1config SND_BF5XX_I2S
2	tristate "SoC I2S Audio for the ADI Blackfin chip"
3	depends on BLACKFIN
4	select SND_BF5XX_SOC_SPORT if !BF60x
5	select SND_BF6XX_SOC_SPORT if BF60x
6	help
7	  Say Y or M if you want to add support for codecs attached to
8	  the Blackfin SPORT (synchronous serial ports) interface in I2S
9	  mode (supports single stereo In/Out).
10	  You will also need to select the audio interfaces to support below.
11
12config SND_BF5XX_SOC_SSM2602
13	tristate "SoC SSM2602 Audio Codec Add-On Card support"
14	depends on SND_BF5XX_I2S && SND_SOC_I2C_AND_SPI
15	select SND_BF5XX_SOC_I2S if !BF60x
16	select SND_BF6XX_SOC_I2S if BF60x
17	select SND_SOC_SSM2602_SPI if SPI_MASTER
18	select SND_SOC_SSM2602_I2C if I2C
19	help
20	  Say Y if you want to add support for the Analog Devices
21	  SSM2602 Audio Codec Add-On Card.
22
23config SND_SOC_BFIN_EVAL_ADAU1701
24	tristate "Support for the EVAL-ADAU1701MINIZ board on Blackfin eval boards"
25	depends on SND_BF5XX_I2S && I2C
26	select SND_BF5XX_SOC_I2S
27	select SND_SOC_ADAU1701
28	help
29	  Say Y if you want to add support for the Analog Devices EVAL-ADAU1701MINIZ
30	  board connected to one of the Blackfin evaluation boards like the
31	  BF5XX-STAMP or BF5XX-EZKIT.
32
33config SND_SOC_BFIN_EVAL_ADAU1373
34	tristate "Support for the EVAL-ADAU1373 board on Blackfin eval boards"
35	depends on SND_BF5XX_I2S && I2C
36	select SND_BF5XX_SOC_I2S
37	select SND_SOC_ADAU1373
38	help
39	  Say Y if you want to add support for the Analog Devices EVAL-ADAU1373
40	  board connected to one of the Blackfin evaluation boards like the
41	  BF5XX-STAMP or BF5XX-EZKIT.
42
43	  Note: This driver assumes that first ADAU1373 DAI is connected to the
44	  first SPORT port on the BF5XX board.
45
46config SND_SOC_BFIN_EVAL_ADAU1X61
47	tristate "Support for the EVAL-ADAU1X61 board on Blackfin eval boards"
48	depends on SND_BF5XX_I2S && I2C
49	select SND_BF5XX_SOC_I2S
50	select SND_SOC_ADAU1761_I2C
51	help
52	  Say Y if you want to add support for the Analog Devices EVAL-ADAU1X61
53	  board connected to one of the Blackfin evaluation boards like the
54	  BF5XX-STAMP or BF5XX-EZKIT.
55
56	  Note: This driver assumes that the ADAU1X61 is connected to the
57	  first SPORT port on the BF5XX board.
58
59config SND_SOC_BFIN_EVAL_ADAU1X81
60	tristate "Support for the EVAL-ADAU1X81 boards on Blackfin eval boards"
61	depends on SND_BF5XX_I2S && I2C
62	select SND_BF5XX_SOC_I2S
63	select SND_SOC_ADAU1781_I2C
64	help
65	  Say Y if you want to add support for the Analog Devices EVAL-ADAU1X81
66	  board connected to one of the Blackfin evaluation boards like the
67	  BF5XX-STAMP or BF5XX-EZKIT.
68
69	  Note: This driver assumes that the ADAU1X81 is connected to the
70	  first SPORT port on the BF5XX board.
71
72config SND_SOC_BFIN_EVAL_ADAV80X
73	tristate "Support for the EVAL-ADAV80X boards on Blackfin eval boards"
74	depends on SND_BF5XX_I2S && SND_SOC_I2C_AND_SPI
75	select SND_BF5XX_SOC_I2S
76	select SND_SOC_ADAV801 if SPI_MASTER
77	select SND_SOC_ADAV803 if I2C
78	help
79	  Say Y if you want to add support for the Analog Devices EVAL-ADAV801 or
80	  EVAL-ADAV803 board connected to one of the Blackfin evaluation boards
81	  like the BF5XX-STAMP or BF5XX-EZKIT.
82
83	  Note: This driver assumes that the ADAV80X digital record and playback
84	  interfaces are connected to the first SPORT port on the BF5XX board.
85
86config SND_BF5XX_SOC_AD1836
87	tristate "SoC AD1836 Audio support for BF5xx"
88	depends on SND_BF5XX_I2S && SPI_MASTER
89	select SND_BF5XX_SOC_I2S
90	select SND_SOC_AD1836
91	help
92	  Say Y if you want to add support for SoC audio on BF5xx STAMP/EZKIT.
93
94config SND_BF5XX_SOC_AD193X
95	tristate "SoC AD193X Audio support for Blackfin"
96	depends on SND_BF5XX_I2S && SND_SOC_I2C_AND_SPI
97	select SND_BF5XX_SOC_I2S
98	select SND_SOC_AD193X_I2C if I2C
99	select SND_SOC_AD193X_SPI if SPI_MASTER
100	help
101	  Say Y if you want to add support for AD193X codec on Blackfin.
102	  This driver supports AD1936, AD1937, AD1938 and AD1939.
103
104config SND_BF5XX_SOC_AD73311
105	tristate "SoC AD73311 Audio support for Blackfin"
106	depends on SND_BF5XX_I2S
107	select SND_BF5XX_SOC_I2S
108	select SND_SOC_AD73311
109	help
110	  Say Y if you want to add support for AD73311 codec on Blackfin.
111
112config SND_BFIN_AD73311_SE
113	int "PF pin for AD73311L Chip Select"
114	depends on SND_BF5XX_SOC_AD73311
115	default 4
116	help
117	  Enter the GPIO used to control AD73311's SE pin. Acceptable
118	  values are 0 to 7
119
120config SND_BF5XX_AC97
121	tristate "SoC AC97 Audio for the ADI BF5xx chip"
122	depends on BLACKFIN
123	select AC97_BUS
124	select SND_SOC_AC97_BUS
125	select SND_BF5XX_SOC_SPORT
126	select SND_BF5XX_SOC_AC97
127	help
128	  Say Y or M if you want to add support for codecs attached to
129	  the Blackfin SPORT (synchronous serial ports) interface in slot 16
130	  mode (pseudo AC97 interface).
131	  You will also need to select the audio interfaces to support below.
132
133	  Note:
134	  AC97 codecs which do not implement the slot-16 mode will not function
135	  properly with this driver. This driver is known to work with the
136	  Analog Devices line of AC97 codecs.
137
138config SND_BF5XX_MMAP_SUPPORT
139	bool "Enable MMAP Support"
140	depends on SND_BF5XX_AC97
141	default y
142	help
143	  Say y if you want AC97 driver to support mmap mode.
144	  We introduce an intermediate buffer to simulate mmap.
145
146config SND_BF5XX_MULTICHAN_SUPPORT
147	bool "Enable Multichannel Support"
148	depends on SND_BF5XX_AC97
149	default n
150	help
151	  Say y if you want AC97 driver to support up to 5.1 channel audio.
152	  this mode will consume much more memory for DMA.
153
154config SND_BF5XX_HAVE_COLD_RESET
155	bool "BOARD has COLD Reset GPIO"
156	depends on SND_BF5XX_AC97
157	default y if BFIN548_EZKIT
158	default n if !BFIN548_EZKIT
159
160config SND_BF5XX_RESET_GPIO_NUM
161	int "Set a GPIO for cold reset"
162	depends on SND_BF5XX_HAVE_COLD_RESET
163	range 0 159
164	default 19 if BFIN548_EZKIT
165	default 5 if BFIN537_STAMP
166	default 0
167	help
168	  Set the correct GPIO for RESET the sound chip.
169
170config SND_BF5XX_SOC_AD1980
171	tristate "SoC AD1980/1 Audio support for BF5xx (Obsolete)"
172	depends on SND_BF5XX_AC97
173	select SND_BF5XX_SOC_AC97
174	select SND_SOC_AD1980
175	help
176	  Say Y if you want to add support for SoC audio on BF5xx STAMP/EZKIT.
177
178	  Warning:
179	  Because Analog Devices Inc. discontinued the ad1980 sound chip since
180	  Sep. 2009, this ad1980 driver is not maintained, tested and supported
181	  by ADI now.
182
183config SND_BF5XX_SOC_SPORT
184	tristate
185
186config SND_BF6XX_SOC_SPORT
187	tristate
188
189config SND_BF5XX_SOC_I2S
190	tristate
191
192config SND_BF6XX_SOC_I2S
193	tristate
194
195config SND_BF5XX_SOC_AC97
196	tristate
197
198config SND_BF5XX_SPORT_NUM
199	int "Set a SPORT for Sound chip"
200	depends on (SND_BF5XX_SOC_SPORT || SND_BF6XX_SOC_SPORT)
201	range 0 3 if BF54x
202	range 0 1 if !BF54x
203	default 0
204	help
205	  Set the correct SPORT for sound chip.
206