1/*
2 * Common support for CompuLab SB-T35 used on SBC-T3530, SBC-T3517 and SBC-T3730
3 */
4
5/ {
6	tfp410: encoder@0 {
7		compatible = "ti,tfp410";
8
9		powerdown-gpios = <&gpio2 22 GPIO_ACTIVE_LOW>;  /* gpio_54 */
10
11		pinctrl-names = "default";
12		pinctrl-0 = <&tfp410_pins>;
13
14		ports {
15			#address-cells = <1>;
16			#size-cells = <0>;
17
18			port@0 {
19				reg = <0>;
20
21				tfp410_in: endpoint@0 {
22					remote-endpoint = <&dpi_out>;
23				};
24			};
25
26			port@1 {
27				reg = <1>;
28
29				tfp410_out: endpoint@0 {
30					remote-endpoint = <&dvi_connector_in>;
31				};
32			};
33		};
34	};
35
36	dvi0: connector@0 {
37		compatible = "dvi-connector";
38		label = "dvi";
39
40		port {
41			dvi_connector_in: endpoint {
42				remote-endpoint = <&tfp410_out>;
43			};
44		};
45	};
46
47	audio_amp: audio_amp {
48		compatible = "regulator-fixed";
49		regulator-name = "audio_amp";
50		pinctrl-names = "default";
51		pinctrl-0 = <&sb_t35_audio_amp>;
52		gpio = <&gpio2 29 GPIO_ACTIVE_LOW>;   /* gpio_61 */
53		enable-active-low;
54		regulator-always-on;
55	};
56};
57
58&omap3_pmx_core {
59	smsc2_pins: pinmux_smsc2_pins {
60		pinctrl-single,pins = <
61			OMAP3_CORE1_IOPAD(0x20b6, PIN_OUTPUT | MUX_MODE0)	/* gpmc_ncs4.gpmc_ncs4 */
62			OMAP3_CORE1_IOPAD(0x20d2, PIN_INPUT_PULLUP | MUX_MODE4)	/* gpmc_wait3.gpio_65 */
63		>;
64	};
65
66	tfp410_pins: pinmux_tfp410_pins {
67		pinctrl-single,pins = <
68			OMAP3_CORE1_IOPAD(0x20b4, PIN_OUTPUT | MUX_MODE4)	/* gpmc_ncs3.gpio_54 */
69		>;
70	};
71
72	i2c3_pins: pinmux_i2c3_pins {
73		pinctrl-single,pins = <
74			OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl */
75			OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda */
76		>;
77	};
78
79	sb_t35_audio_amp: pinmux_sb_t35_audio_amp {
80		pinctrl-single,pins = <
81			OMAP3_CORE1_IOPAD(0x20c8, PIN_OUTPUT | MUX_MODE4) /* gpmc_nbe1.gpio_61 */
82		>;
83	};
84};
85
86&i2c3 {
87	pinctrl-names = "default";
88	pinctrl-0 = <&i2c3_pins>;
89
90	clock-frequency = <400000>;
91
92	at24@50 {
93		compatible = "at24,24c02";
94		pagesize = <16>;
95		reg = <0x50>;
96	};
97};
98
99&gpmc {
100	ranges = <4 0 0x2d000000 0x01000000>;
101
102	smsc2: ethernet@4,0 {
103		compatible = "smsc,lan9221", "smsc,lan9115";
104		pinctrl-names = "default";
105		pinctrl-0 = <&smsc2_pins>;
106		interrupt-parent = <&gpio3>;
107		interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
108		reg = <4 0 0xff>;
109		bank-width = <2>;
110		gpmc,device-width = <1>;
111		gpmc,cycle2cycle-samecsen = <1>;
112		gpmc,cycle2cycle-diffcsen = <1>;
113		gpmc,cs-on-ns = <5>;
114		gpmc,cs-rd-off-ns = <150>;
115		gpmc,cs-wr-off-ns = <150>;
116		gpmc,adv-on-ns = <0>;
117		gpmc,adv-rd-off-ns = <15>;
118		gpmc,adv-wr-off-ns = <40>;
119		gpmc,oe-on-ns = <45>;
120		gpmc,oe-off-ns = <140>;
121		gpmc,we-on-ns = <45>;
122		gpmc,we-off-ns = <140>;
123		gpmc,rd-cycle-ns = <155>;
124		gpmc,wr-cycle-ns = <155>;
125		gpmc,access-ns = <120>;
126		gpmc,page-burst-access-ns = <20>;
127		gpmc,bus-turnaround-ns = <75>;
128		gpmc,cycle2cycle-delay-ns = <75>;
129		gpmc,wait-monitoring-ns = <0>;
130		gpmc,clk-activation-ns = <0>;
131		gpmc,wr-data-mux-bus-ns = <0>;
132		gpmc,wr-access-ns = <0>;
133		vddvario-supply = <&vddvario>;
134		vdd33a-supply = <&vdd33a>;
135		reg-io-width = <4>;
136		smsc,save-mac-address;
137	};
138};
139