1#ifndef LINUX_B43_PHY_COMMON_H_ 2#define LINUX_B43_PHY_COMMON_H_ 3 4#include <linux/types.h> 5#include <linux/nl80211.h> 6 7struct b43_wldev; 8 9/* Complex number using 2 32-bit signed integers */ 10struct b43_c32 { s32 i, q; }; 11 12#define CORDIC_CONVERT(value) (((value) >= 0) ? \ 13 ((((value) >> 15) + 1) >> 1) : \ 14 -((((-(value)) >> 15) + 1) >> 1)) 15 16/* PHY register routing bits */ 17#define B43_PHYROUTE 0x0C00 /* PHY register routing bits mask */ 18#define B43_PHYROUTE_BASE 0x0000 /* Base registers */ 19#define B43_PHYROUTE_OFDM_GPHY 0x0400 /* OFDM register routing for G-PHYs */ 20#define B43_PHYROUTE_EXT_GPHY 0x0800 /* Extended G-PHY registers */ 21#define B43_PHYROUTE_N_BMODE 0x0C00 /* N-PHY BMODE registers */ 22 23/* CCK (B-PHY) registers. */ 24#define B43_PHY_CCK(reg) ((reg) | B43_PHYROUTE_BASE) 25/* N-PHY registers. */ 26#define B43_PHY_N(reg) ((reg) | B43_PHYROUTE_BASE) 27/* N-PHY BMODE registers. */ 28#define B43_PHY_N_BMODE(reg) ((reg) | B43_PHYROUTE_N_BMODE) 29/* OFDM (A-PHY) registers. */ 30#define B43_PHY_OFDM(reg) ((reg) | B43_PHYROUTE_OFDM_GPHY) 31/* Extended G-PHY registers. */ 32#define B43_PHY_EXTG(reg) ((reg) | B43_PHYROUTE_EXT_GPHY) 33 34 35/* Masks for the PHY versioning registers. */ 36#define B43_PHYVER_ANALOG 0xF000 37#define B43_PHYVER_ANALOG_SHIFT 12 38#define B43_PHYVER_TYPE 0x0F00 39#define B43_PHYVER_TYPE_SHIFT 8 40#define B43_PHYVER_VERSION 0x00FF 41 42/* PHY writes need to be flushed if we reach limit */ 43#define B43_MAX_WRITES_IN_ROW 24 44 45/** 46 * enum b43_interference_mitigation - Interference Mitigation mode 47 * 48 * @B43_INTERFMODE_NONE: Disabled 49 * @B43_INTERFMODE_NONWLAN: Non-WLAN Interference Mitigation 50 * @B43_INTERFMODE_MANUALWLAN: WLAN Interference Mitigation 51 * @B43_INTERFMODE_AUTOWLAN: Automatic WLAN Interference Mitigation 52 */ 53enum b43_interference_mitigation { 54 B43_INTERFMODE_NONE, 55 B43_INTERFMODE_NONWLAN, 56 B43_INTERFMODE_MANUALWLAN, 57 B43_INTERFMODE_AUTOWLAN, 58}; 59 60/* Antenna identifiers */ 61enum { 62 B43_ANTENNA0 = 0, /* Antenna 0 */ 63 B43_ANTENNA1 = 1, /* Antenna 1 */ 64 B43_ANTENNA_AUTO0 = 2, /* Automatic, starting with antenna 0 */ 65 B43_ANTENNA_AUTO1 = 3, /* Automatic, starting with antenna 1 */ 66 B43_ANTENNA2 = 4, 67 B43_ANTENNA3 = 8, 68 69 B43_ANTENNA_AUTO = B43_ANTENNA_AUTO0, 70 B43_ANTENNA_DEFAULT = B43_ANTENNA_AUTO, 71}; 72 73/** 74 * enum b43_txpwr_result - Return value for the recalc_txpower PHY op. 75 * 76 * @B43_TXPWR_RES_NEED_ADJUST: Values changed. Hardware adjustment is needed. 77 * @B43_TXPWR_RES_DONE: No more work to do. Everything is done. 78 */ 79enum b43_txpwr_result { 80 B43_TXPWR_RES_NEED_ADJUST, 81 B43_TXPWR_RES_DONE, 82}; 83 84/** 85 * struct b43_phy_operations - Function pointers for PHY ops. 86 * 87 * @allocate: Allocate and initialise the PHY data structures. 88 * Must not be NULL. 89 * @free: Destroy and free the PHY data structures. 90 * Must not be NULL. 91 * 92 * @prepare_structs: Prepare the PHY data structures. 93 * The data structures allocated in @allocate are 94 * initialized here. 95 * Must not be NULL. 96 * @prepare_hardware: Prepare the PHY. This is called before b43_chip_init to 97 * do some early early PHY hardware init. 98 * Can be NULL, if not required. 99 * @init: Initialize the PHY. 100 * Must not be NULL. 101 * @exit: Shutdown the PHY. 102 * Can be NULL, if not required. 103 * 104 * @phy_read: Read from a PHY register. 105 * Must not be NULL. 106 * @phy_write: Write to a PHY register. 107 * Must not be NULL. 108 * @phy_maskset: Maskset a PHY register, taking shortcuts. 109 * If it is NULL, a generic algorithm is used. 110 * @radio_read: Read from a Radio register. 111 * Must not be NULL. 112 * @radio_write: Write to a Radio register. 113 * Must not be NULL. 114 * 115 * @supports_hwpctl: Returns a boolean whether Hardware Power Control 116 * is supported or not. 117 * If NULL, hwpctl is assumed to be never supported. 118 * @software_rfkill: Turn the radio ON or OFF. 119 * Possible state values are 120 * RFKILL_STATE_SOFT_BLOCKED or 121 * RFKILL_STATE_UNBLOCKED 122 * Must not be NULL. 123 * @switch_analog: Turn the Analog on/off. 124 * Must not be NULL. 125 * @switch_channel: Switch the radio to another channel. 126 * Must not be NULL. 127 * @get_default_chan: Just returns the default channel number. 128 * Must not be NULL. 129 * @set_rx_antenna: Set the antenna used for RX. 130 * Can be NULL, if not supported. 131 * @interf_mitigation: Switch the Interference Mitigation mode. 132 * Can be NULL, if not supported. 133 * 134 * @recalc_txpower: Recalculate the transmission power parameters. 135 * This callback has to recalculate the TX power settings, 136 * but does not need to write them to the hardware, yet. 137 * Returns enum b43_txpwr_result to indicate whether the hardware 138 * needs to be adjusted. 139 * If B43_TXPWR_NEED_ADJUST is returned, @adjust_txpower 140 * will be called later. 141 * If the parameter "ignore_tssi" is true, the TSSI values should 142 * be ignored and a recalculation of the power settings should be 143 * done even if the TSSI values did not change. 144 * This function may sleep, but should not. 145 * Must not be NULL. 146 * @adjust_txpower: Write the previously calculated TX power settings 147 * (from @recalc_txpower) to the hardware. 148 * This function may sleep. 149 * Can be NULL, if (and ONLY if) @recalc_txpower _always_ 150 * returns B43_TXPWR_RES_DONE. 151 * 152 * @pwork_15sec: Periodic work. Called every 15 seconds. 153 * Can be NULL, if not required. 154 * @pwork_60sec: Periodic work. Called every 60 seconds. 155 * Can be NULL, if not required. 156 */ 157struct b43_phy_operations { 158 /* Initialisation */ 159 int (*allocate)(struct b43_wldev *dev); 160 void (*free)(struct b43_wldev *dev); 161 void (*prepare_structs)(struct b43_wldev *dev); 162 int (*prepare_hardware)(struct b43_wldev *dev); 163 int (*init)(struct b43_wldev *dev); 164 void (*exit)(struct b43_wldev *dev); 165 166 /* Register access */ 167 u16 (*phy_read)(struct b43_wldev *dev, u16 reg); 168 void (*phy_write)(struct b43_wldev *dev, u16 reg, u16 value); 169 void (*phy_maskset)(struct b43_wldev *dev, u16 reg, u16 mask, u16 set); 170 u16 (*radio_read)(struct b43_wldev *dev, u16 reg); 171 void (*radio_write)(struct b43_wldev *dev, u16 reg, u16 value); 172 173 /* Radio */ 174 bool (*supports_hwpctl)(struct b43_wldev *dev); 175 void (*software_rfkill)(struct b43_wldev *dev, bool blocked); 176 void (*switch_analog)(struct b43_wldev *dev, bool on); 177 int (*switch_channel)(struct b43_wldev *dev, unsigned int new_channel); 178 unsigned int (*get_default_chan)(struct b43_wldev *dev); 179 void (*set_rx_antenna)(struct b43_wldev *dev, int antenna); 180 int (*interf_mitigation)(struct b43_wldev *dev, 181 enum b43_interference_mitigation new_mode); 182 183 /* Transmission power adjustment */ 184 enum b43_txpwr_result (*recalc_txpower)(struct b43_wldev *dev, 185 bool ignore_tssi); 186 void (*adjust_txpower)(struct b43_wldev *dev); 187 188 /* Misc */ 189 void (*pwork_15sec)(struct b43_wldev *dev); 190 void (*pwork_60sec)(struct b43_wldev *dev); 191}; 192 193struct b43_phy_a; 194struct b43_phy_g; 195struct b43_phy_n; 196struct b43_phy_lp; 197struct b43_phy_ht; 198struct b43_phy_lcn; 199 200struct b43_phy { 201 /* Hardware operation callbacks. */ 202 const struct b43_phy_operations *ops; 203 204 /* Most hardware context information is stored in the standard- 205 * specific data structures pointed to by the pointers below. 206 * Only one of them is valid (the currently enabled PHY). */ 207#ifdef CONFIG_B43_DEBUG 208 /* No union for debug build to force NULL derefs in buggy code. */ 209 struct { 210#else 211 union { 212#endif 213 /* A-PHY specific information */ 214 struct b43_phy_a *a; 215 /* G-PHY specific information */ 216 struct b43_phy_g *g; 217 /* N-PHY specific information */ 218 struct b43_phy_n *n; 219 /* LP-PHY specific information */ 220 struct b43_phy_lp *lp; 221 /* HT-PHY specific information */ 222 struct b43_phy_ht *ht; 223 /* LCN-PHY specific information */ 224 struct b43_phy_lcn *lcn; 225 /* AC-PHY specific information */ 226 struct b43_phy_ac *ac; 227 }; 228 229 /* Band support flags. */ 230 bool supports_2ghz; 231 bool supports_5ghz; 232 233 /* Is GMODE (2 GHz mode) bit enabled? */ 234 bool gmode; 235 236 /* After power reset full init has to be performed */ 237 bool do_full_init; 238 239 /* Analog Type */ 240 u8 analog; 241 /* B43_PHYTYPE_ */ 242 u8 type; 243 /* PHY revision number. */ 244 u8 rev; 245 246 /* Count writes since last read */ 247 u8 writes_counter; 248 249 /* Radio versioning */ 250 u16 radio_manuf; /* Radio manufacturer */ 251 u16 radio_ver; /* Radio version */ 252 u8 radio_rev; /* Radio revision */ 253 254 /* Software state of the radio */ 255 bool radio_on; 256 257 /* Desired TX power level (in dBm). 258 * This is set by the user and adjusted in b43_phy_xmitpower(). */ 259 int desired_txpower; 260 261 /* Hardware Power Control enabled? */ 262 bool hardware_power_control; 263 264 /* The time (in absolute jiffies) when the next TX power output 265 * check is needed. */ 266 unsigned long next_txpwr_check_time; 267 268 /* Current channel */ 269 struct cfg80211_chan_def *chandef; 270 unsigned int channel; 271 272 /* PHY TX errors counter. */ 273 atomic_t txerr_cnt; 274 275#ifdef CONFIG_B43_DEBUG 276 /* PHY registers locked (w.r.t. firmware) */ 277 bool phy_locked; 278 /* Radio registers locked (w.r.t. firmware) */ 279 bool radio_locked; 280#endif /* B43_DEBUG */ 281}; 282 283 284/** 285 * b43_phy_allocate - Allocate PHY structs 286 * Allocate the PHY data structures, based on the current dev->phy.type 287 */ 288int b43_phy_allocate(struct b43_wldev *dev); 289 290/** 291 * b43_phy_free - Free PHY structs 292 */ 293void b43_phy_free(struct b43_wldev *dev); 294 295/** 296 * b43_phy_init - Initialise the PHY 297 */ 298int b43_phy_init(struct b43_wldev *dev); 299 300/** 301 * b43_phy_exit - Cleanup PHY 302 */ 303void b43_phy_exit(struct b43_wldev *dev); 304 305/** 306 * b43_has_hardware_pctl - Hardware Power Control supported? 307 * Returns a boolean, whether hardware power control is supported. 308 */ 309bool b43_has_hardware_pctl(struct b43_wldev *dev); 310 311/** 312 * b43_phy_read - 16bit PHY register read access 313 */ 314u16 b43_phy_read(struct b43_wldev *dev, u16 reg); 315 316/** 317 * b43_phy_write - 16bit PHY register write access 318 */ 319void b43_phy_write(struct b43_wldev *dev, u16 reg, u16 value); 320 321/** 322 * b43_phy_copy - copy contents of 16bit PHY register to another 323 */ 324void b43_phy_copy(struct b43_wldev *dev, u16 destreg, u16 srcreg); 325 326/** 327 * b43_phy_mask - Mask a PHY register with a mask 328 */ 329void b43_phy_mask(struct b43_wldev *dev, u16 offset, u16 mask); 330 331/** 332 * b43_phy_set - OR a PHY register with a bitmap 333 */ 334void b43_phy_set(struct b43_wldev *dev, u16 offset, u16 set); 335 336/** 337 * b43_phy_maskset - Mask and OR a PHY register with a mask and bitmap 338 */ 339void b43_phy_maskset(struct b43_wldev *dev, u16 offset, u16 mask, u16 set); 340 341/** 342 * b43_radio_read - 16bit Radio register read access 343 */ 344u16 b43_radio_read(struct b43_wldev *dev, u16 reg); 345#define b43_radio_read16 b43_radio_read /* DEPRECATED */ 346 347/** 348 * b43_radio_write - 16bit Radio register write access 349 */ 350void b43_radio_write(struct b43_wldev *dev, u16 reg, u16 value); 351#define b43_radio_write16 b43_radio_write /* DEPRECATED */ 352 353/** 354 * b43_radio_mask - Mask a 16bit radio register with a mask 355 */ 356void b43_radio_mask(struct b43_wldev *dev, u16 offset, u16 mask); 357 358/** 359 * b43_radio_set - OR a 16bit radio register with a bitmap 360 */ 361void b43_radio_set(struct b43_wldev *dev, u16 offset, u16 set); 362 363/** 364 * b43_radio_maskset - Mask and OR a radio register with a mask and bitmap 365 */ 366void b43_radio_maskset(struct b43_wldev *dev, u16 offset, u16 mask, u16 set); 367 368/** 369 * b43_radio_wait_value - Waits for a given value in masked register read 370 */ 371bool b43_radio_wait_value(struct b43_wldev *dev, u16 offset, u16 mask, 372 u16 value, int delay, int timeout); 373 374/** 375 * b43_radio_lock - Lock firmware radio register access 376 */ 377void b43_radio_lock(struct b43_wldev *dev); 378 379/** 380 * b43_radio_unlock - Unlock firmware radio register access 381 */ 382void b43_radio_unlock(struct b43_wldev *dev); 383 384/** 385 * b43_phy_lock - Lock firmware PHY register access 386 */ 387void b43_phy_lock(struct b43_wldev *dev); 388 389/** 390 * b43_phy_unlock - Unlock firmware PHY register access 391 */ 392void b43_phy_unlock(struct b43_wldev *dev); 393 394void b43_phy_put_into_reset(struct b43_wldev *dev); 395void b43_phy_take_out_of_reset(struct b43_wldev *dev); 396 397/** 398 * b43_switch_channel - Switch to another channel 399 */ 400int b43_switch_channel(struct b43_wldev *dev, unsigned int new_channel); 401 402/** 403 * b43_software_rfkill - Turn the radio ON or OFF in software. 404 */ 405void b43_software_rfkill(struct b43_wldev *dev, bool blocked); 406 407/** 408 * b43_phy_txpower_check - Check TX power output. 409 * 410 * Compare the current TX power output to the desired power emission 411 * and schedule an adjustment in case it mismatches. 412 * 413 * @flags: OR'ed enum b43_phy_txpower_check_flags flags. 414 * See the docs below. 415 */ 416void b43_phy_txpower_check(struct b43_wldev *dev, unsigned int flags); 417/** 418 * enum b43_phy_txpower_check_flags - Flags for b43_phy_txpower_check() 419 * 420 * @B43_TXPWR_IGNORE_TIME: Ignore the schedule time and force-redo 421 * the check now. 422 * @B43_TXPWR_IGNORE_TSSI: Redo the recalculation, even if the average 423 * TSSI did not change. 424 */ 425enum b43_phy_txpower_check_flags { 426 B43_TXPWR_IGNORE_TIME = (1 << 0), 427 B43_TXPWR_IGNORE_TSSI = (1 << 1), 428}; 429 430struct work_struct; 431void b43_phy_txpower_adjust_work(struct work_struct *work); 432 433/** 434 * b43_phy_shm_tssi_read - Read the average of the last 4 TSSI from SHM. 435 * 436 * @shm_offset: The SHM address to read the values from. 437 * 438 * Returns the average of the 4 TSSI values, or a negative error code. 439 */ 440int b43_phy_shm_tssi_read(struct b43_wldev *dev, u16 shm_offset); 441 442/** 443 * b43_phy_switch_analog_generic - Generic PHY operation for switching the Analog. 444 * 445 * It does the switching based on the PHY0 core register. 446 * Do _not_ call this directly. Only use it as a switch_analog callback 447 * for struct b43_phy_operations. 448 */ 449void b43_phyop_switch_analog_generic(struct b43_wldev *dev, bool on); 450 451bool b43_is_40mhz(struct b43_wldev *dev); 452 453void b43_phy_force_clock(struct b43_wldev *dev, bool force); 454 455struct b43_c32 b43_cordic(int theta); 456 457#endif /* LINUX_B43_PHY_COMMON_H_ */ 458