Searched refs:HOLD (Results 1 - 16 of 16) sorted by relevance
| /linux-4.4.14/drivers/gpu/drm/sti/ |
| H A D | sti_awg_utils.c | 20 HOLD, enumerator in enum:opcode
93 case HOLD: awg_generate_instr()
|
| /linux-4.4.14/fs/xfs/ |
| H A D | xfs_buf_item.h | 34 { XFS_BLI_HOLD, "HOLD" }, \
|
| /linux-4.4.14/drivers/mtd/nand/ |
| H A D | txx9ndfmc.c | 298 hold -= 2; /* actual hold time : (HOLD + 2) BUSCLK */ txx9ndfmc_probe()
304 dev_info(&dev->dev, "CLK:%ldMHz HOLD:%d SPW:%d\n", txx9ndfmc_probe()
|
| /linux-4.4.14/drivers/ata/ |
| H A D | sata_via.c | 579 * When host issues HOLD, device may send up to 20DW of data svia_configure()
582 * send up to 40DW before acknowledging HOLD and, in the svia_configure()
589 * means host will issue HOLD to device when the left FIFO svia_configure()
|
| /linux-4.4.14/drivers/mmc/host/ |
| H A D | dw_mmc-exynos.c | 211 * optionally bypassing the HOLD register for command and data. The dw_mci_exynos_prepare_command()
212 * HOLD register should be bypassed in case there is no phase shift dw_mci_exynos_prepare_command()
|
| /linux-4.4.14/drivers/spi/ |
| H A D | spi-falcon.c | 340 * set some bits of unused_wd, to not trigger HOLD/WP falcon_sflash_setup()
|
| /linux-4.4.14/arch/arm/mach-pxa/ |
| H A D | saar.c | 191 SMART_CMD(0x32), /* Timing(3), ASW HOLD=0.5CLK */
|
| H A D | tavorevb.c | 280 SMART_CMD(0x14), /* Timing(3), ASW HOLD=0.5CLK */
|
| /linux-4.4.14/drivers/isdn/hisax/ |
| H A D | q931.c | 67 0x24, "HOLD"
70 0x28, "HOLD ACKNOWLEDGE"
73 0x30, "HOLD REJECT"
|
| /linux-4.4.14/drivers/i2c/busses/ |
| H A D | i2c-cadence.c | 138 * @bus_hold_flag: Flag used in repeated start for clearing HOLD bit
256 * register reaches zero without considering the HOLD bit. cdns_i2c_isr()
584 * master receive message if HOLD bit is set (repeated start), cdns_i2c_master_xfer()
|
| /linux-4.4.14/drivers/scsi/ |
| H A D | dpt_i2o.c | 221 /* Active IOPs in HOLD state */ adpt_detect()
236 PDEBUG("HBA's in HOLD state\n"); adpt_detect()
843 PDEBUG("%s: in HOLD state\n",pHba->name); adpt_hba_reset()
2707 * Bring an I2O controller into HOLD state. See the spec.
2752 /* In HOLD state */ adpt_i2o_activate_hba()
3019 printk("HOLD\n"); adpt_i2o_status_get()
|
| /linux-4.4.14/sound/pci/asihpi/ |
| H A D | hpi6000.c | 821 7 NOHOLD = 1 external HOLD disabled hpi6000_adapter_boot_load_dsp()
823 9 HOLD = 0 HOLD input is low hpi6000_adapter_boot_load_dsp()
|
| /linux-4.4.14/drivers/net/wan/ |
| H A D | dscc4.c | 42 * doesn't use HOLD mode any more. HOLD mode is definitely buggy and the more
1819 * avoid HOLD in the BRDA-to-be-pointed desc. dscc4_rx_irq()
|
| /linux-4.4.14/drivers/scsi/isci/ |
| H A D | phy.c | 590 * SPINUP HOLD event when the state machine was expecting a SAS PHY event. none sci_phy_start_sata_link_training()
|
| /linux-4.4.14/fs/ceph/ |
| H A D | addr.c | 718 (wbc->sync_mode == WB_SYNC_ALL ? "ALL" : "HOLD")); ceph_writepages_start()
|
| /linux-4.4.14/drivers/isdn/hardware/eicon/ |
| H A D | message.c | 14455 dbug(1, dprintf("[%06lx] %s,%d: HOLD save...", hold_save_command()
14461 dbug(1, dprintf("[%06lx] %s,%d: HOLD save failed", hold_save_command()
|
Completed in 1372 milliseconds