CHARGE_TYPE_TRICKLE;
 312                         break;
 313                 case 3:
 314                         val->intval = POWER_SUPPLY_CHARGE_TYPE_NONE;
 315                         break;
 316                 }
 317                 ret = 0;
 318                 break;
 319         case POWER_SUPPLY_PROP_STATUS:
 320                 if (!info->bat_online) {
 321                         ret = -ENODATA;
 322                         break;
 323                 }
 324                 ret = max8925_reg_read(info->gpm, MAX8925_CHG_STATUS);
 325                 if (info->usb_online || info->ac_online) {
 326                         val->intval = POWER_SUPPLY_STATUS_NOT_CHARGING;
 327                         if (ret & MAX8925_CHG_STAT_EN_MASK)
 328                                 val->intval = POWER_SUPPLY_STATUS_CHARGING;
 329                 } else
 330                         val->intval = POWER_SUPPLY_STATUS_DISCHARGING;
 331                 ret = 0;
 332                 break;
 333         default:
 334                 ret = -ENODEV;
 335                 break;
 336         }
 337         return ret;
 338 }
 339 
 340 static enum power_supply_property max8925_battery_props[] = {
 341         POWER_SUPPLY_PROP_ONLINE,
 342         POWER_SUPPLY_PROP_VOLTAGE_NOW,
 343         POWER_SUPPLY_PROP_CURRENT_NOW,
 344         POWER_SUPPLY_PROP_CHARGE_TYPE,
 345         POWER_SUPPLY_PROP_STATUS,
 346 };
 347 
 348 static const struct power_supply_desc ac_desc = {
 349         .name           = "max8925-ac",
 350         .type           = POWER_SUPPLY_TYPE_MAINS,
 351         .properties     = max8925_ac_props,
 352         .num_properties = ARRAY_SIZE(max8925_ac_props),
 353         .get_property   = max8925_ac_get_prop,
 354 };
 355 
 356 static const struct power_supply_desc usb_desc = {
 357         .name           = "max8925-usb",
 358         .type           = POWER_SUPPLY_TYPE_USB,
 359         .properties     = max8925_usb_props,
 360         .num_properties = ARRAY_SIZE(max8925_usb_props),
 361         .get_property   = max8925_usb_get_prop,
 362 };
 363 
 364 static const struct power_supply_desc battery_desc = {
 365         .name           = "max8925-battery",
 366         .type           = POWER_SUPPLY_TYPE_BATTERY,
 367         .properties     = max8925_battery_props,
 368         .num_properties = ARRAY_SIZE(max8925_battery_props),
 369         .get_property   = max8925_bat_get_prop,
 370 };
 371 
 372 #define REQUEST_IRQ(_irq, _name)                                        \
 373 do {                                                                    \
 374         ret = request_threaded_irq(chip->irq_base + _irq, NULL,         \
 375                                     max8925_charger_handler,            \
 376                                     IRQF_ONESHOT, _name, info);         \
 377         if (ret)                                                        \
 378                 dev_err(chip->dev, "Failed to request IRQ #%d: %d\n",   \
 379                         _irq, ret);                                     \
 380 } while (0)
 381 
 382 static int max8925_init_charger(struct max8925_chip *chip,
 383                                           struct max8925_power_info *info)
 384 {
 385         int ret;
 386 
 387         REQUEST_IRQ(MAX8925_IRQ_VCHG_DC_OVP, "ac-ovp");
 388         if (!info->no_insert_detect) {
 389                 REQUEST_IRQ(MAX8925_IRQ_VCHG_DC_F, "ac-remove");
 390                 REQUEST_IRQ(MAX8925_IRQ_VCHG_DC_R, "ac-insert");
 391         }
 392         if (!info->no_temp_support) {
 393                 REQUEST_IRQ(MAX8925_IRQ_VCHG_THM_OK_R, "batt-temp-in-range");
 394                 REQUEST_IRQ(MAX8925_IRQ_VCHG_THM_OK_F, "batt-temp-out-range");
 395         }
 396         REQUEST_IRQ(MAX8925_IRQ_VCHG_SYSLOW_F, "vsys-high");
 397         REQUEST_IRQ(MAX8925_IRQ_VCHG_SYSLOW_R, "vsys-low");
 398         REQUEST_IRQ(MAX8925_IRQ_VCHG_RST, "charger-reset");
 399         REQUEST_IRQ(MAX8925_IRQ_VCHG_DONE, "charger-done");
 400         REQUEST_IRQ(MAX8925_IRQ_VCHG_TOPOFF, "charger-topoff");
 401         REQUEST_IRQ(MAX8925_IRQ_VCHG_TMR_FAULT, "charger-timer-expire");
 402 
 403         info->usb_online = 0;
 404         info->bat_online = 0;
 405 
 406         /* check for power - can miss interrupt at boot time */
 407         if (start_measure(info, MEASURE_VCHG) * 2000 > 500000)
 408                 info->ac_online = 1;
 409         else
 410                 info->ac_online = 0;
 411 
 412         ret = max8925_reg_read(info->gpm, MAX8925_CHG_STATUS);
 413         if (ret >= 0) {
 414                 /*
 415                  * If battery detection is enabled, ID pin of battery is
 416                  * connected to MBDET pin of MAX8925. It could be used to
 417                  * detect battery presence.
 418                  * Otherwise, we have to assume that battery is always on.
 419                  */
 420                 if (info->batt_detect)
 421                         info->bat_online = (ret & MAX8925_CHG_MBDET) ? 0 : 1;
 422                 else
 423                         info->bat_online = 1;
 424                 if (ret & MAX8925_CHG_AC_RANGE_MASK)
 425                         info->ac_online = 1;
 426                 else
 427                         info->ac_online = 0;
 428         }
 429         /* disable charge */
 430         max8925_set_bits(info->gpm, MAX8925_CHG_CNTL1, 1 << 7, 1 << 7);
 431         /* set charging current in charge topoff mode */
 432         max8925_set_bits(info->gpm, MAX8925_CHG_CNTL1, 3 << 5,
 433                          info->topoff_threshold << 5);
 434         /* set charing current in fast charge mode */
 435         max8925_set_bits(info->gpm, MAX8925_CHG_CNTL1, 7, info->fast_charge);
 436 
 437         return 0;
 438 }
 439 
 440 static int max8925_deinit_charger(struct max8925_power_info *info)
 441 {
 442         struct max8925_chip *chip = info->chip;
 443         int irq;
 444 
 445         irq = chip->irq_base + MAX8925_IRQ_VCHG_DC_OVP;
 446         for (; irq <= chip->irq_base + MAX8925_IRQ_VCHG_TMR_FAULT; irq++)
 447                 free_irq(irq, info);
 448 
 449         return 0;
 450 }
 451 
 452 #ifdef CONFIG_OF
 453 static struct max8925_power_pdata *
 454 max8925_power_dt_init(struct platform_device *pdev)
 455 {
 456         struct device_node *nproot = pdev->dev.parent->of_node;
 457         struct device_node *np;
 458         int batt_detect;
 459         int topoff_threshold;
 460         int fast_charge;
 461         int no_temp_support;
 462         int no_insert_detect;
 463         struct max8925_power_pdata *pdata;
 464 
 465         if (!nproot)
 466                 return pdev->dev.platform_data;
 467 
 468         np = of_get_child_by_name(nproot, "charger");
 469         if (!np) {
 470                 dev_err(&pdev->dev, "failed to find charger node\n");
 471                 return NULL;
 472         }
 473 
 474         pdata = devm_kzalloc(&pdev->dev,
 475                         sizeof(struct max8925_power_pdata),
 476                         GFP_KERNEL);
 477         if (!pdata)
 478                 goto ret;
 479 
 480         of_property_read_u32(np, "topoff-threshold", &topoff_threshold);
 481         of_property_read_u32(np, "batt-detect", &batt_detect);
 482         of_property_read_u32(np, "fast-charge", &fast_charge);
 483         of_property_read_u32(np, "no-insert-detect", &no_insert_detect);
 484         of_property_read_u32(np, "no-temp-support", &no_temp_support);
 485 
 486         pdata->batt_detect = batt_detect;
 487         pdata->fast_charge = fast_charge;
 488         pdata->topoff_threshold = topoff_threshold;
 489         pdata->no_insert_detect = no_insert_detect;
 490         pdata->no_temp_support = no_temp_support;
 491 
 492 ret:
 493         of_node_put(np);
 494         return pdata;
 495 }
 496 #else
 497 static struct max8925_power_pdata *
 498 max8925_power_dt_init(struct platform_device *pdev)
 499 {
 500         return pdev->dev.platform_data;
 501 }
 502 #endif
 503 
 504 static int max8925_power_probe(struct platform_device *pdev)
 505 {
 506         struct max8925_chip *chip = dev_get_drvdata(pdev->dev.parent);
 507         struct power_supply_config psy_cfg = {}; /* Only for ac and usb */
 508         struct max8925_power_pdata *pdata = NULL;
 509         struct max8925_power_info *info;
 510         int ret;
 511 
 512         pdata = max8925_power_dt_init(pdev);
 513         if (!pdata) {
 514                 dev_err(&pdev->dev, "platform data isn't assigned to "
 515                         "power supply\n");
 516                 return -EINVAL;
 517         }
 518 
 519         info = devm_kzalloc(&pdev->dev, sizeof(struct max8925_power_info),
 520                                 GFP_KERNEL);
 521         if (!info)
 522                 return -ENOMEM;
 523         info->chip = chip;
 524         info->gpm = chip->i2c;
 525         info->adc = chip->adc;
 526         platform_set_drvdata(pdev, info);
 527 
 528         psy_cfg.supplied_to = pdata->supplied_to;
 529         psy_cfg.num_supplicants = pdata->num_supplicants;
 530 
 531         info->ac = power_supply_register(&pdev->dev, &ac_desc, &psy_cfg);
 532         if (IS_ERR(info->ac)) {
 533                 ret = PTR_ERR(info->ac);
 534                 goto out;
 535         }
 536         info->ac->dev.parent = &pdev->dev;
 537 
 538         info->usb = power_supply_register(&pdev->dev, &usb_desc, &psy_cfg);
 539         if (IS_ERR(info->usb)) {
 540                 ret = PTR_ERR(info->usb);
 541                 goto out_unregister_ac;
 542         }
 543         info->usb->dev.parent = &pdev->dev;
 544 
 545         info->battery = power_supply_register(&pdev->dev, &battery_desc, NULL);
 546         if (IS_ERR(info->battery)) {
 547                 ret = PTR_ERR(info->battery);
 548                 goto out_unregister_usb;
 549         }
 550         info->battery->dev.parent = &pdev->dev;
 551 
 552         info->batt_detect = pdata->batt_detect;
 553         info->topoff_threshold = pdata->topoff_threshold;
 554         info->fast_charge = pdata->fast_charge;
 555         info->set_charger = pdata->set_charger;
 556         info->no_temp_support = pdata->no_temp_support;
 557         info->no_insert_detect = pdata->no_insert_detect;
 558 
 559         max8925_init_charger(chip, info);
 560         return 0;
 561 out_unregister_usb:
 562         power_supply_unregister(info->usb);
 563 out_unregister_ac:
 564         power_supply_unregister(info->ac);
 565 out:
 566         return ret;
 567 }
 568 
 569 static int max8925_power_remove(struct platform_device *pdev)
 570 {
 571         struct max8925_power_info *info = platform_get_drvdata(pdev);
 572 
 573         if (info) {
 574                 power_supply_unregister(info->ac);
 575                 power_supply_unregister(info->usb);
 576                 power_supply_unregister(info->battery);
 577                 max8925_deinit_charger(info);
 578         }
 579         return 0;
 580 }
 581 
 582 static struct platform_driver max8925_power_driver = {
 583         .probe  = max8925_power_probe,
 584         .remove = max8925_power_remove,
 585         .driver = {
 586                 .name   = "max8925-power",
 587         },
 588 };
 589 
 590 module_platform_driver(max8925_power_driver);
 591 
 592 MODULE_LICENSE("GPL");
 593 MODULE_DESCRIPTION("Power supply driver for MAX8925");
 594 MODULE_ALIAS("platform:max8925-power");

/* [<][>][^][v][top][bottom][index][help] */