1/*
2 * Driver for ICPlus PHYs
3 *
4 * Copyright (c) 2007 Freescale Semiconductor, Inc.
5 *
6 * This program is free software; you can redistribute  it and/or modify it
7 * under  the terms of  the GNU General  Public License as published by the
8 * Free Software Foundation;  either version 2 of the  License, or (at your
9 * option) any later version.
10 *
11 */
12#include <linux/kernel.h>
13#include <linux/string.h>
14#include <linux/errno.h>
15#include <linux/unistd.h>
16#include <linux/interrupt.h>
17#include <linux/init.h>
18#include <linux/delay.h>
19#include <linux/netdevice.h>
20#include <linux/etherdevice.h>
21#include <linux/skbuff.h>
22#include <linux/spinlock.h>
23#include <linux/mm.h>
24#include <linux/module.h>
25#include <linux/mii.h>
26#include <linux/ethtool.h>
27#include <linux/phy.h>
28
29#include <asm/io.h>
30#include <asm/irq.h>
31#include <asm/uaccess.h>
32
33MODULE_DESCRIPTION("ICPlus IP175C/IP101A/IP101G/IC1001 PHY drivers");
34MODULE_AUTHOR("Michael Barkowski");
35MODULE_LICENSE("GPL");
36
37/* IP101A/G - IP1001 */
38#define IP10XX_SPEC_CTRL_STATUS		16	/* Spec. Control Register */
39#define IP1001_RXPHASE_SEL		(1<<0)	/* Add delay on RX_CLK */
40#define IP1001_TXPHASE_SEL		(1<<1)	/* Add delay on TX_CLK */
41#define IP1001_SPEC_CTRL_STATUS_2	20	/* IP1001 Spec. Control Reg 2 */
42#define IP1001_APS_ON			11	/* IP1001 APS Mode  bit */
43#define IP101A_G_APS_ON			2	/* IP101A/G APS Mode bit */
44#define IP101A_G_IRQ_CONF_STATUS	0x11	/* Conf Info IRQ & Status Reg */
45#define	IP101A_G_IRQ_PIN_USED		(1<<15) /* INTR pin used */
46#define	IP101A_G_IRQ_DEFAULT		IP101A_G_IRQ_PIN_USED
47
48static int ip175c_config_init(struct phy_device *phydev)
49{
50	int err, i;
51	static int full_reset_performed;
52
53	if (full_reset_performed == 0) {
54
55		/* master reset */
56		err = mdiobus_write(phydev->bus, 30, 0, 0x175c);
57		if (err < 0)
58			return err;
59
60		/* ensure no bus delays overlap reset period */
61		err = mdiobus_read(phydev->bus, 30, 0);
62
63		/* data sheet specifies reset period is 2 msec */
64		mdelay(2);
65
66		/* enable IP175C mode */
67		err = mdiobus_write(phydev->bus, 29, 31, 0x175c);
68		if (err < 0)
69			return err;
70
71		/* Set MII0 speed and duplex (in PHY mode) */
72		err = mdiobus_write(phydev->bus, 29, 22, 0x420);
73		if (err < 0)
74			return err;
75
76		/* reset switch ports */
77		for (i = 0; i < 5; i++) {
78			err = mdiobus_write(phydev->bus, i,
79					    MII_BMCR, BMCR_RESET);
80			if (err < 0)
81				return err;
82		}
83
84		for (i = 0; i < 5; i++)
85			err = mdiobus_read(phydev->bus, i, MII_BMCR);
86
87		mdelay(2);
88
89		full_reset_performed = 1;
90	}
91
92	if (phydev->addr != 4) {
93		phydev->state = PHY_RUNNING;
94		phydev->speed = SPEED_100;
95		phydev->duplex = DUPLEX_FULL;
96		phydev->link = 1;
97		netif_carrier_on(phydev->attached_dev);
98	}
99
100	return 0;
101}
102
103static int ip1xx_reset(struct phy_device *phydev)
104{
105	int bmcr;
106
107	/* Software Reset PHY */
108	bmcr = phy_read(phydev, MII_BMCR);
109	if (bmcr < 0)
110		return bmcr;
111	bmcr |= BMCR_RESET;
112	bmcr = phy_write(phydev, MII_BMCR, bmcr);
113	if (bmcr < 0)
114		return bmcr;
115
116	do {
117		bmcr = phy_read(phydev, MII_BMCR);
118		if (bmcr < 0)
119			return bmcr;
120	} while (bmcr & BMCR_RESET);
121
122	return 0;
123}
124
125static int ip1001_config_init(struct phy_device *phydev)
126{
127	int c;
128
129	c = ip1xx_reset(phydev);
130	if (c < 0)
131		return c;
132
133	/* Enable Auto Power Saving mode */
134	c = phy_read(phydev, IP1001_SPEC_CTRL_STATUS_2);
135	if (c < 0)
136		return c;
137	c |= IP1001_APS_ON;
138	c = phy_write(phydev, IP1001_SPEC_CTRL_STATUS_2, c);
139	if (c < 0)
140		return c;
141
142	if ((phydev->interface == PHY_INTERFACE_MODE_RGMII) ||
143	    (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) ||
144	    (phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID) ||
145	    (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID)) {
146
147		c = phy_read(phydev, IP10XX_SPEC_CTRL_STATUS);
148		if (c < 0)
149			return c;
150
151		c &= ~(IP1001_RXPHASE_SEL | IP1001_TXPHASE_SEL);
152
153		if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID)
154			c |= (IP1001_RXPHASE_SEL | IP1001_TXPHASE_SEL);
155		else if (phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID)
156			c |= IP1001_RXPHASE_SEL;
157		else if (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID)
158			c |= IP1001_TXPHASE_SEL;
159
160		c = phy_write(phydev, IP10XX_SPEC_CTRL_STATUS, c);
161		if (c < 0)
162			return c;
163	}
164
165	return 0;
166}
167
168static int ip101a_g_config_init(struct phy_device *phydev)
169{
170	int c;
171
172	c = ip1xx_reset(phydev);
173	if (c < 0)
174		return c;
175
176	/* INTR pin used: speed/link/duplex will cause an interrupt */
177	c = phy_write(phydev, IP101A_G_IRQ_CONF_STATUS, IP101A_G_IRQ_DEFAULT);
178	if (c < 0)
179		return c;
180
181	/* Enable Auto Power Saving mode */
182	c = phy_read(phydev, IP10XX_SPEC_CTRL_STATUS);
183	c |= IP101A_G_APS_ON;
184
185	return phy_write(phydev, IP10XX_SPEC_CTRL_STATUS, c);
186}
187
188static int ip175c_read_status(struct phy_device *phydev)
189{
190	if (phydev->addr == 4) /* WAN port */
191		genphy_read_status(phydev);
192	else
193		/* Don't need to read status for switch ports */
194		phydev->irq = PHY_IGNORE_INTERRUPT;
195
196	return 0;
197}
198
199static int ip175c_config_aneg(struct phy_device *phydev)
200{
201	if (phydev->addr == 4) /* WAN port */
202		genphy_config_aneg(phydev);
203
204	return 0;
205}
206
207static int ip101a_g_ack_interrupt(struct phy_device *phydev)
208{
209	int err = phy_read(phydev, IP101A_G_IRQ_CONF_STATUS);
210	if (err < 0)
211		return err;
212
213	return 0;
214}
215
216static struct phy_driver icplus_driver[] = {
217{
218	.phy_id		= 0x02430d80,
219	.name		= "ICPlus IP175C",
220	.phy_id_mask	= 0x0ffffff0,
221	.features	= PHY_BASIC_FEATURES,
222	.config_init	= &ip175c_config_init,
223	.config_aneg	= &ip175c_config_aneg,
224	.read_status	= &ip175c_read_status,
225	.suspend	= genphy_suspend,
226	.resume		= genphy_resume,
227	.driver		= { .owner = THIS_MODULE,},
228}, {
229	.phy_id		= 0x02430d90,
230	.name		= "ICPlus IP1001",
231	.phy_id_mask	= 0x0ffffff0,
232	.features	= PHY_GBIT_FEATURES | SUPPORTED_Pause |
233			  SUPPORTED_Asym_Pause,
234	.config_init	= &ip1001_config_init,
235	.config_aneg	= &genphy_config_aneg,
236	.read_status	= &genphy_read_status,
237	.suspend	= genphy_suspend,
238	.resume		= genphy_resume,
239	.driver		= { .owner = THIS_MODULE,},
240}, {
241	.phy_id		= 0x02430c54,
242	.name		= "ICPlus IP101A/G",
243	.phy_id_mask	= 0x0ffffff0,
244	.features	= PHY_BASIC_FEATURES | SUPPORTED_Pause |
245			  SUPPORTED_Asym_Pause,
246	.flags		= PHY_HAS_INTERRUPT,
247	.ack_interrupt	= ip101a_g_ack_interrupt,
248	.config_init	= &ip101a_g_config_init,
249	.config_aneg	= &genphy_config_aneg,
250	.read_status	= &genphy_read_status,
251	.suspend	= genphy_suspend,
252	.resume		= genphy_resume,
253	.driver		= { .owner = THIS_MODULE,},
254} };
255
256module_phy_driver(icplus_driver);
257
258static struct mdio_device_id __maybe_unused icplus_tbl[] = {
259	{ 0x02430d80, 0x0ffffff0 },
260	{ 0x02430d90, 0x0ffffff0 },
261	{ 0x02430c54, 0x0ffffff0 },
262	{ }
263};
264
265MODULE_DEVICE_TABLE(mdio, icplus_tbl);
266