1TI PHY: DT DOCUMENTATION FOR PHYs in TI PLATFORMs
2
3OMAP CONTROL PHY
4
5Required properties:
6 - compatible: Should be one of
7 "ti,control-phy-otghs" - if it has otghs_control mailbox register as on OMAP4.
8 "ti,control-phy-usb2" - if it has Power down bit in control_dev_conf register
9                        e.g. USB2_PHY on OMAP5.
10 "ti,control-phy-pipe3" - if it has DPLL and individual Rx & Tx power control
11                        e.g. USB3 PHY and SATA PHY on OMAP5.
12 "ti,control-phy-pcie" - for pcie to support external clock for pcie and to
13			set PCS delay value.
14			e.g. PCIE PHY in DRA7x
15 "ti,control-phy-usb2-dra7" - if it has power down register like USB2 PHY on
16                        DRA7 platform.
17 "ti,control-phy-usb2-am437" - if it has power down register like USB2 PHY on
18                        AM437 platform.
19 - reg : register ranges as listed in the reg-names property
20 - reg-names: "otghs_control" for control-phy-otghs
21	      "power", "pcie_pcs" and "control_sma" for control-phy-pcie
22	      "power" for all other types
23
24omap_control_usb: omap-control-usb@4a002300 {
25        compatible = "ti,control-phy-otghs";
26        reg = <0x4a00233c 0x4>;
27        reg-names = "otghs_control";
28};
29
30OMAP USB2 PHY
31
32Required properties:
33 - compatible: Should be "ti,omap-usb2"
34 - reg : Address and length of the register set for the device.
35 - #phy-cells: determine the number of cells that should be given in the
36   phandle while referencing this phy.
37 - clocks: a list of phandles and clock-specifier pairs, one for each entry in
38   clock-names.
39 - clock-names: should include:
40   * "wkupclk" - wakeup clock.
41   * "refclk" - reference clock (optional).
42
43Optional properties:
44 - ctrl-module : phandle of the control module used by PHY driver to power on
45   the PHY.
46
47This is usually a subnode of ocp2scp to which it is connected.
48
49usb2phy@4a0ad080 {
50	compatible = "ti,omap-usb2";
51	reg = <0x4a0ad080 0x58>;
52	ctrl-module = <&omap_control_usb>;
53	#phy-cells = <0>;
54	clocks = <&usb_phy_cm_clk32k>, <&usb_otg_ss_refclk960m>;
55	clock-names = "wkupclk", "refclk";
56};
57
58TI PIPE3 PHY
59
60Required properties:
61 - compatible: Should be "ti,phy-usb3", "ti,phy-pipe3-sata" or
62   "ti,phy-pipe3-pcie. "ti,omap-usb3" is deprecated.
63 - reg : Address and length of the register set for the device.
64 - reg-names: The names of the register addresses corresponding to the registers
65   filled in "reg".
66 - #phy-cells: determine the number of cells that should be given in the
67   phandle while referencing this phy.
68 - clocks: a list of phandles and clock-specifier pairs, one for each entry in
69   clock-names.
70 - clock-names: should include:
71   * "wkupclk" - wakeup clock.
72   * "sysclk" - system clock.
73   * "refclk" - reference clock.
74   * "dpll_ref" - external dpll ref clk
75   * "dpll_ref_m2" - external dpll ref clk
76   * "phy-div" - divider for apll
77   * "div-clk" - apll clock
78
79Optional properties:
80 - ctrl-module : phandle of the control module used by PHY driver to power on
81   the PHY.
82 - id: If there are multiple instance of the same type, in order to
83   differentiate between each instance "id" can be used (e.g., multi-lane PCIe
84   PHY). If "id" is not provided, it is set to default value of '1'.
85
86This is usually a subnode of ocp2scp to which it is connected.
87
88usb3phy@4a084400 {
89	compatible = "ti,phy-usb3";
90	reg = <0x4a084400 0x80>,
91	      <0x4a084800 0x64>,
92	      <0x4a084c00 0x40>;
93	reg-names = "phy_rx", "phy_tx", "pll_ctrl";
94	ctrl-module = <&omap_control_usb>;
95	#phy-cells = <0>;
96	clocks = <&usb_phy_cm_clk32k>,
97		 <&sys_clkin>,
98		 <&usb_otg_ss_refclk960m>;
99	clock-names =	"wkupclk",
100			"sysclk",
101			"refclk";
102};
103