1/*
2 * Support for CompuLab CM-T3730
3 */
4/dts-v1/;
5
6#include "omap36xx.dtsi"
7#include "omap3-cm-t3x30.dtsi"
8
9/ {
10	model = "CompuLab CM-T3730";
11	compatible = "compulab,omap3-cm-t3730", "ti,omap36xx", "ti,omap3";
12
13	wl12xx_vmmc2: wl12xx_vmmc2 {
14		compatible = "regulator-fixed";
15		regulator-name = "vw1271";
16		pinctrl-names = "default";
17		pinctrl-0 = <&wl12xx_gpio>;
18		regulator-min-microvolt = <1800000>;
19		regulator-max-microvolt = <1800000>;
20		gpio = <&gpio3 9 GPIO_ACTIVE_HIGH>;   /* gpio73 */
21		startup-delay-us = <20000>;
22		enable-active-high;
23	};
24
25	wl12xx_vaux2: wl12xx_vaux2 {
26		compatible = "regulator-fixed";
27		regulator-name = "vwl1271_vaux2";
28		regulator-min-microvolt = <1800000>;
29		regulator-max-microvolt = <1800000>;
30		vin-supply = <&vaux2>;
31	};
32};
33
34&omap3_pmx_wkup {
35	dss_dpi_pins_cm_t3730: pinmux_dss_dpi_pins_cm_t3730 {
36		pinctrl-single,pins = <
37			OMAP3_WKUP_IOPAD(0x2a08, PIN_OUTPUT | MUX_MODE3)   /* sys_boot0.dss_data18 */
38			OMAP3_WKUP_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE3)   /* sys_boot1.dss_data19 */
39			OMAP3_WKUP_IOPAD(0x2a10, PIN_OUTPUT | MUX_MODE3)   /* sys_boot3.dss_data20 */
40			OMAP3_WKUP_IOPAD(0x2a12, PIN_OUTPUT | MUX_MODE3)   /* sys_boot4.dss_data21 */
41			OMAP3_WKUP_IOPAD(0x2a14, PIN_OUTPUT | MUX_MODE3)   /* sys_boot5.dss_data22 */
42			OMAP3_WKUP_IOPAD(0x2a16, PIN_OUTPUT | MUX_MODE3)   /* sys_boot6.dss_data23 */
43		>;
44	};
45};
46
47&omap3_pmx_core {
48
49	mmc2_pins: pinmux_mmc2_pins {
50		pinctrl-single,pins = <
51			OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_clk.sdmmc2_clk */
52			OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_cmd.sdmmc2_cmd */
53			OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat0.sdmmc2_dat0 */
54			OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat1.sdmmc2_dat1 */
55			OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat2.sdmmc2_dat2 */
56			OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat3.sdmmc2_dat3 */
57		>;
58	};
59
60	wl12xx_gpio: pinmux_wl12xx_gpio {
61		pinctrl-single,pins = <
62			OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE4)	/* dss_data3.gpio_73 */
63			OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT | MUX_MODE4)	/* sdmmc2_dat4.gpio_136 */
64		>;
65	};
66};
67
68&mmc2 {
69	pinctrl-names = "default";
70	pinctrl-0 = <&mmc2_pins>;
71	vmmc-supply = <&wl12xx_vmmc2>;
72	vmmc_aux-supply = <&wl12xx_vaux2>;
73	non-removable;
74	bus-width = <4>;
75	cap-power-off-card;
76
77	#address-cells = <1>;
78	#size-cells = <0>;
79	wlcore: wlcore@2 {
80		compatible = "ti,wl1271";
81		reg = <2>;
82		interrupt-parent = <&gpio5>;
83		interrupts = <8 IRQ_TYPE_LEVEL_HIGH>; /* gpio 136 */
84		ref-clock-frequency = <38400000>;
85	};
86};
87
88&dss {
89	status = "ok";
90
91	pinctrl-names = "default";
92	pinctrl-0 = <
93		&dss_dpi_pins_common
94		&dss_dpi_pins_cm_t3730
95	>;
96};
97
98