1# 2# Misc strange devices 3# 4 5menu "Misc devices" 6 7config SENSORS_LIS3LV02D 8 tristate 9 depends on INPUT 10 select INPUT_POLLDEV 11 default n 12 13config AD525X_DPOT 14 tristate "Analog Devices Digital Potentiometers" 15 depends on (I2C || SPI) && SYSFS 16 help 17 If you say yes here, you get support for the Analog Devices 18 AD5258, AD5259, AD5251, AD5252, AD5253, AD5254, AD5255 19 AD5160, AD5161, AD5162, AD5165, AD5200, AD5201, AD5203, 20 AD5204, AD5206, AD5207, AD5231, AD5232, AD5233, AD5235, 21 AD5260, AD5262, AD5263, AD5290, AD5291, AD5292, AD5293, 22 AD7376, AD8400, AD8402, AD8403, ADN2850, AD5241, AD5242, 23 AD5243, AD5245, AD5246, AD5247, AD5248, AD5280, AD5282, 24 ADN2860, AD5273, AD5171, AD5170, AD5172, AD5173, AD5270, 25 AD5271, AD5272, AD5274 26 digital potentiometer chips. 27 28 See Documentation/misc-devices/ad525x_dpot.txt for the 29 userspace interface. 30 31 This driver can also be built as a module. If so, the module 32 will be called ad525x_dpot. 33 34config AD525X_DPOT_I2C 35 tristate "support I2C bus connection" 36 depends on AD525X_DPOT && I2C 37 help 38 Say Y here if you have a digital potentiometers hooked to an I2C bus. 39 40 To compile this driver as a module, choose M here: the 41 module will be called ad525x_dpot-i2c. 42 43config AD525X_DPOT_SPI 44 tristate "support SPI bus connection" 45 depends on AD525X_DPOT && SPI_MASTER 46 help 47 Say Y here if you have a digital potentiometers hooked to an SPI bus. 48 49 If unsure, say N (but it's safe to say "Y"). 50 51 To compile this driver as a module, choose M here: the 52 module will be called ad525x_dpot-spi. 53 54config ATMEL_TCLIB 55 bool "Atmel AT32/AT91 Timer/Counter Library" 56 depends on (AVR32 || ARCH_AT91) 57 help 58 Select this if you want a library to allocate the Timer/Counter 59 blocks found on many Atmel processors. This facilitates using 60 these blocks by different drivers despite processor differences. 61 62config ATMEL_TCB_CLKSRC 63 bool "TC Block Clocksource" 64 depends on ATMEL_TCLIB 65 default y 66 help 67 Select this to get a high precision clocksource based on a 68 TC block with a 5+ MHz base clock rate. Two timer channels 69 are combined to make a single 32-bit timer. 70 71 When GENERIC_CLOCKEVENTS is defined, the third timer channel 72 may be used as a clock event device supporting oneshot mode 73 (delays of up to two seconds) based on the 32 KiHz clock. 74 75config ATMEL_TCB_CLKSRC_BLOCK 76 int 77 depends on ATMEL_TCB_CLKSRC 78 prompt "TC Block" if CPU_AT32AP700X 79 default 0 80 range 0 1 81 help 82 Some chips provide more than one TC block, so you have the 83 choice of which one to use for the clock framework. The other 84 TC can be used for other purposes, such as PWM generation and 85 interval timing. 86 87config DUMMY_IRQ 88 tristate "Dummy IRQ handler" 89 default n 90 ---help--- 91 This module accepts a single 'irq' parameter, which it should register for. 92 The sole purpose of this module is to help with debugging of systems on 93 which spurious IRQs would happen on disabled IRQ vector. 94 95config IBM_ASM 96 tristate "Device driver for IBM RSA service processor" 97 depends on X86 && PCI && INPUT 98 ---help--- 99 This option enables device driver support for in-band access to the 100 IBM RSA (Condor) service processor in eServer xSeries systems. 101 The ibmasm device driver allows user space application to access 102 ASM (Advanced Systems Management) functions on the service 103 processor. The driver is meant to be used in conjunction with 104 a user space API. 105 The ibmasm driver also enables the OS to use the UART on the 106 service processor board as a regular serial port. To make use of 107 this feature serial driver support (CONFIG_SERIAL_8250) must be 108 enabled. 109 110 WARNING: This software may not be supported or function 111 correctly on your IBM server. Please consult the IBM ServerProven 112 website <http://www-03.ibm.com/systems/info/x86servers/serverproven/compat/us/> 113 for information on the specific driver level and support statement 114 for your IBM server. 115 116config PHANTOM 117 tristate "Sensable PHANToM (PCI)" 118 depends on PCI 119 help 120 Say Y here if you want to build a driver for Sensable PHANToM device. 121 122 This driver is only for PCI PHANToMs. 123 124 If you choose to build module, its name will be phantom. If unsure, 125 say N here. 126 127config INTEL_MID_PTI 128 tristate "Parallel Trace Interface for MIPI P1149.7 cJTAG standard" 129 depends on PCI && TTY && (X86_INTEL_MID || COMPILE_TEST) 130 default n 131 help 132 The PTI (Parallel Trace Interface) driver directs 133 trace data routed from various parts in the system out 134 through an Intel Penwell PTI port and out of the mobile 135 device for analysis with a debugging tool (Lauterbach or Fido). 136 137 You should select this driver if the target kernel is meant for 138 an Intel Atom (non-netbook) mobile device containing a MIPI 139 P1149.7 standard implementation. 140 141config SGI_IOC4 142 tristate "SGI IOC4 Base IO support" 143 depends on PCI 144 ---help--- 145 This option enables basic support for the IOC4 chip on certain 146 SGI IO controller cards (IO9, IO10, and PCI-RT). This option 147 does not enable any specific functions on such a card, but provides 148 necessary infrastructure for other drivers to utilize. 149 150 If you have an SGI Altix with an IOC4-based card say Y. 151 Otherwise say N. 152 153config TIFM_CORE 154 tristate "TI Flash Media interface support" 155 depends on PCI 156 help 157 If you want support for Texas Instruments(R) Flash Media adapters 158 you should select this option and then also choose an appropriate 159 host adapter, such as 'TI Flash Media PCI74xx/PCI76xx host adapter 160 support', if you have a TI PCI74xx compatible card reader, for 161 example. 162 You will also have to select some flash card format drivers. MMC/SD 163 cards are supported via 'MMC/SD Card support: TI Flash Media MMC/SD 164 Interface support (MMC_TIFM_SD)'. 165 166 To compile this driver as a module, choose M here: the module will 167 be called tifm_core. 168 169config TIFM_7XX1 170 tristate "TI Flash Media PCI74xx/PCI76xx host adapter support" 171 depends on PCI && TIFM_CORE 172 default TIFM_CORE 173 help 174 This option enables support for Texas Instruments(R) PCI74xx and 175 PCI76xx families of Flash Media adapters, found in many laptops. 176 To make actual use of the device, you will have to select some 177 flash card format drivers, as outlined in the TIFM_CORE Help. 178 179 To compile this driver as a module, choose M here: the module will 180 be called tifm_7xx1. 181 182config ICS932S401 183 tristate "Integrated Circuits ICS932S401" 184 depends on I2C 185 help 186 If you say yes here you get support for the Integrated Circuits 187 ICS932S401 clock control chips. 188 189 This driver can also be built as a module. If so, the module 190 will be called ics932s401. 191 192config ATMEL_SSC 193 tristate "Device driver for Atmel SSC peripheral" 194 depends on HAS_IOMEM && (AVR32 || ARCH_AT91 || COMPILE_TEST) 195 ---help--- 196 This option enables device driver support for Atmel Synchronized 197 Serial Communication peripheral (SSC). 198 199 The SSC peripheral supports a wide variety of serial frame based 200 communications, i.e. I2S, SPI, etc. 201 202 If unsure, say N. 203 204config ENCLOSURE_SERVICES 205 tristate "Enclosure Services" 206 default n 207 help 208 Provides support for intelligent enclosures (bays which 209 contain storage devices). You also need either a host 210 driver (SCSI/ATA) which supports enclosures 211 or a SCSI enclosure device (SES) to use these services. 212 213config SGI_XP 214 tristate "Support communication between SGI SSIs" 215 depends on NET 216 depends on (IA64_GENERIC || IA64_SGI_SN2 || IA64_SGI_UV || X86_UV) && SMP 217 select IA64_UNCACHED_ALLOCATOR if IA64_GENERIC || IA64_SGI_SN2 218 select GENERIC_ALLOCATOR if IA64_GENERIC || IA64_SGI_SN2 219 select SGI_GRU if X86_64 && SMP 220 ---help--- 221 An SGI machine can be divided into multiple Single System 222 Images which act independently of each other and have 223 hardware based memory protection from the others. Enabling 224 this feature will allow for direct communication between SSIs 225 based on a network adapter and DMA messaging. 226 227config CS5535_MFGPT 228 tristate "CS5535/CS5536 Geode Multi-Function General Purpose Timer (MFGPT) support" 229 depends on MFD_CS5535 230 default n 231 help 232 This driver provides access to MFGPT functionality for other 233 drivers that need timers. MFGPTs are available in the CS5535 and 234 CS5536 companion chips that are found in AMD Geode and several 235 other platforms. They have a better resolution and max interval 236 than the generic PIT, and are suitable for use as high-res timers. 237 You probably don't want to enable this manually; other drivers that 238 make use of it should enable it. 239 240config CS5535_MFGPT_DEFAULT_IRQ 241 int 242 depends on CS5535_MFGPT 243 default 7 244 help 245 MFGPTs on the CS5535 require an interrupt. The selected IRQ 246 can be overridden as a module option as well as by driver that 247 use the cs5535_mfgpt_ API; however, different architectures might 248 want to use a different IRQ by default. This is here for 249 architectures to set as necessary. 250 251config CS5535_CLOCK_EVENT_SRC 252 tristate "CS5535/CS5536 high-res timer (MFGPT) events" 253 depends on GENERIC_CLOCKEVENTS && CS5535_MFGPT 254 help 255 This driver provides a clock event source based on the MFGPT 256 timer(s) in the CS5535 and CS5536 companion chips. 257 MFGPTs have a better resolution and max interval than the 258 generic PIT, and are suitable for use as high-res timers. 259 260config HP_ILO 261 tristate "Channel interface driver for the HP iLO processor" 262 depends on PCI 263 default n 264 help 265 The channel interface driver allows applications to communicate 266 with iLO management processors present on HP ProLiant servers. 267 Upon loading, the driver creates /dev/hpilo/dXccbN files, which 268 can be used to gather data from the management processor, via 269 read and write system calls. 270 271 To compile this driver as a module, choose M here: the 272 module will be called hpilo. 273 274config SGI_GRU 275 tristate "SGI GRU driver" 276 depends on X86_UV && SMP 277 default n 278 select MMU_NOTIFIER 279 ---help--- 280 The GRU is a hardware resource located in the system chipset. The GRU 281 contains memory that can be mmapped into the user address space. This memory is 282 used to communicate with the GRU to perform functions such as load/store, 283 scatter/gather, bcopy, AMOs, etc. The GRU is directly accessed by user 284 instructions using user virtual addresses. GRU instructions (ex., bcopy) use 285 user virtual addresses for operands. 286 287 If you are not running on a SGI UV system, say N. 288 289config SGI_GRU_DEBUG 290 bool "SGI GRU driver debug" 291 depends on SGI_GRU 292 default n 293 ---help--- 294 This option enables additional debugging code for the SGI GRU driver. 295 If you are unsure, say N. 296 297config APDS9802ALS 298 tristate "Medfield Avago APDS9802 ALS Sensor module" 299 depends on I2C 300 help 301 If you say yes here you get support for the ALS APDS9802 ambient 302 light sensor. 303 304 This driver can also be built as a module. If so, the module 305 will be called apds9802als. 306 307config ISL29003 308 tristate "Intersil ISL29003 ambient light sensor" 309 depends on I2C && SYSFS 310 help 311 If you say yes here you get support for the Intersil ISL29003 312 ambient light sensor. 313 314 This driver can also be built as a module. If so, the module 315 will be called isl29003. 316 317config ISL29020 318 tristate "Intersil ISL29020 ambient light sensor" 319 depends on I2C 320 help 321 If you say yes here you get support for the Intersil ISL29020 322 ambient light sensor. 323 324 This driver can also be built as a module. If so, the module 325 will be called isl29020. 326 327config SENSORS_TSL2550 328 tristate "Taos TSL2550 ambient light sensor" 329 depends on I2C && SYSFS 330 help 331 If you say yes here you get support for the Taos TSL2550 332 ambient light sensor. 333 334 This driver can also be built as a module. If so, the module 335 will be called tsl2550. 336 337config SENSORS_BH1780 338 tristate "ROHM BH1780GLI ambient light sensor" 339 depends on I2C && SYSFS 340 help 341 If you say yes here you get support for the ROHM BH1780GLI 342 ambient light sensor. 343 344 This driver can also be built as a module. If so, the module 345 will be called bh1780gli. 346 347config SENSORS_BH1770 348 tristate "BH1770GLC / SFH7770 combined ALS - Proximity sensor" 349 depends on I2C 350 ---help--- 351 Say Y here if you want to build a driver for BH1770GLC (ROHM) or 352 SFH7770 (Osram) combined ambient light and proximity sensor chip. 353 354 To compile this driver as a module, choose M here: the 355 module will be called bh1770glc. If unsure, say N here. 356 357config SENSORS_APDS990X 358 tristate "APDS990X combined als and proximity sensors" 359 depends on I2C 360 default n 361 ---help--- 362 Say Y here if you want to build a driver for Avago APDS990x 363 combined ambient light and proximity sensor chip. 364 365 To compile this driver as a module, choose M here: the 366 module will be called apds990x. If unsure, say N here. 367 368config HMC6352 369 tristate "Honeywell HMC6352 compass" 370 depends on I2C 371 help 372 This driver provides support for the Honeywell HMC6352 compass, 373 providing configuration and heading data via sysfs. 374 375config DS1682 376 tristate "Dallas DS1682 Total Elapsed Time Recorder with Alarm" 377 depends on I2C 378 help 379 If you say yes here you get support for Dallas Semiconductor 380 DS1682 Total Elapsed Time Recorder. 381 382 This driver can also be built as a module. If so, the module 383 will be called ds1682. 384 385config SPEAR13XX_PCIE_GADGET 386 bool "PCIe gadget support for SPEAr13XX platform" 387 depends on ARCH_SPEAR13XX && BROKEN 388 default n 389 help 390 This option enables gadget support for PCIe controller. If 391 board file defines any controller as PCIe endpoint then a sysfs 392 entry will be created for that controller. User can use these 393 sysfs node to configure PCIe EP as per his requirements. 394 395config TI_DAC7512 396 tristate "Texas Instruments DAC7512" 397 depends on SPI && SYSFS 398 help 399 If you say yes here you get support for the Texas Instruments 400 DAC7512 16-bit digital-to-analog converter. 401 402 This driver can also be built as a module. If so, the module 403 will be called ti_dac7512. 404 405config VMWARE_BALLOON 406 tristate "VMware Balloon Driver" 407 depends on X86 && HYPERVISOR_GUEST 408 help 409 This is VMware physical memory management driver which acts 410 like a "balloon" that can be inflated to reclaim physical pages 411 by reserving them in the guest and invalidating them in the 412 monitor, freeing up the underlying machine pages so they can 413 be allocated to other guests. The balloon can also be deflated 414 to allow the guest to use more physical memory. 415 416 If unsure, say N. 417 418 To compile this driver as a module, choose M here: the 419 module will be called vmw_balloon. 420 421config ARM_CHARLCD 422 bool "ARM Ltd. Character LCD Driver" 423 depends on PLAT_VERSATILE 424 help 425 This is a driver for the character LCD found on the ARM Ltd. 426 Versatile and RealView Platform Baseboards. It doesn't do 427 very much more than display the text "ARM Linux" on the first 428 line and the Linux version on the second line, but that's 429 still useful. 430 431config BMP085 432 bool 433 depends on SYSFS 434 435config BMP085_I2C 436 tristate "BMP085 digital pressure sensor on I2C" 437 select BMP085 438 select REGMAP_I2C 439 depends on I2C && SYSFS 440 help 441 Say Y here if you want to support Bosch Sensortec's digital pressure 442 sensor hooked to an I2C bus. 443 444 To compile this driver as a module, choose M here: the 445 module will be called bmp085-i2c. 446 447config BMP085_SPI 448 tristate "BMP085 digital pressure sensor on SPI" 449 select BMP085 450 select REGMAP_SPI 451 depends on SPI_MASTER && SYSFS 452 help 453 Say Y here if you want to support Bosch Sensortec's digital pressure 454 sensor hooked to an SPI bus. 455 456 To compile this driver as a module, choose M here: the 457 module will be called bmp085-spi. 458 459config PCH_PHUB 460 tristate "Intel EG20T PCH/LAPIS Semicon IOH(ML7213/ML7223/ML7831) PHUB" 461 select GENERIC_NET_UTILS 462 depends on PCI && (X86_32 || COMPILE_TEST) 463 help 464 This driver is for PCH(Platform controller Hub) PHUB(Packet Hub) of 465 Intel Topcliff which is an IOH(Input/Output Hub) for x86 embedded 466 processor. The Topcliff has MAC address and Option ROM data in SROM. 467 This driver can access MAC address and Option ROM data in SROM. 468 469 This driver also can be used for LAPIS Semiconductor's IOH, 470 ML7213/ML7223/ML7831. 471 ML7213 which is for IVI(In-Vehicle Infotainment) use. 472 ML7223 IOH is for MP(Media Phone) use. 473 ML7831 IOH is for general purpose use. 474 ML7213/ML7223/ML7831 is companion chip for Intel Atom E6xx series. 475 ML7213/ML7223/ML7831 is completely compatible for Intel EG20T PCH. 476 477 To compile this driver as a module, choose M here: the module will 478 be called pch_phub. 479 480config USB_SWITCH_FSA9480 481 tristate "FSA9480 USB Switch" 482 depends on I2C 483 help 484 The FSA9480 is a USB port accessory detector and switch. 485 The FSA9480 is fully controlled using I2C and enables USB data, 486 stereo and mono audio, video, microphone and UART data to use 487 a common connector port. 488 489config LATTICE_ECP3_CONFIG 490 tristate "Lattice ECP3 FPGA bitstream configuration via SPI" 491 depends on SPI && SYSFS 492 select FW_LOADER 493 default n 494 help 495 This option enables support for bitstream configuration (programming 496 or loading) of the Lattice ECP3 FPGA family via SPI. 497 498 If unsure, say N. 499 500config SRAM 501 bool "Generic on-chip SRAM driver" 502 depends on HAS_IOMEM 503 select GENERIC_ALLOCATOR 504 help 505 This driver allows you to declare a memory region to be managed by 506 the genalloc API. It is supposed to be used for small on-chip SRAM 507 areas found on many SoCs. 508 509config VEXPRESS_SYSCFG 510 bool "Versatile Express System Configuration driver" 511 depends on VEXPRESS_CONFIG 512 default y 513 help 514 ARM Ltd. Versatile Express uses specialised platform configuration 515 bus. System Configuration interface is one of the possible means 516 of generating transactions on this bus. 517 518source "drivers/misc/c2port/Kconfig" 519source "drivers/misc/eeprom/Kconfig" 520source "drivers/misc/cb710/Kconfig" 521source "drivers/misc/ti-st/Kconfig" 522source "drivers/misc/lis3lv02d/Kconfig" 523source "drivers/misc/carma/Kconfig" 524source "drivers/misc/altera-stapl/Kconfig" 525source "drivers/misc/mei/Kconfig" 526source "drivers/misc/vmw_vmci/Kconfig" 527source "drivers/misc/mic/Kconfig" 528source "drivers/misc/genwqe/Kconfig" 529source "drivers/misc/echo/Kconfig" 530source "drivers/misc/cxl/Kconfig" 531endmenu 532