This source file includes following definitions.
- em7210_timer_init
- em7210_map_io
- em7210_pci_map_irq
- em7210_pci_init
- em7210_power_off
- em7210_request_gpios
- em7210_init_machine
1
2
3
4
5
6
7
8
9
10
11
12 #include <linux/mm.h>
13 #include <linux/init.h>
14 #include <linux/kernel.h>
15 #include <linux/pci.h>
16 #include <linux/pm.h>
17 #include <linux/serial_core.h>
18 #include <linux/serial_8250.h>
19 #include <linux/mtd/physmap.h>
20 #include <linux/platform_device.h>
21 #include <linux/i2c.h>
22 #include <linux/gpio.h>
23 #include <linux/gpio/machine.h>
24 #include <linux/io.h>
25 #include <linux/irq.h>
26 #include <asm/mach/arch.h>
27 #include <asm/mach/map.h>
28 #include <asm/mach/pci.h>
29 #include <asm/mach/time.h>
30 #include <asm/mach-types.h>
31
32 #include "hardware.h"
33 #include "gpio-iop32x.h"
34 #include "irqs.h"
35
36 static void __init em7210_timer_init(void)
37 {
38
39
40 iop_init_time(200000000);
41 }
42
43
44
45
46 static struct i2c_board_info __initdata em7210_i2c_devices[] = {
47 {
48 I2C_BOARD_INFO("rs5c372a", 0x32),
49 },
50 };
51
52
53
54
55 static struct map_desc em7210_io_desc[] __initdata = {
56 {
57 .virtual = IQ31244_UART,
58 .pfn = __phys_to_pfn(IQ31244_UART),
59 .length = 0x00100000,
60 .type = MT_DEVICE,
61 },
62 };
63
64 void __init em7210_map_io(void)
65 {
66 iop3xx_map_io();
67 iotable_init(em7210_io_desc, ARRAY_SIZE(em7210_io_desc));
68 }
69
70
71
72
73
74 #define INTA IRQ_IOP32X_XINT0
75 #define INTB IRQ_IOP32X_XINT1
76 #define INTC IRQ_IOP32X_XINT2
77 #define INTD IRQ_IOP32X_XINT3
78
79 static int __init
80 em7210_pci_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
81 {
82 static int pci_irq_table[][4] = {
83
84
85
86
87 {INTB, INTB, INTB, INTB},
88 {INTA, INTA, INTA, INTA},
89 {INTD, INTD, INTD, INTD},
90 {INTC, INTC, INTC, INTC},
91 {INTD, INTA, INTA, INTA},
92 {INTD, INTC, INTA, INTA},
93 };
94
95 if (pin < 1 || pin > 4)
96 return -1;
97
98 return pci_irq_table[slot % 6][pin - 1];
99 }
100
101 static struct hw_pci em7210_pci __initdata = {
102 .nr_controllers = 1,
103 .ops = &iop3xx_ops,
104 .setup = iop3xx_pci_setup,
105 .preinit = iop3xx_pci_preinit,
106 .map_irq = em7210_pci_map_irq,
107 };
108
109 static int __init em7210_pci_init(void)
110 {
111 if (machine_is_em7210())
112 pci_common_init(&em7210_pci);
113
114 return 0;
115 }
116
117 subsys_initcall(em7210_pci_init);
118
119
120
121
122
123 static struct physmap_flash_data em7210_flash_data = {
124 .width = 2,
125 };
126
127 static struct resource em7210_flash_resource = {
128 .start = 0xf0000000,
129 .end = 0xf1ffffff,
130 .flags = IORESOURCE_MEM,
131 };
132
133 static struct platform_device em7210_flash_device = {
134 .name = "physmap-flash",
135 .id = 0,
136 .dev = {
137 .platform_data = &em7210_flash_data,
138 },
139 .num_resources = 1,
140 .resource = &em7210_flash_resource,
141 };
142
143
144
145
146
147
148
149 static struct plat_serial8250_port em7210_serial_port[] = {
150 {
151 .mapbase = IQ31244_UART,
152 .membase = (char *)IQ31244_UART,
153 .irq = IRQ_IOP32X_XINT1,
154 .flags = UPF_SKIP_TEST,
155 .iotype = UPIO_MEM,
156 .regshift = 0,
157 .uartclk = 1843200,
158 },
159 { },
160 };
161
162 static struct resource em7210_uart_resource = {
163 .start = IQ31244_UART,
164 .end = IQ31244_UART + 7,
165 .flags = IORESOURCE_MEM,
166 };
167
168 static struct platform_device em7210_serial_device = {
169 .name = "serial8250",
170 .id = PLAT8250_DEV_PLATFORM,
171 .dev = {
172 .platform_data = em7210_serial_port,
173 },
174 .num_resources = 1,
175 .resource = &em7210_uart_resource,
176 };
177
178 #define EM7210_HARDWARE_POWER 0
179
180 void em7210_power_off(void)
181 {
182 int ret;
183
184 ret = gpio_direction_output(EM7210_HARDWARE_POWER, 1);
185 if (ret)
186 pr_crit("could not drive power off GPIO high\n");
187 }
188
189 static int __init em7210_request_gpios(void)
190 {
191 int ret;
192
193 if (!machine_is_em7210())
194 return 0;
195
196 ret = gpio_request(EM7210_HARDWARE_POWER, "power");
197 if (ret) {
198 pr_err("could not request power off GPIO\n");
199 return 0;
200 }
201
202 pm_power_off = em7210_power_off;
203
204 return 0;
205 }
206 device_initcall(em7210_request_gpios);
207
208 static void __init em7210_init_machine(void)
209 {
210 register_iop32x_gpio();
211 platform_device_register(&em7210_serial_device);
212 gpiod_add_lookup_table(&iop3xx_i2c0_gpio_lookup);
213 gpiod_add_lookup_table(&iop3xx_i2c1_gpio_lookup);
214 platform_device_register(&iop3xx_i2c0_device);
215 platform_device_register(&iop3xx_i2c1_device);
216 platform_device_register(&em7210_flash_device);
217 platform_device_register(&iop3xx_dma_0_channel);
218 platform_device_register(&iop3xx_dma_1_channel);
219
220 i2c_register_board_info(0, em7210_i2c_devices,
221 ARRAY_SIZE(em7210_i2c_devices));
222 }
223
224 MACHINE_START(EM7210, "Lanner EM7210")
225 .atag_offset = 0x100,
226 .map_io = em7210_map_io,
227 .init_irq = iop32x_init_irq,
228 .init_time = em7210_timer_init,
229 .init_machine = em7210_init_machine,
230 .restart = iop3xx_restart,
231 MACHINE_END