arch/m68k/coldfire/m528x.c

/* [<][>][^][v][top][bottom][index][help] */
This source file includes following definitions.
m528x_qspi_init
m528x_i2c_init
m528x_uarts_init
m528x_fec_init
wildfire_halt
wildfiremod_halt
config_BSP
   1 // SPDX-License-Identifier: GPL-2.0
   2 /***************************************************************************/
   3 
   4 /*
   5  *      m528x.c  -- platform support for ColdFire 528x based boards
   6  *
   7  *      Sub-architcture dependent initialization code for the Freescale
   8  *      5280, 5281 and 5282 CPUs.
   9  *
  10  *      Copyright (C) 1999-2003, Greg Ungerer (gerg@snapgear.com)
  11  *      Copyright (C) 2001-2003, SnapGear Inc. (www.snapgear.com)
  12  */
  13 
  14 /***************************************************************************/
  15 
  16 #include <linux/kernel.h>
  17 #include <linux/param.h>
  18 #include <linux/init.h>
  19 #include <linux/platform_device.h>
  20 #include <linux/io.h>
  21 #include <asm/machdep.h>
  22 #include <asm/coldfire.h>
  23 #include <asm/mcfsim.h>
  24 #include <asm/mcfuart.h>
  25 #include <asm/mcfclk.h>
  26 
  27 /***************************************************************************/
  28 
  29 DEFINE_CLK(pll, "pll.0", MCF_CLK);
  30 DEFINE_CLK(sys, "sys.0", MCF_BUSCLK);
  31 DEFINE_CLK(mcfpit0, "mcfpit.0", MCF_CLK);
  32 DEFINE_CLK(mcfpit1, "mcfpit.1", MCF_CLK);
  33 DEFINE_CLK(mcfpit2, "mcfpit.2", MCF_CLK);
  34 DEFINE_CLK(mcfpit3, "mcfpit.3", MCF_CLK);
  35 DEFINE_CLK(mcfuart0, "mcfuart.0", MCF_BUSCLK);
  36 DEFINE_CLK(mcfuart1, "mcfuart.1", MCF_BUSCLK);
  37 DEFINE_CLK(mcfuart2, "mcfuart.2", MCF_BUSCLK);
  38 DEFINE_CLK(mcfqspi0, "mcfqspi.0", MCF_BUSCLK);
  39 DEFINE_CLK(fec0, "fec.0", MCF_BUSCLK);
  40 DEFINE_CLK(mcfi2c0, "imx1-i2c.0", MCF_BUSCLK);
  41 
  42 struct clk *mcf_clks[] = {
  43         &clk_pll,
  44         &clk_sys,
  45         &clk_mcfpit0,
  46         &clk_mcfpit1,
  47         &clk_mcfpit2,
  48         &clk_mcfpit3,
  49         &clk_mcfuart0,
  50         &clk_mcfuart1,
  51         &clk_mcfuart2,
  52         &clk_mcfqspi0,
  53         &clk_fec0,
  54         &clk_mcfi2c0,
  55         NULL
  56 };
  57 
  58 /***************************************************************************/
  59 
  60 static void __init m528x_qspi_init(void)
  61 {
  62 #if IS_ENABLED(CONFIG_SPI_COLDFIRE_QSPI)
  63         /* setup Port QS for QSPI with gpio CS control */
  64         __raw_writeb(0x07, MCFGPIO_PQSPAR);
  65 #endif /* IS_ENABLED(CONFIG_SPI_COLDFIRE_QSPI) */
  66 }
  67 
  68 /***************************************************************************/
  69 
  70 static void __init m528x_i2c_init(void)
  71 {
  72 #if IS_ENABLED(CONFIG_I2C_IMX)
  73         u16 paspar;
  74 
  75         /* setup Port AS Pin Assignment Register for I2C */
  76         /*  set PASPA0 to SCL and PASPA1 to SDA */
  77         paspar = readw(MCFGPIO_PASPAR);
  78         paspar |= 0xF;
  79         writew(paspar, MCFGPIO_PASPAR);
  80 #endif /* IS_ENABLED(CONFIG_I2C_IMX) */
  81 }
  82 
  83 /***************************************************************************/
  84 
  85 static void __init m528x_uarts_init(void)
  86 {
  87         u8 port;
  88 
  89         /* make sure PUAPAR is set for UART0 and UART1 */
  90         port = readb(MCFGPIO_PUAPAR);
  91         port |= 0x03 | (0x03 << 2);
  92         writeb(port, MCFGPIO_PUAPAR);
  93 }
  94 
  95 /***************************************************************************/
  96 
  97 static void __init m528x_fec_init(void)
  98 {
  99         u16 v16;
 100 
 101         /* Set multi-function pins to ethernet mode for fec0 */
 102         v16 = readw(MCFGPIO_PASPAR);
 103         writew(v16 | 0xf00, MCFGPIO_PASPAR);
 104         writeb(0xc0, MCFGPIO_PEHLPAR);
 105 }
 106 
 107 /***************************************************************************/
 108 
 109 #ifdef CONFIG_WILDFIRE
 110 void wildfire_halt(void)
 111 {
 112         writeb(0, 0x30000007);
 113         writeb(0x2, 0x30000007);
 114 }
 115 #endif
 116 
 117 #ifdef CONFIG_WILDFIREMOD
 118 void wildfiremod_halt(void)
 119 {
 120         printk(KERN_INFO "WildFireMod hibernating...\n");
 121 
 122         /* Set portE.5 to Digital IO */
 123         writew(readw(MCFGPIO_PEPAR) & ~(1 << (5 * 2)), MCFGPIO_PEPAR);
 124 
 125         /* Make portE.5 an output */
 126         writeb(readb(MCFGPIO_PDDR_E) | (1 << 5), MCFGPIO_PDDR_E);
 127 
 128         /* Now toggle portE.5 from low to high */
 129         writeb(readb(MCFGPIO_PODR_E) & ~(1 << 5), MCFGPIO_PODR_E);
 130         writeb(readb(MCFGPIO_PODR_E) | (1 << 5), MCFGPIO_PODR_E);
 131 
 132         printk(KERN_EMERG "Failed to hibernate. Halting!\n");
 133 }
 134 #endif
 135 
 136 void __init config_BSP(char *commandp, int size)
 137 {
 138 #ifdef CONFIG_WILDFIRE
 139         mach_halt = wildfire_halt;
 140 #endif
 141 #ifdef CONFIG_WILDFIREMOD
 142         mach_halt = wildfiremod_halt;
 143 #endif
 144         mach_sched_init = hw_timer_init;
 145         m528x_uarts_init();
 146         m528x_fec_init();
 147         m528x_qspi_init();
 148         m528x_i2c_init();
 149 }
 150 
 151 /***************************************************************************/
/* [<][>][^][v][top][bottom][index][help] */
root/arch/m68k/coldfire/m528x.c

DEFINITIONS
