root/arch/arm/mach-footbridge/include/mach/hardware.h

INCLUDED FROM

   1 /* SPDX-License-Identifier: GPL-2.0-only */
   2 /*
   3  *  arch/arm/mach-footbridge/include/mach/hardware.h
   4  *
   5  *  Copyright (C) 1998-1999 Russell King.
   6  *
   7  *  This file contains the hardware definitions of the EBSA-285.
   8  */
   9 #ifndef __ASM_ARCH_HARDWARE_H
  10 #define __ASM_ARCH_HARDWARE_H
  11 
  12 /*   Virtual      Physical      Size
  13  * 0xff800000   0x40000000      1MB     X-Bus
  14  * 0xff000000   0x7c000000      1MB     PCI I/O space
  15  * 0xfe000000   0x42000000      1MB     CSR
  16  * 0xfd000000   0x78000000      1MB     Outbound write flush (not supported)
  17  * 0xfc000000   0x79000000      1MB     PCI IACK/special space
  18  * 0xfb000000   0x7a000000      16MB    PCI Config type 1
  19  * 0xfa000000   0x7b000000      16MB    PCI Config type 0
  20  * 0xf9000000   0x50000000      1MB     Cache flush
  21  * 0xf0000000   0x80000000      16MB    ISA memory
  22  */
  23 
  24 #ifdef CONFIG_MMU
  25 #define MMU_IO(a, b)    (a)
  26 #else
  27 #define MMU_IO(a, b)    (b)
  28 #endif
  29 
  30 #define XBUS_SIZE               0x00100000
  31 #define XBUS_BASE               MMU_IO(0xff800000, 0x40000000)
  32 
  33 #define ARMCSR_SIZE             0x00100000
  34 #define ARMCSR_BASE             MMU_IO(0xfe000000, 0x42000000)
  35 
  36 #define WFLUSH_SIZE             0x00100000
  37 #define WFLUSH_BASE             MMU_IO(0xfd000000, 0x78000000)
  38 
  39 #define PCIIACK_SIZE            0x00100000
  40 #define PCIIACK_BASE            MMU_IO(0xfc000000, 0x79000000)
  41 
  42 #define PCICFG1_SIZE            0x01000000
  43 #define PCICFG1_BASE            MMU_IO(0xfb000000, 0x7a000000)
  44 
  45 #define PCICFG0_SIZE            0x01000000
  46 #define PCICFG0_BASE            MMU_IO(0xfa000000, 0x7b000000)
  47 
  48 #define PCIMEM_SIZE             0x01000000
  49 #define PCIMEM_BASE             MMU_IO(0xf0000000, 0x80000000)
  50 
  51 #define XBUS_CS2                0x40012000
  52 
  53 #define XBUS_SWITCH             ((volatile unsigned char *)(XBUS_BASE + 0x12000))
  54 #define XBUS_SWITCH_SWITCH      ((*XBUS_SWITCH) & 15)
  55 #define XBUS_SWITCH_J17_13      ((*XBUS_SWITCH) & (1 << 4))
  56 #define XBUS_SWITCH_J17_11      ((*XBUS_SWITCH) & (1 << 5))
  57 #define XBUS_SWITCH_J17_9       ((*XBUS_SWITCH) & (1 << 6))
  58 
  59 #define UNCACHEABLE_ADDR        (ARMCSR_BASE + 0x108)   /* CSR_ROMBASEMASK */
  60 
  61 
  62 /* PIC irq control */
  63 #define PIC_LO                  0x20
  64 #define PIC_MASK_LO             0x21
  65 #define PIC_HI                  0xA0
  66 #define PIC_MASK_HI             0xA1
  67 
  68 /* GPIO pins */
  69 #define GPIO_CCLK               0x800
  70 #define GPIO_DSCLK              0x400
  71 #define GPIO_E2CLK              0x200
  72 #define GPIO_IOLOAD             0x100
  73 #define GPIO_RED_LED            0x080
  74 #define GPIO_WDTIMER            0x040
  75 #define GPIO_DATA               0x020
  76 #define GPIO_IOCLK              0x010
  77 #define GPIO_DONE               0x008
  78 #define GPIO_FAN                0x004
  79 #define GPIO_GREEN_LED          0x002
  80 #define GPIO_RESET              0x001
  81 
  82 /* CPLD pins */
  83 #define CPLD_DS_ENABLE          8
  84 #define CPLD_7111_DISABLE       4
  85 #define CPLD_UNMUTE             2
  86 #define CPLD_FLASH_WR_ENABLE    1
  87 
  88 #ifndef __ASSEMBLY__
  89 extern raw_spinlock_t nw_gpio_lock;
  90 extern void nw_gpio_modify_op(unsigned int mask, unsigned int set);
  91 extern void nw_gpio_modify_io(unsigned int mask, unsigned int in);
  92 extern unsigned int nw_gpio_read(void);
  93 extern void nw_cpld_modify(unsigned int mask, unsigned int set);
  94 #endif
  95 
  96 #endif