root/arch/arm/mach-pxa/mioa701.c

/* [<][>][^][v][top][bottom][index][help] */

DEFINITIONS

This source file includes following definitions.
  1. mioa701_lcd_power
  2. is_gsm_on
  3. gsm_on_irq
  4. gsm_init
  5. gsm_exit
  6. is_usb_connected
  7. install_bootstrap
  8. mioa701_sys_suspend
  9. mioa701_sys_resume
  10. bootstrap_init
  11. bootstrap_exit
  12. is_ac_connected
  13. mioa701_set_charge
  14. mioa701_poweroff
  15. mioa701_restart
  16. mioa701_machine_init
  17. mioa701_machine_exit

   1 // SPDX-License-Identifier: GPL-2.0-or-later
   2 /*
   3  * Handles the Mitac Mio A701 Board
   4  *
   5  * Copyright (C) 2008 Robert Jarzmik
   6  */
   7 
   8 #include <linux/kernel.h>
   9 #include <linux/init.h>
  10 #include <linux/platform_device.h>
  11 #include <linux/syscore_ops.h>
  12 #include <linux/input.h>
  13 #include <linux/delay.h>
  14 #include <linux/gpio_keys.h>
  15 #include <linux/pwm.h>
  16 #include <linux/pwm_backlight.h>
  17 #include <linux/rtc.h>
  18 #include <linux/leds.h>
  19 #include <linux/gpio.h>
  20 #include <linux/gpio/machine.h>
  21 #include <linux/interrupt.h>
  22 #include <linux/irq.h>
  23 #include <linux/pda_power.h>
  24 #include <linux/power_supply.h>
  25 #include <linux/wm97xx.h>
  26 #include <linux/mtd/physmap.h>
  27 #include <linux/usb/gpio_vbus.h>
  28 #include <linux/reboot.h>
  29 #include <linux/regulator/fixed.h>
  30 #include <linux/regulator/max1586.h>
  31 #include <linux/slab.h>
  32 #include <linux/platform_data/i2c-pxa.h>
  33 
  34 #include <asm/mach-types.h>
  35 #include <asm/mach/arch.h>
  36 
  37 #include "pxa27x.h"
  38 #include "regs-rtc.h"
  39 #include <linux/platform_data/keypad-pxa27x.h>
  40 #include <linux/platform_data/video-pxafb.h>
  41 #include <linux/platform_data/mmc-pxamci.h>
  42 #include "udc.h"
  43 #include "pxa27x-udc.h"
  44 #include <linux/platform_data/media/camera-pxa.h>
  45 #include <mach/audio.h>
  46 #include <mach/smemc.h>
  47 
  48 #include "mioa701.h"
  49 
  50 #include "generic.h"
  51 #include "devices.h"
  52 
  53 static unsigned long mioa701_pin_config[] = {
  54         /* Mio global */
  55         MIO_CFG_OUT(GPIO9_CHARGE_EN, AF0, DRIVE_LOW),
  56         MIO_CFG_OUT(GPIO18_POWEROFF, AF0, DRIVE_LOW),
  57         MFP_CFG_OUT(GPIO3, AF0, DRIVE_HIGH),
  58         MFP_CFG_OUT(GPIO4, AF0, DRIVE_HIGH),
  59         MIO_CFG_IN(GPIO80_MAYBE_CHARGE_VDROP, AF0),
  60 
  61         /* Backlight PWM 0 */
  62         GPIO16_PWM0_OUT,
  63 
  64         /* MMC */
  65         GPIO32_MMC_CLK,
  66         GPIO92_MMC_DAT_0,
  67         GPIO109_MMC_DAT_1,
  68         GPIO110_MMC_DAT_2,
  69         GPIO111_MMC_DAT_3,
  70         GPIO112_MMC_CMD,
  71         MIO_CFG_IN(GPIO78_SDIO_RO, AF0),
  72         MIO_CFG_IN(GPIO15_SDIO_INSERT, AF0),
  73         MIO_CFG_OUT(GPIO91_SDIO_EN, AF0, DRIVE_LOW),
  74 
  75         /* USB */
  76         MIO_CFG_IN(GPIO13_nUSB_DETECT, AF0),
  77         MIO_CFG_OUT(GPIO22_USB_ENABLE, AF0, DRIVE_LOW),
  78 
  79         /* LCD */
  80         GPIOxx_LCD_TFT_16BPP,
  81 
  82         /* QCI */
  83         GPIO12_CIF_DD_7,
  84         GPIO17_CIF_DD_6,
  85         GPIO50_CIF_DD_3,
  86         GPIO51_CIF_DD_2,
  87         GPIO52_CIF_DD_4,
  88         GPIO53_CIF_MCLK,
  89         GPIO54_CIF_PCLK,
  90         GPIO55_CIF_DD_1,
  91         GPIO81_CIF_DD_0,
  92         GPIO82_CIF_DD_5,
  93         GPIO84_CIF_FV,
  94         GPIO85_CIF_LV,
  95         MIO_CFG_OUT(GPIO56_MT9M111_nOE, AF0, DRIVE_LOW),
  96 
  97         /* Bluetooth */
  98         MIO_CFG_IN(GPIO14_BT_nACTIVITY, AF0),
  99         GPIO44_BTUART_CTS,
 100         GPIO42_BTUART_RXD,
 101         GPIO45_BTUART_RTS,
 102         GPIO43_BTUART_TXD,
 103         MIO_CFG_OUT(GPIO83_BT_ON, AF0, DRIVE_LOW),
 104         MIO_CFG_OUT(GPIO77_BT_UNKNOWN1, AF0, DRIVE_HIGH),
 105         MIO_CFG_OUT(GPIO86_BT_MAYBE_nRESET, AF0, DRIVE_HIGH),
 106 
 107         /* GPS */
 108         MIO_CFG_OUT(GPIO23_GPS_UNKNOWN1, AF0, DRIVE_LOW),
 109         MIO_CFG_OUT(GPIO26_GPS_ON, AF0, DRIVE_LOW),
 110         MIO_CFG_OUT(GPIO27_GPS_RESET, AF0, DRIVE_LOW),
 111         MIO_CFG_OUT(GPIO106_GPS_UNKNOWN2, AF0, DRIVE_LOW),
 112         MIO_CFG_OUT(GPIO107_GPS_UNKNOWN3, AF0, DRIVE_LOW),
 113         GPIO46_STUART_RXD,
 114         GPIO47_STUART_TXD,
 115 
 116         /* GSM */
 117         MIO_CFG_OUT(GPIO24_GSM_MOD_RESET_CMD, AF0, DRIVE_LOW),
 118         MIO_CFG_OUT(GPIO88_GSM_nMOD_ON_CMD, AF0, DRIVE_HIGH),
 119         MIO_CFG_OUT(GPIO90_GSM_nMOD_OFF_CMD, AF0, DRIVE_HIGH),
 120         MIO_CFG_OUT(GPIO114_GSM_nMOD_DTE_UART_STATE, AF0, DRIVE_HIGH),
 121         MIO_CFG_IN(GPIO25_GSM_MOD_ON_STATE, AF0),
 122         MIO_CFG_IN(GPIO113_GSM_EVENT, AF0) | WAKEUP_ON_EDGE_BOTH,
 123         GPIO34_FFUART_RXD,
 124         GPIO35_FFUART_CTS,
 125         GPIO36_FFUART_DCD,
 126         GPIO37_FFUART_DSR,
 127         GPIO39_FFUART_TXD,
 128         GPIO40_FFUART_DTR,
 129         GPIO41_FFUART_RTS,
 130 
 131         /* Sound */
 132         GPIO28_AC97_BITCLK,
 133         GPIO29_AC97_SDATA_IN_0,
 134         GPIO30_AC97_SDATA_OUT,
 135         GPIO31_AC97_SYNC,
 136         GPIO89_AC97_SYSCLK,
 137         MIO_CFG_IN(GPIO12_HPJACK_INSERT, AF0),
 138 
 139         /* Leds */
 140         MIO_CFG_OUT(GPIO10_LED_nCharging, AF0, DRIVE_HIGH),
 141         MIO_CFG_OUT(GPIO97_LED_nBlue, AF0, DRIVE_HIGH),
 142         MIO_CFG_OUT(GPIO98_LED_nOrange, AF0, DRIVE_HIGH),
 143         MIO_CFG_OUT(GPIO82_LED_nVibra, AF0, DRIVE_HIGH),
 144         MIO_CFG_OUT(GPIO115_LED_nKeyboard, AF0, DRIVE_HIGH),
 145 
 146         /* Keyboard */
 147         MIO_CFG_IN(GPIO0_KEY_POWER, AF0) | WAKEUP_ON_EDGE_BOTH,
 148         MIO_CFG_IN(GPIO93_KEY_VOLUME_UP, AF0),
 149         MIO_CFG_IN(GPIO94_KEY_VOLUME_DOWN, AF0),
 150         GPIO100_KP_MKIN_0,
 151         GPIO101_KP_MKIN_1,
 152         GPIO102_KP_MKIN_2,
 153         GPIO103_KP_MKOUT_0,
 154         GPIO104_KP_MKOUT_1,
 155         GPIO105_KP_MKOUT_2,
 156 
 157         /* I2C */
 158         GPIO117_I2C_SCL,
 159         GPIO118_I2C_SDA,
 160 
 161         /* Unknown */
 162         MFP_CFG_IN(GPIO20, AF0),
 163         MFP_CFG_IN(GPIO21, AF0),
 164         MFP_CFG_IN(GPIO33, AF0),
 165         MFP_CFG_OUT(GPIO49, AF0, DRIVE_HIGH),
 166         MFP_CFG_OUT(GPIO57, AF0, DRIVE_HIGH),
 167         MFP_CFG_IN(GPIO96, AF0),
 168         MFP_CFG_OUT(GPIO116, AF0, DRIVE_HIGH),
 169 };
 170 
 171 static struct pwm_lookup mioa701_pwm_lookup[] = {
 172         PWM_LOOKUP("pxa27x-pwm.0", 0, "pwm-backlight", NULL, 4000 * 1024,
 173                    PWM_POLARITY_NORMAL),
 174 };
 175 
 176 /* LCD Screen and Backlight */
 177 static struct platform_pwm_backlight_data mioa701_backlight_data = {
 178         .max_brightness = 100,
 179         .dft_brightness = 50,
 180         .enable_gpio    = -1,
 181 };
 182 
 183 /*
 184  * LTM0305A776C LCD panel timings
 185  *
 186  * see:
 187  *  - the LTM0305A776C datasheet,
 188  *  - and the PXA27x Programmers' manual
 189  */
 190 static struct pxafb_mode_info mioa701_ltm0305a776c = {
 191         .pixclock               = 220000,       /* CLK=4.545 MHz */
 192         .xres                   = 240,
 193         .yres                   = 320,
 194         .bpp                    = 16,
 195         .hsync_len              = 4,
 196         .vsync_len              = 2,
 197         .left_margin            = 6,
 198         .right_margin           = 4,
 199         .upper_margin           = 5,
 200         .lower_margin           = 3,
 201 };
 202 
 203 static void mioa701_lcd_power(int on, struct fb_var_screeninfo *si)
 204 {
 205         gpio_set_value(GPIO87_LCD_POWER, on);
 206 }
 207 
 208 static struct pxafb_mach_info mioa701_pxafb_info = {
 209         .modes                  = &mioa701_ltm0305a776c,
 210         .num_modes              = 1,
 211         .lcd_conn               = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL,
 212         .pxafb_lcd_power        = mioa701_lcd_power,
 213 };
 214 
 215 /*
 216  * Keyboard configuration
 217  */
 218 static const unsigned int mioa701_matrix_keys[] = {
 219         KEY(0, 0, KEY_UP),
 220         KEY(0, 1, KEY_RIGHT),
 221         KEY(0, 2, KEY_MEDIA),
 222         KEY(1, 0, KEY_DOWN),
 223         KEY(1, 1, KEY_ENTER),
 224         KEY(1, 2, KEY_CONNECT), /* GPS key */
 225         KEY(2, 0, KEY_LEFT),
 226         KEY(2, 1, KEY_PHONE),   /* Phone Green key */
 227         KEY(2, 2, KEY_CAMERA)   /* Camera key */
 228 };
 229 
 230 static struct matrix_keymap_data mioa701_matrix_keymap_data = {
 231         .keymap                 = mioa701_matrix_keys,
 232         .keymap_size            = ARRAY_SIZE(mioa701_matrix_keys),
 233 };
 234 
 235 static struct pxa27x_keypad_platform_data mioa701_keypad_info = {
 236         .matrix_key_rows = 3,
 237         .matrix_key_cols = 3,
 238         .matrix_keymap_data = &mioa701_matrix_keymap_data,
 239 };
 240 
 241 /*
 242  * GPIO Key Configuration
 243  */
 244 #define MIO_KEY(key, _gpio, _desc, _wakeup) \
 245         { .code = (key), .gpio = (_gpio), .active_low = 0, \
 246         .desc = (_desc), .type = EV_KEY, .wakeup = (_wakeup) }
 247 static struct gpio_keys_button mioa701_button_table[] = {
 248         MIO_KEY(KEY_EXIT, GPIO0_KEY_POWER, "Power button", 1),
 249         MIO_KEY(KEY_VOLUMEUP, GPIO93_KEY_VOLUME_UP, "Volume up", 0),
 250         MIO_KEY(KEY_VOLUMEDOWN, GPIO94_KEY_VOLUME_DOWN, "Volume down", 0),
 251         MIO_KEY(KEY_HP, GPIO12_HPJACK_INSERT, "HP jack detect", 0)
 252 };
 253 
 254 static struct gpio_keys_platform_data mioa701_gpio_keys_data = {
 255         .buttons  = mioa701_button_table,
 256         .nbuttons = ARRAY_SIZE(mioa701_button_table),
 257 };
 258 
 259 /*
 260  * Leds and vibrator
 261  */
 262 #define ONE_LED(_gpio, _name) \
 263 { .gpio = (_gpio), .name = (_name), .active_low = true }
 264 static struct gpio_led gpio_leds[] = {
 265         ONE_LED(GPIO10_LED_nCharging, "mioa701:charging"),
 266         ONE_LED(GPIO97_LED_nBlue, "mioa701:blue"),
 267         ONE_LED(GPIO98_LED_nOrange, "mioa701:orange"),
 268         ONE_LED(GPIO82_LED_nVibra, "mioa701:vibra"),
 269         ONE_LED(GPIO115_LED_nKeyboard, "mioa701:keyboard")
 270 };
 271 
 272 static struct gpio_led_platform_data gpio_led_info = {
 273         .leds = gpio_leds,
 274         .num_leds = ARRAY_SIZE(gpio_leds),
 275 };
 276 
 277 /*
 278  * GSM Sagem XS200 chip
 279  *
 280  * GSM handling was purged from kernel. For history, this is the way to go :
 281  *   - init : GPIO24_GSM_MOD_RESET_CMD = 0, GPIO114_GSM_nMOD_DTE_UART_STATE = 1
 282  *            GPIO88_GSM_nMOD_ON_CMD = 1, GPIO90_GSM_nMOD_OFF_CMD = 1
 283  *   - reset : GPIO24_GSM_MOD_RESET_CMD = 1, msleep(100),
 284  *             GPIO24_GSM_MOD_RESET_CMD = 0
 285  *   - turn on  : GPIO88_GSM_nMOD_ON_CMD = 0, msleep(1000),
 286  *                GPIO88_GSM_nMOD_ON_CMD = 1
 287  *   - turn off : GPIO90_GSM_nMOD_OFF_CMD = 0, msleep(1000),
 288  *                GPIO90_GSM_nMOD_OFF_CMD = 1
 289  */
 290 static int is_gsm_on(void)
 291 {
 292         int is_on;
 293 
 294         is_on = !!gpio_get_value(GPIO25_GSM_MOD_ON_STATE);
 295         return is_on;
 296 }
 297 
 298 irqreturn_t gsm_on_irq(int irq, void *p)
 299 {
 300         printk(KERN_DEBUG "Mioa701: GSM status changed to %s\n",
 301                is_gsm_on() ? "on" : "off");
 302         return IRQ_HANDLED;
 303 }
 304 
 305 static struct gpio gsm_gpios[] = {
 306         { GPIO25_GSM_MOD_ON_STATE, GPIOF_IN, "GSM state" },
 307         { GPIO113_GSM_EVENT, GPIOF_IN, "GSM event" },
 308 };
 309 
 310 static int __init gsm_init(void)
 311 {
 312         int rc;
 313 
 314         rc = gpio_request_array(ARRAY_AND_SIZE(gsm_gpios));
 315         if (rc)
 316                 goto err_gpio;
 317         rc = request_irq(gpio_to_irq(GPIO25_GSM_MOD_ON_STATE), gsm_on_irq,
 318                          IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
 319                          "GSM XS200 Power Irq", NULL);
 320         if (rc)
 321                 goto err_irq;
 322 
 323         gpio_set_wake(GPIO113_GSM_EVENT, 1);
 324         return 0;
 325 
 326 err_irq:
 327         printk(KERN_ERR "Mioa701: Can't request GSM_ON irq\n");
 328         gpio_free_array(ARRAY_AND_SIZE(gsm_gpios));
 329 err_gpio:
 330         printk(KERN_ERR "Mioa701: gsm not available\n");
 331         return rc;
 332 }
 333 
 334 static void gsm_exit(void)
 335 {
 336         free_irq(gpio_to_irq(GPIO25_GSM_MOD_ON_STATE), NULL);
 337         gpio_free_array(ARRAY_AND_SIZE(gsm_gpios));
 338 }
 339 
 340 /*
 341  * Bluetooth BRF6150 chip
 342  *
 343  * BT handling was purged from kernel. For history, this is the way to go :
 344  * - turn on  : GPIO83_BT_ON = 1
 345  * - turn off : GPIO83_BT_ON = 0
 346  */
 347 
 348 /*
 349  * GPS Sirf Star III chip
 350  *
 351  * GPS handling was purged from kernel. For history, this is the way to go :
 352  * - init : GPIO23_GPS_UNKNOWN1 = 1, GPIO26_GPS_ON = 0, GPIO27_GPS_RESET = 0
 353  *          GPIO106_GPS_UNKNOWN2 = 0, GPIO107_GPS_UNKNOWN3 = 0
 354  * - turn on  : GPIO27_GPS_RESET = 1, GPIO26_GPS_ON = 1
 355  * - turn off : GPIO26_GPS_ON = 0, GPIO27_GPS_RESET = 0
 356  */
 357 
 358 /*
 359  * USB UDC
 360  */
 361 static int is_usb_connected(void)
 362 {
 363         return !gpio_get_value(GPIO13_nUSB_DETECT);
 364 }
 365 
 366 static struct pxa2xx_udc_mach_info mioa701_udc_info = {
 367         .udc_is_connected = is_usb_connected,
 368         .gpio_pullup      = GPIO22_USB_ENABLE,
 369 };
 370 
 371 struct gpio_vbus_mach_info gpio_vbus_data = {
 372         .gpio_vbus = GPIO13_nUSB_DETECT,
 373         .gpio_vbus_inverted = 1,
 374         .gpio_pullup = -1,
 375 };
 376 
 377 /*
 378  * SDIO/MMC Card controller
 379  */
 380 /**
 381  * The card detect interrupt isn't debounced so we delay it by 250ms
 382  * to give the card a chance to fully insert/eject.
 383  */
 384 static struct pxamci_platform_data mioa701_mci_info = {
 385         .detect_delay_ms        = 250,
 386         .ocr_mask               = MMC_VDD_32_33 | MMC_VDD_33_34,
 387 };
 388 
 389 static struct gpiod_lookup_table mioa701_mci_gpio_table = {
 390         .dev_id = "pxa2xx-mci.0",
 391         .table = {
 392                 /* Card detect on GPIO 15 */
 393                 GPIO_LOOKUP("gpio-pxa", GPIO15_SDIO_INSERT,
 394                             "cd", GPIO_ACTIVE_LOW),
 395                 /* Write protect on GPIO 78 */
 396                 GPIO_LOOKUP("gpio-pxa", GPIO78_SDIO_RO,
 397                             "wp", GPIO_ACTIVE_LOW),
 398                 /* Power on GPIO 91 */
 399                 GPIO_LOOKUP("gpio-pxa", GPIO91_SDIO_EN,
 400                             "power", GPIO_ACTIVE_HIGH),
 401                 { },
 402         },
 403 };
 404 
 405 /* FlashRAM */
 406 static struct resource docg3_resource = {
 407         .start = PXA_CS0_PHYS,
 408         .end   = PXA_CS0_PHYS + SZ_8K - 1,
 409         .flags = IORESOURCE_MEM,
 410 };
 411 
 412 static struct platform_device docg3 = {
 413         .name          = "docg3",
 414         .id            = -1,
 415         .resource      = &docg3_resource,
 416         .num_resources = 1,
 417         .dev = {
 418                 .platform_data = NULL,
 419         },
 420 };
 421 
 422 /*
 423  * Suspend/Resume bootstrap management
 424  *
 425  * MIO A701 reboot sequence is highly ROM dependent. From the one dissassembled,
 426  * this sequence is as follows :
 427  *   - disables interrupts
 428  *   - initialize SDRAM (self refresh RAM into active RAM)
 429  *   - initialize GPIOs (depends on value at 0xa020b020)
 430  *   - initialize coprossessors
 431  *   - if edge detect on PWR_SCL(GPIO3), then proceed to cold start
 432  *   - or if value at 0xa020b000 not equal to 0x0f0f0f0f, proceed to cold start
 433  *   - else do a resume, ie. jump to addr 0xa0100000
 434  */
 435 #define RESUME_ENABLE_ADDR      0xa020b000
 436 #define RESUME_ENABLE_VAL       0x0f0f0f0f
 437 #define RESUME_BT_ADDR          0xa020b020
 438 #define RESUME_UNKNOWN_ADDR     0xa020b024
 439 #define RESUME_VECTOR_ADDR      0xa0100000
 440 #define BOOTSTRAP_WORDS         mioa701_bootstrap_lg/4
 441 
 442 static u32 *save_buffer;
 443 
 444 static void install_bootstrap(void)
 445 {
 446         int i;
 447         u32 *rom_bootstrap  = phys_to_virt(RESUME_VECTOR_ADDR);
 448         u32 *src = &mioa701_bootstrap;
 449 
 450         for (i = 0; i < BOOTSTRAP_WORDS; i++)
 451                 rom_bootstrap[i] = src[i];
 452 }
 453 
 454 
 455 static int mioa701_sys_suspend(void)
 456 {
 457         int i = 0, is_bt_on;
 458         u32 *mem_resume_vector  = phys_to_virt(RESUME_VECTOR_ADDR);
 459         u32 *mem_resume_enabler = phys_to_virt(RESUME_ENABLE_ADDR);
 460         u32 *mem_resume_bt      = phys_to_virt(RESUME_BT_ADDR);
 461         u32 *mem_resume_unknown = phys_to_virt(RESUME_UNKNOWN_ADDR);
 462 
 463         /* Devices prepare suspend */
 464         is_bt_on = !!gpio_get_value(GPIO83_BT_ON);
 465         pxa2xx_mfp_set_lpm(GPIO83_BT_ON,
 466                            is_bt_on ? MFP_LPM_DRIVE_HIGH : MFP_LPM_DRIVE_LOW);
 467 
 468         for (i = 0; i < BOOTSTRAP_WORDS; i++)
 469                 save_buffer[i] = mem_resume_vector[i];
 470         save_buffer[i++] = *mem_resume_enabler;
 471         save_buffer[i++] = *mem_resume_bt;
 472         save_buffer[i++] = *mem_resume_unknown;
 473 
 474         *mem_resume_enabler = RESUME_ENABLE_VAL;
 475         *mem_resume_bt      = is_bt_on;
 476 
 477         install_bootstrap();
 478         return 0;
 479 }
 480 
 481 static void mioa701_sys_resume(void)
 482 {
 483         int i = 0;
 484         u32 *mem_resume_vector  = phys_to_virt(RESUME_VECTOR_ADDR);
 485         u32 *mem_resume_enabler = phys_to_virt(RESUME_ENABLE_ADDR);
 486         u32 *mem_resume_bt      = phys_to_virt(RESUME_BT_ADDR);
 487         u32 *mem_resume_unknown = phys_to_virt(RESUME_UNKNOWN_ADDR);
 488 
 489         for (i = 0; i < BOOTSTRAP_WORDS; i++)
 490                 mem_resume_vector[i] = save_buffer[i];
 491         *mem_resume_enabler = save_buffer[i++];
 492         *mem_resume_bt      = save_buffer[i++];
 493         *mem_resume_unknown = save_buffer[i++];
 494 }
 495 
 496 static struct syscore_ops mioa701_syscore_ops = {
 497         .suspend        = mioa701_sys_suspend,
 498         .resume         = mioa701_sys_resume,
 499 };
 500 
 501 static int __init bootstrap_init(void)
 502 {
 503         int save_size = mioa701_bootstrap_lg + (sizeof(u32) * 3);
 504 
 505         register_syscore_ops(&mioa701_syscore_ops);
 506 
 507         save_buffer = kmalloc(save_size, GFP_KERNEL);
 508         if (!save_buffer)
 509                 return -ENOMEM;
 510         printk(KERN_INFO "MioA701: allocated %d bytes for bootstrap\n",
 511                save_size);
 512         return 0;
 513 }
 514 
 515 static void bootstrap_exit(void)
 516 {
 517         kfree(save_buffer);
 518         unregister_syscore_ops(&mioa701_syscore_ops);
 519 
 520         printk(KERN_CRIT "Unregistering mioa701 suspend will hang next"
 521                "resume !!!\n");
 522 }
 523 
 524 /*
 525  * Power Supply
 526  */
 527 static char *supplicants[] = {
 528         "mioa701_battery"
 529 };
 530 
 531 static int is_ac_connected(void)
 532 {
 533         return gpio_get_value(GPIO96_AC_DETECT);
 534 }
 535 
 536 static void mioa701_set_charge(int flags)
 537 {
 538         gpio_set_value(GPIO9_CHARGE_EN, (flags == PDA_POWER_CHARGE_USB));
 539 }
 540 
 541 static struct pda_power_pdata power_pdata = {
 542         .is_ac_online   = is_ac_connected,
 543         .is_usb_online  = is_usb_connected,
 544         .set_charge = mioa701_set_charge,
 545         .supplied_to = supplicants,
 546         .num_supplicants = ARRAY_SIZE(supplicants),
 547 };
 548 
 549 static struct resource power_resources[] = {
 550         [0] = {
 551                 .name   = "ac",
 552                 .start  = PXA_GPIO_TO_IRQ(GPIO96_AC_DETECT),
 553                 .end    = PXA_GPIO_TO_IRQ(GPIO96_AC_DETECT),
 554                 .flags  = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE |
 555                 IORESOURCE_IRQ_LOWEDGE,
 556         },
 557         [1] = {
 558                 .name   = "usb",
 559                 .start  = PXA_GPIO_TO_IRQ(GPIO13_nUSB_DETECT),
 560                 .end    = PXA_GPIO_TO_IRQ(GPIO13_nUSB_DETECT),
 561                 .flags  = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE |
 562                 IORESOURCE_IRQ_LOWEDGE,
 563         },
 564 };
 565 
 566 static struct platform_device power_dev = {
 567         .name           = "pda-power",
 568         .id             = -1,
 569         .resource       = power_resources,
 570         .num_resources  = ARRAY_SIZE(power_resources),
 571         .dev = {
 572                 .platform_data  = &power_pdata,
 573         },
 574 };
 575 
 576 static struct wm97xx_batt_pdata mioa701_battery_data = {
 577         .batt_aux       = WM97XX_AUX_ID1,
 578         .temp_aux       = -1,
 579         .charge_gpio    = -1,
 580         .min_voltage    = 0xc00,
 581         .max_voltage    = 0xfc0,
 582         .batt_tech      = POWER_SUPPLY_TECHNOLOGY_LION,
 583         .batt_div       = 1,
 584         .batt_mult      = 1,
 585         .batt_name      = "mioa701_battery",
 586 };
 587 
 588 static struct wm97xx_pdata mioa701_wm97xx_pdata = {
 589         .batt_pdata     = &mioa701_battery_data,
 590 };
 591 
 592 /*
 593  * Voltage regulation
 594  */
 595 static struct regulator_consumer_supply max1586_consumers[] = {
 596         REGULATOR_SUPPLY("vcc_core", NULL),
 597 };
 598 
 599 static struct regulator_init_data max1586_v3_info = {
 600         .constraints = {
 601                 .name = "vcc_core range",
 602                 .min_uV = 1000000,
 603                 .max_uV = 1705000,
 604                 .always_on = 1,
 605                 .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
 606         },
 607         .num_consumer_supplies = ARRAY_SIZE(max1586_consumers),
 608         .consumer_supplies = max1586_consumers,
 609 };
 610 
 611 static struct max1586_subdev_data max1586_subdevs[] = {
 612         { .name = "vcc_core", .id = MAX1586_V3,
 613           .platform_data = &max1586_v3_info },
 614 };
 615 
 616 static struct max1586_platform_data max1586_info = {
 617         .subdevs = max1586_subdevs,
 618         .num_subdevs = ARRAY_SIZE(max1586_subdevs),
 619         .v3_gain = MAX1586_GAIN_NO_R24, /* 700..1475 mV */
 620 };
 621 
 622 /*
 623  * Camera interface
 624  */
 625 struct pxacamera_platform_data mioa701_pxacamera_platform_data = {
 626         .flags  = PXA_CAMERA_MASTER | PXA_CAMERA_DATAWIDTH_8 |
 627                 PXA_CAMERA_PCLK_EN | PXA_CAMERA_MCLK_EN,
 628         .mclk_10khz = 5000,
 629         .sensor_i2c_adapter_id = 0,
 630         .sensor_i2c_address = 0x5d,
 631 };
 632 
 633 static struct i2c_board_info __initdata mioa701_pi2c_devices[] = {
 634         {
 635                 I2C_BOARD_INFO("max1586", 0x14),
 636                 .platform_data = &max1586_info,
 637         },
 638 };
 639 
 640 /* Board I2C devices. */
 641 static struct i2c_board_info mioa701_i2c_devices[] = {
 642         {
 643                 I2C_BOARD_INFO("mt9m111", 0x5d),
 644         },
 645 };
 646 
 647 struct i2c_pxa_platform_data i2c_pdata = {
 648         .fast_mode = 1,
 649 };
 650 
 651 static pxa2xx_audio_ops_t mioa701_ac97_info = {
 652         .reset_gpio = 95,
 653         .codec_pdata = { &mioa701_wm97xx_pdata, },
 654 };
 655 
 656 /*
 657  * Mio global
 658  */
 659 
 660 /* Devices */
 661 #define MIO_PARENT_DEV(var, strname, tparent, pdata)    \
 662 static struct platform_device var = {                   \
 663         .name           = strname,                      \
 664         .id             = -1,                           \
 665         .dev            = {                             \
 666                 .platform_data = pdata,                 \
 667                 .parent = tparent,                      \
 668         },                                              \
 669 };
 670 #define MIO_SIMPLE_DEV(var, strname, pdata)     \
 671         MIO_PARENT_DEV(var, strname, NULL, pdata)
 672 
 673 MIO_SIMPLE_DEV(mioa701_gpio_keys, "gpio-keys",      &mioa701_gpio_keys_data)
 674 MIO_PARENT_DEV(mioa701_backlight, "pwm-backlight",  &pxa27x_device_pwm0.dev,
 675                 &mioa701_backlight_data);
 676 MIO_SIMPLE_DEV(mioa701_led,       "leds-gpio",      &gpio_led_info)
 677 MIO_SIMPLE_DEV(pxa2xx_pcm,        "pxa2xx-pcm",     NULL)
 678 MIO_SIMPLE_DEV(mioa701_sound,     "mioa701-wm9713", NULL)
 679 MIO_SIMPLE_DEV(mioa701_board,     "mioa701-board",  NULL)
 680 MIO_SIMPLE_DEV(gpio_vbus,         "gpio-vbus",      &gpio_vbus_data);
 681 
 682 static struct platform_device *devices[] __initdata = {
 683         &mioa701_gpio_keys,
 684         &mioa701_backlight,
 685         &mioa701_led,
 686         &pxa2xx_pcm,
 687         &mioa701_sound,
 688         &power_dev,
 689         &docg3,
 690         &gpio_vbus,
 691         &mioa701_board,
 692 };
 693 
 694 static void mioa701_machine_exit(void);
 695 
 696 static void mioa701_poweroff(void)
 697 {
 698         mioa701_machine_exit();
 699         pxa_restart(REBOOT_SOFT, NULL);
 700 }
 701 
 702 static void mioa701_restart(enum reboot_mode c, const char *cmd)
 703 {
 704         mioa701_machine_exit();
 705         pxa_restart(REBOOT_SOFT, cmd);
 706 }
 707 
 708 static struct gpio global_gpios[] = {
 709         { GPIO9_CHARGE_EN, GPIOF_OUT_INIT_HIGH, "Charger enable" },
 710         { GPIO18_POWEROFF, GPIOF_OUT_INIT_LOW, "Power Off" },
 711         { GPIO87_LCD_POWER, GPIOF_OUT_INIT_LOW, "LCD Power" },
 712         { GPIO56_MT9M111_nOE, GPIOF_OUT_INIT_LOW, "Camera nOE" },
 713 };
 714 
 715 static struct regulator_consumer_supply fixed_5v0_consumers[] = {
 716         REGULATOR_SUPPLY("power", "pwm-backlight"),
 717 };
 718 
 719 static void __init mioa701_machine_init(void)
 720 {
 721         int rc;
 722 
 723         PSLR  = 0xff100000; /* SYSDEL=125ms, PWRDEL=125ms, PSLR_SL_ROD=1 */
 724         PCFR = PCFR_DC_EN | PCFR_GPR_EN | PCFR_OPDE;
 725         RTTR = 32768 - 1; /* Reset crazy WinCE value */
 726         UP2OCR = UP2OCR_HXOE;
 727 
 728         /*
 729          * Set up the flash memory : DiskOnChip G3 on first static memory bank
 730          */
 731         __raw_writel(0x7ff02dd8, MSC0);
 732         __raw_writel(0x0001c391, MCMEM0);
 733         __raw_writel(0x0001c391, MCATT0);
 734         __raw_writel(0x0001c391, MCIO0);
 735 
 736 
 737         pxa2xx_mfp_config(ARRAY_AND_SIZE(mioa701_pin_config));
 738         pxa_set_ffuart_info(NULL);
 739         pxa_set_btuart_info(NULL);
 740         pxa_set_stuart_info(NULL);
 741         rc = gpio_request_array(ARRAY_AND_SIZE(global_gpios));
 742         if (rc)
 743                 pr_err("MioA701: Failed to request GPIOs: %d", rc);
 744         bootstrap_init();
 745         pxa_set_fb_info(NULL, &mioa701_pxafb_info);
 746         gpiod_add_lookup_table(&mioa701_mci_gpio_table);
 747         pxa_set_mci_info(&mioa701_mci_info);
 748         pxa_set_keypad_info(&mioa701_keypad_info);
 749         pxa_set_udc_info(&mioa701_udc_info);
 750         pxa_set_ac97_info(&mioa701_ac97_info);
 751         pm_power_off = mioa701_poweroff;
 752         pwm_add_table(mioa701_pwm_lookup, ARRAY_SIZE(mioa701_pwm_lookup));
 753         platform_add_devices(devices, ARRAY_SIZE(devices));
 754         gsm_init();
 755 
 756         i2c_register_board_info(0, ARRAY_AND_SIZE(mioa701_i2c_devices));
 757         i2c_register_board_info(1, ARRAY_AND_SIZE(mioa701_pi2c_devices));
 758         pxa_set_i2c_info(&i2c_pdata);
 759         pxa27x_set_i2c_power_info(NULL);
 760         pxa_set_camera_info(&mioa701_pxacamera_platform_data);
 761 
 762         regulator_register_always_on(0, "fixed-5.0V", fixed_5v0_consumers,
 763                                      ARRAY_SIZE(fixed_5v0_consumers),
 764                                      5000000);
 765         regulator_has_full_constraints();
 766 }
 767 
 768 static void mioa701_machine_exit(void)
 769 {
 770         bootstrap_exit();
 771         gsm_exit();
 772 }
 773 
 774 MACHINE_START(MIOA701, "MIO A701")
 775         .atag_offset    = 0x100,
 776         .map_io         = &pxa27x_map_io,
 777         .nr_irqs        = PXA_NR_IRQS,
 778         .init_irq       = &pxa27x_init_irq,
 779         .handle_irq     = &pxa27x_handle_irq,
 780         .init_machine   = mioa701_machine_init,
 781         .init_time      = pxa_timer_init,
 782         .restart        = mioa701_restart,
 783 MACHINE_END

/* [<][>][^][v][top][bottom][index][help] */