1
2     CPU frequency and voltage scaling statistics in the Linux(TM) kernel
3
4
5             L i n u x    c p u f r e q - s t a t s   d r i v e r
6
7                       - information for users -
8
9
10             Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
11
12Contents
131. Introduction
142. Statistics Provided (with example)
153. Configuring cpufreq-stats
16
17
181. Introduction
19
20cpufreq-stats is a driver that provides CPU frequency statistics for each CPU.
21These statistics are provided in /sysfs as a bunch of read_only interfaces. This
22interface (when configured) will appear in a separate directory under cpufreq
23in /sysfs (<sysfs root>/devices/system/cpu/cpuX/cpufreq/stats/) for each CPU.
24Various statistics will form read_only files under this directory.
25
26This driver is designed to be independent of any particular cpufreq_driver
27that may be running on your CPU. So, it will work with any cpufreq_driver.
28
29
302. Statistics Provided (with example)
31
32cpufreq stats provides following statistics (explained in detail below).
33-  time_in_state
34-  total_trans
35-  trans_table
36
37All the statistics will be from the time the stats driver has been inserted 
38to the time when a read of a particular statistic is done. Obviously, stats 
39driver will not have any information about the frequency transitions before
40the stats driver insertion.
41
42--------------------------------------------------------------------------------
43<mysystem>:/sys/devices/system/cpu/cpu0/cpufreq/stats # ls -l
44total 0
45drwxr-xr-x  2 root root    0 May 14 16:06 .
46drwxr-xr-x  3 root root    0 May 14 15:58 ..
47-r--r--r--  1 root root 4096 May 14 16:06 time_in_state
48-r--r--r--  1 root root 4096 May 14 16:06 total_trans
49-r--r--r--  1 root root 4096 May 14 16:06 trans_table
50--------------------------------------------------------------------------------
51
52-  time_in_state
53This gives the amount of time spent in each of the frequencies supported by
54this CPU. The cat output will have "<frequency> <time>" pair in each line, which
55will mean this CPU spent <time> usertime units of time at <frequency>. Output
56will have one line for each of the supported frequencies. usertime units here 
57is 10mS (similar to other time exported in /proc).
58
59--------------------------------------------------------------------------------
60<mysystem>:/sys/devices/system/cpu/cpu0/cpufreq/stats # cat time_in_state 
613600000 2089
623400000 136
633200000 34
643000000 67
652800000 172488
66--------------------------------------------------------------------------------
67
68
69-  total_trans
70This gives the total number of frequency transitions on this CPU. The cat 
71output will have a single count which is the total number of frequency
72transitions.
73
74--------------------------------------------------------------------------------
75<mysystem>:/sys/devices/system/cpu/cpu0/cpufreq/stats # cat total_trans
7620
77--------------------------------------------------------------------------------
78
79-  trans_table
80This will give a fine grained information about all the CPU frequency
81transitions. The cat output here is a two dimensional matrix, where an entry
82<i,j> (row i, column j) represents the count of number of transitions from 
83Freq_i to Freq_j. Freq_i is in descending order with increasing rows and 
84Freq_j is in descending order with increasing columns. The output here also 
85contains the actual freq values for each row and column for better readability.
86
87--------------------------------------------------------------------------------
88<mysystem>:/sys/devices/system/cpu/cpu0/cpufreq/stats # cat trans_table
89   From  :    To
90         :   3600000   3400000   3200000   3000000   2800000 
91  3600000:         0         5         0         0         0 
92  3400000:         4         0         2         0         0 
93  3200000:         0         1         0         2         0 
94  3000000:         0         0         1         0         3 
95  2800000:         0         0         0         2         0 
96--------------------------------------------------------------------------------
97
98
993. Configuring cpufreq-stats
100
101To configure cpufreq-stats in your kernel
102Config Main Menu
103	Power management options (ACPI, APM)  --->
104		CPU Frequency scaling  --->
105			[*] CPU Frequency scaling
106			<*>   CPU frequency translation statistics 
107			[*]     CPU frequency translation statistics details
108
109
110"CPU Frequency scaling" (CONFIG_CPU_FREQ) should be enabled to configure
111cpufreq-stats.
112
113"CPU frequency translation statistics" (CONFIG_CPU_FREQ_STAT) provides the
114basic statistics which includes time_in_state and total_trans.
115
116"CPU frequency translation statistics details" (CONFIG_CPU_FREQ_STAT_DETAILS)
117provides fine grained cpufreq stats by trans_table. The reason for having a
118separate config option for trans_table is:
119- trans_table goes against the traditional /sysfs rule of one value per
120  interface. It provides a whole bunch of value in a 2 dimensional matrix
121  form.
122
123Once these two options are enabled and your CPU supports cpufrequency, you
124will be able to see the CPU frequency statistics in /sysfs.
125
126
127
128
129