1* DMA40 DMA Controller
2
3Required properties:
4- compatible: "stericsson,dma40"
5- reg: Address range of the DMAC registers
6- reg-names: Names of the above areas to use during resource look-up
7- interrupt: Should contain the DMAC interrupt number
8- #dma-cells: must be <3>
9- memcpy-channels: Channels to be used for memcpy
10
11Optional properties:
12- dma-channels: Number of channels supported by hardware - if not present
13		the driver will attempt to obtain the information from H/W
14- disabled-channels: Channels which can not be used
15
16Example:
17
18	dma: dma-controller@801C0000 {
19		compatible = "stericsson,db8500-dma40", "stericsson,dma40";
20		reg = <0x801C0000 0x1000  0x40010000 0x800>;
21		reg-names = "base", "lcpa";
22		interrupt-parent = <&intc>;
23		interrupts = <0 25 0x4>;
24
25		#dma-cells = <2>;
26		memcpy-channels  = <56 57 58 59 60>;
27		disabled-channels  = <12>;
28		dma-channels = <8>;
29	};
30
31Clients
32Required properties:
33- dmas: Comma separated list of dma channel requests
34- dma-names: Names of the aforementioned requested channels
35
36Each dmas request consists of 4 cells:
37  1. A phandle pointing to the DMA controller
38  2. Device signal number, the signal line for single and burst requests
39     connected from the device to the DMA40 engine
40  3. The DMA request line number (only when 'use fixed channel' is set)
41  4. A 32bit mask specifying; mode, direction and endianness
42     [NB: This list will grow]
43        0x00000001: Mode:
44                Logical channel when unset
45                Physical channel when set
46        0x00000002: Direction:
47                Memory to Device when unset
48                Device to Memory when set
49        0x00000004: Endianness:
50                Little endian when unset
51                Big endian when set
52        0x00000008: Use fixed channel:
53                Use automatic channel selection when unset
54                Use DMA request line number when set
55        0x00000010: Set channel as high priority:
56                Normal priority when unset
57                High priority when set
58
59Existing signal numbers for the DB8500 ASIC. Unless specified, the signals are
60bidirectional, i.e. the same for RX and TX operations:
61
620:  SPI controller 0
631:  SD/MMC controller 0 (unused)
642:  SD/MMC controller 1 (unused)
653:  SD/MMC controller 2 (unused)
664:  I2C port 1
675:  I2C port 3
686:  I2C port 2
697:  I2C port 4
708:  Synchronous Serial Port SSP0
719:  Synchronous Serial Port SSP1
7210: Multi-Channel Display Engine MCDE RX
7311: UART port 2
7412: UART port 1
7513: UART port 0
7614: Multirate Serial Port MSP2
7715: I2C port 0
7816: USB OTG in/out endpoints 7 & 15
7917: USB OTG in/out endpoints 6 & 14
8018: USB OTG in/out endpoints 5 & 13
8119: USB OTG in/out endpoints 4 & 12
8220: SLIMbus or HSI channel 0
8321: SLIMbus or HSI channel 1
8422: SLIMbus or HSI channel 2
8523: SLIMbus or HSI channel 3
8624: Multimedia DSP SXA0
8725: Multimedia DSP SXA1
8826: Multimedia DSP SXA2
8927: Multimedia DSP SXA3
9028: SD/MM controller 2
9129: SD/MM controller 0
9230: MSP port 1 on DB8500 v1, MSP port 3 on DB8500 v2
9331: MSP port 0 or SLIMbus channel 0
9432: SD/MM controller 1
9533: SPI controller 2
9634: i2c3 RX2 TX2
9735: SPI controller 1
9836: USB OTG in/out endpoints 3 & 11
9937: USB OTG in/out endpoints 2 & 10
10038: USB OTG in/out endpoints 1 & 9
10139: USB OTG in/out endpoints 8
10240: SPI controller 3
10341: SD/MM controller 3
10442: SD/MM controller 4
10543: SD/MM controller 5
10644: Multimedia DSP SXA4
10745: Multimedia DSP SXA5
10846: SLIMbus channel 8 or Multimedia DSP SXA6
10947: SLIMbus channel 9 or Multimedia DSP SXA7
11048: Crypto Accelerator 1
11149: Crypto Accelerator 1 TX or Hash Accelerator 1 TX
11250: Hash Accelerator 1 TX
11351: memcpy TX (to be used by the DMA driver for memcpy operations)
11452: SLIMbus or HSI channel 4
11553: SLIMbus or HSI channel 5
11654: SLIMbus or HSI channel 6
11755: SLIMbus or HSI channel 7
11856: memcpy (to be used by the DMA driver for memcpy operations)
11957: memcpy (to be used by the DMA driver for memcpy operations)
12058: memcpy (to be used by the DMA driver for memcpy operations)
12159: memcpy (to be used by the DMA driver for memcpy operations)
12260: memcpy (to be used by the DMA driver for memcpy operations)
12361: Crypto Accelerator 0
12462: Crypto Accelerator 0 TX or Hash Accelerator 0 TX
12563: Hash Accelerator 0 TX
126
127Example:
128
129	uart@80120000 {
130		compatible = "arm,pl011", "arm,primecell";
131		reg = <0x80120000 0x1000>;
132		interrupts = <0 11 0x4>;
133
134		dmas = <&dma 13 0 0x2>, /* Logical - DevToMem */
135		       <&dma 13 0 0x0>; /* Logical - MemToDev */
136		dma-names = "rx", "rx";
137
138		status = "disabled";
139	};
140