1if NLM_XLP_BOARD || NLM_XLR_BOARD
2
3if NLM_XLP_BOARD
4config DT_XLP_EVP
5	bool "Built-in device tree for XLP EVP boards"
6	default y
7	select BUILTIN_DTB
8	help
9	  Add an FDT blob for XLP EVP boards into the kernel.
10	  This DTB will be used if the firmware does not pass in a DTB
11	  pointer to the kernel.  The corresponding DTS file is at
12	  arch/mips/netlogic/dts/xlp_evp.dts
13
14config DT_XLP_SVP
15	bool "Built-in device tree for XLP SVP boards"
16	default y
17	select BUILTIN_DTB
18	help
19	  Add an FDT blob for XLP VP boards into the kernel.
20	  This DTB will be used if the firmware does not pass in a DTB
21	  pointer to the kernel.  The corresponding DTS file is at
22	  arch/mips/netlogic/dts/xlp_svp.dts
23
24config DT_XLP_FVP
25	bool "Built-in device tree for XLP FVP boards"
26	default y
27	select BUILTIN_DTB
28	help
29	  Add an FDT blob for XLP FVP board into the kernel.
30	  This DTB will be used if the firmware does not pass in a DTB
31	  pointer to the kernel.  The corresponding DTS file is at
32	  arch/mips/netlogic/dts/xlp_fvp.dts
33
34config DT_XLP_GVP
35	bool "Built-in device tree for XLP GVP boards"
36	default y
37	select BUILTIN_DTB
38	help
39	  Add an FDT blob for XLP GVP board into the kernel.
40	  This DTB will be used if the firmware does not pass in a DTB
41	  pointer to the kernel.  The corresponding DTS file is at
42	  arch/mips/netlogic/dts/xlp_gvp.dts
43
44config DT_XLP_RVP
45	bool "Built-in device tree for XLP RVP boards"
46	default y
47	help
48	  Add an FDT blob for XLP RVP board into the kernel.
49	  This DTB will be used if the firmware does not pass in a DTB
50	  pointer to the kernel.  The corresponding DTS file is at
51	  arch/mips/netlogic/dts/xlp_rvp.dts
52
53config NLM_MULTINODE
54	bool "Support for multi-chip boards"
55	depends on NLM_XLP_BOARD
56	default n
57	help
58	  Add support for boards with 2 or 4 XLPs connected over ICI.
59
60if NLM_MULTINODE
61choice
62	prompt "Number of XLPs on the board"
63	default NLM_MULTINODE_2
64	help
65	  In the multi-node case, specify the number of SoCs on the board.
66
67config NLM_MULTINODE_2
68	bool "Dual-XLP board"
69	help
70	  Support boards with upto two XLPs connected over ICI.
71
72config NLM_MULTINODE_4
73	bool "Quad-XLP board"
74	help
75	  Support boards with upto four XLPs connected over ICI.
76
77endchoice
78
79endif
80endif
81
82config NLM_COMMON
83	bool
84
85config IOMMU_HELPER
86	bool
87
88config NEED_SG_DMA_LENGTH
89	bool
90
91config SWIOTLB
92	def_bool y
93	select NEED_SG_DMA_LENGTH
94	select IOMMU_HELPER
95
96endif
97