| /linux-4.4.14/drivers/staging/gdm72xx/ |
| D | Kconfig | 18 transmitting packets.
30 Enable support for transmitting multiple packets (packet
|
| /linux-4.4.14/drivers/net/team/ |
| D | Kconfig | 32 Basic mode where port used for transmitting packets is selected in
44 Basic mode where port used for transmitting packets is selected
|
| /linux-4.4.14/drivers/media/rc/ |
| D | redrat3.c | 196 bool transmitting; member
227 if (!rr3->transmitting && (code != 0x40)) in redrat3_dump_fw_error()
269 if (!rr3->transmitting) in redrat3_dump_fw_error()
726 if (rr3->transmitting) { in redrat3_transmit_ir()
735 rr3->transmitting = true; in redrat3_transmit_ir()
812 rr3->transmitting = false; in redrat3_transmit_ir()
|
| D | ite-cir.c | 232 bool for_tx = dev->transmitting; in ite_set_carrier_params()
404 dev->transmitting = true; in ite_tx_ir()
518 dev->transmitting = false; in ite_tx_ir()
1333 wait_event_interruptible(dev->tx_ended, !dev->transmitting); in ite_close()
1655 wait_event_interruptible(dev->tx_ended, !dev->transmitting); in ite_suspend()
|
| D | ite-cir.h | 132 bool in_use, transmitting; member
|
| D | Kconfig | 24 encoding for IR transmitting (aka "blasting").
|
| /linux-4.4.14/drivers/usb/class/ |
| D | cdc-acm.h | 101 int transmitting; member
|
| D | cdc-acm.c | 204 acm->transmitting--; in acm_write_done()
218 acm->transmitting++; in acm_start_wb()
1587 if (acm->transmitting) { in acm_suspend()
|
| /linux-4.4.14/Documentation/scsi/ |
| D | cxgb3i.txt | 14 On transmitting, Chelsio S3 h/w computes and inserts the Header and
28 On transmitting, S3 h/w accepts the complete PDU (header + data)
|
| /linux-4.4.14/Documentation/devicetree/bindings/media/ |
| D | st-rc.txt | 14 protocol used for transmitting remote control signals. tx-mode should
|
| /linux-4.4.14/Documentation/devicetree/bindings/sound/ |
| D | imx-audio-spdif.txt | 15 transmitting function of S/PDIF will be enabled,
|
| /linux-4.4.14/Documentation/video4linux/cx2341x/ |
| D | README.hm12 | 17 transmitting this block the first line of the block on the right to the
25 second line of 8 UV pairs of the top-left block, etc. After transmitting
|
| /linux-4.4.14/arch/cris/ |
| D | Kconfig | 362 used when transmitting data.
372 used when transmitting data.
466 used when transmitting data.
489 used when transmitting data.
499 used when transmitting data.
|
| /linux-4.4.14/drivers/net/hippi/ |
| D | Kconfig | 35 transmitting and receiving. This memory cannot be used by any other
|
| /linux-4.4.14/Documentation/devicetree/bindings/serial/ |
| D | atmel-usart.txt | 16 - atmel,use-dma-tx: use of PDC or DMA for transmitting data
|
| /linux-4.4.14/drivers/staging/most/Documentation/ |
| D | driver_usage.txt | 114 When transmitting synchronous data the allocated channel width needs to be
132 When transmitting isochronous AVP data the desired packet size needs to be
|
| /linux-4.4.14/Documentation/input/ |
| D | userio.txt | 49 Registers the port with the serio driver and begins transmitting data back and
|
| /linux-4.4.14/Documentation/networking/mac80211_hwsim/ |
| D | README | 35 currently enabled and on the same channel as the transmitting
|
| /linux-4.4.14/Documentation/networking/caif/ |
| D | README | 105 might be problems transmitting over UART.
|
| D | Linux-CAIF.txt | 72 - When receiving / transmitting CAIF Packets (cfpkt), ownership is passed
|
| /linux-4.4.14/Documentation/serial/ |
| D | driver | 120 Stop transmitting characters. This might be due to the CTS
124 The driver should stop transmitting characters as soon as
132 Start transmitting characters.
|
| /linux-4.4.14/Documentation/ABI/testing/ |
| D | sysfs-class-net-cdc_ncm | 57 aggregate before transmitting an NTB frame.
|
| /linux-4.4.14/Documentation/i2c/ |
| D | fault-codes | 40 transmit mode: some other master was transmitting different
|
| /linux-4.4.14/Documentation/devicetree/bindings/mailbox/ |
| D | omap-mailbox.txt | 69 Cell #1 (fifo_id) - mailbox fifo id used either for transmitting
|
| /linux-4.4.14/Documentation/networking/ |
| D | scaling.txt | 368 which transmit queue to use when transmitting a packet on a multi-queue
383 When transmitting the first packet in a flow, the function
390 The queue chosen for transmitting a particular flow is saved in the
|
| D | PLIP.txt | 203 To start a transfer the transmitting machine outputs a nibble 0x08.
|
| D | e1000.txt | 145 greater than 75,000, may hang (stop transmitting) adapters
201 hang (stop transmitting) under certain network conditions. If
|
| D | lapb-module.txt | 174 Queue data with the LAPB module for transmitting over the link. If the call
|
| D | e1000e.txt | 140 hang (stop transmitting) under certain network conditions. If
|
| D | ixgbe.txt | 108 receiving and transmitting pause frames for ixgbe. When TX is enabled, PAUSE
|
| D | stmmac.txt | 54 Once the controller has finished transmitting the packet, napi will be
|
| D | rxrpc.txt | 902 The amount of time in milliseconds after transmitting a packet before we
|
| /linux-4.4.14/Documentation/usb/ |
| D | WUSB-Design-overview.txt | 61 UWB uses a band from roughly 3 to 10 GHz, transmitting at a max of
|
| /linux-4.4.14/Documentation/ |
| D | kernel-docs.txt | 460 socket, receiving, transmitting, forwarding, routing, packets,
|