1Kernel driver for LP5562
2========================
3
4* TI LP5562 LED Driver
5
6Author: Milo(Woogyom) Kim <milo.kim@ti.com>
7
8Description
9
10  LP5562 can drive up to 4 channels. R/G/B and White.
11  LEDs can be controlled directly via the led class control interface.
12
13  All four channels can be also controlled using the engine micro programs.
14  LP5562 has the internal program memory for running various LED patterns.
15  For the details, please refer to 'firmware' section in leds-lp55xx.txt
16
17Device attribute: engine_mux
18
19  3 Engines are allocated in LP5562, but the number of channel is 4.
20  Therefore each channel should be mapped to the engine number.
21  Value : RGB or W
22
23  This attribute is used for programming LED data with the firmware interface.
24  Unlike the LP5521/LP5523/55231, LP5562 has unique feature for the engine mux,
25  so additional sysfs is required.
26
27  LED Map
28  Red   ... Engine 1 (fixed)
29  Green ... Engine 2 (fixed)
30  Blue  ... Engine 3 (fixed)
31  White ... Engine 1 or 2 or 3 (selective)
32
33How to load the program data using engine_mux
34
35  Before loading the LP5562 program data, engine_mux should be written between
36  the engine selection and loading the firmware.
37  Engine mux has two different mode, RGB and W.
38  RGB is used for loading RGB program data, W is used for W program data.
39
40  For example, run blinking green channel pattern,
41  echo 2 > /sys/bus/i2c/devices/xxxx/select_engine     # 2 is for green channel
42  echo "RGB" > /sys/bus/i2c/devices/xxxx/engine_mux    # engine mux for RGB
43  echo 1 > /sys/class/firmware/lp5562/loading
44  echo "4000600040FF6000" > /sys/class/firmware/lp5562/data
45  echo 0 > /sys/class/firmware/lp5562/loading
46  echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
47
48  To run a blinking white pattern,
49  echo 1 or 2 or 3 > /sys/bus/i2c/devices/xxxx/select_engine
50  echo "W" > /sys/bus/i2c/devices/xxxx/engine_mux
51  echo 1 > /sys/class/firmware/lp5562/loading
52  echo "4000600040FF6000" > /sys/class/firmware/lp5562/data
53  echo 0 > /sys/class/firmware/lp5562/loading
54  echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
55
56How to load the predefined patterns
57
58  Please refer to 'leds-lp55xx.txt"
59
60Setting Current of Each Channel
61
62  Like LP5521 and LP5523/55231, LP5562 provides LED current settings.
63  The 'led_current' and 'max_current' are used.
64
65(Example of Platform data)
66
67To configure the platform specific data, lp55xx_platform_data structure is used.
68
69static struct lp55xx_led_config lp5562_led_config[] = {
70	{
71		.name 		= "R",
72		.chan_nr	= 0,
73		.led_current	= 20,
74		.max_current	= 40,
75	},
76	{
77		.name 		= "G",
78		.chan_nr	= 1,
79		.led_current	= 20,
80		.max_current	= 40,
81	},
82	{
83		.name 		= "B",
84		.chan_nr	= 2,
85		.led_current	= 20,
86		.max_current	= 40,
87	},
88	{
89		.name 		= "W",
90		.chan_nr	= 3,
91		.led_current	= 20,
92		.max_current	= 40,
93	},
94};
95
96static int lp5562_setup(void)
97{
98	/* setup HW resources */
99}
100
101static void lp5562_release(void)
102{
103	/* Release HW resources */
104}
105
106static void lp5562_enable(bool state)
107{
108	/* Control of chip enable signal */
109}
110
111static struct lp55xx_platform_data lp5562_platform_data = {
112        .led_config     = lp5562_led_config,
113        .num_channels   = ARRAY_SIZE(lp5562_led_config),
114        .setup_resources   = lp5562_setup,
115        .release_resources = lp5562_release,
116        .enable            = lp5562_enable,
117};
118
119If the current is set to 0 in the platform data, that channel is
120disabled and it is not visible in the sysfs.
121