Searched refs:resistance (Results 1 – 20 of 20) sorted by relevance
| /linux-4.4.14/Documentation/devicetree/bindings/hwmon/ |
| D | max6697.txt | 40 - resistance-cancellation
41 Boolean for all chips other than MAX6581. Set to enable resistance
43 For MAX6581, resistance cancellation enabled for all channels if
46 If not specified, resistance cancellation will be disabled for all
61 resistance-cancellation;
|
| /linux-4.4.14/Documentation/hwmon/ |
| D | ntc_thermistor | 26 that requires users to provide the resistance and lookup the corresponding
86 are suitable or the user can get the resistance directly, the user should
|
| D | vt1211 | 149 nominal resistance at 25C)
|
| /linux-4.4.14/Documentation/devicetree/bindings/input/touchscreen/ |
| D | ti-tsc-adc.txt | 8 ti,x-plate-resistance: X plate resistance
71 ti,x-plate-resistance = <200>;
|
| D | tsc2005.txt | 13 - ti,x-plate-ohms : integer, resistance of the touchscreen's X plates
|
| D | tsc2007.txt | 6 - ti,x-plate-ohms: X-plate resistance in ohms.
|
| /linux-4.4.14/Documentation/devicetree/bindings/power/ |
| D | qcom,coincell-charger.txt | 20 Definition: resistance (in ohms) for current-limiting resistor
|
| /linux-4.4.14/Documentation/devicetree/bindings/iio/adc/ |
| D | vf610-adc.txt | 22 source resistance (R_as) and capacitance (C_as). Refer the datasheet's
|
| /linux-4.4.14/Documentation/misc-devices/ |
| D | ad525x_dpot.txt | 6 work with the immediate resistance settings as well as update the saved startup
|
| /linux-4.4.14/Documentation/devicetree/bindings/mfd/ |
| D | twl6040.txt | 58 /* Vibra driver, motor resistance parameters */
|
| /linux-4.4.14/drivers/gpu/drm/msm/dsi/pll/ |
| D | dsi_pll_28nm.c | 53 u32 resistance; member
163 pll_write(base + REG_DSI_28nm_PHY_PLL_LPFR_CFG, lpfr_lut[i].resistance); in dsi_pll_28nm_clk_set_rate()
|
| /linux-4.4.14/arch/arm/boot/dts/ |
| D | sun8i-a23-evb.dts | 126 * The RX line has a non-populated resistance. In order to use it, you
|
| D | omap4-sdp.dts | 388 /* Vibra driver, motor resistance parameters */
|
| D | am335x-pepper.dts | 513 ti,x-plate-resistance = <200>;
|
| D | am335x-evmsk.dts | 707 ti,x-plate-resistance = <200>;
|
| D | am335x-evm.dts | 723 ti,x-plate-resistance = <200>;
|
| /linux-4.4.14/Documentation/video4linux/ |
| D | si476x.txt | 99 0x04 | fmagc1 | FMAGC1 attenuator resistance
|
| /linux-4.4.14/Documentation/devicetree/bindings/pinctrl/ |
| D | brcm,bcm11351-pinctrl.txt | 177 - setting pull-up resistance to 720 Ohm (ie. enabling 1.2k and 1.8k resistors
|
| /linux-4.4.14/Documentation/development-process/ |
| D | 6.Followthrough | 192 acceptable to you. There is a certain resistance to merging patches which
|
| /linux-4.4.14/Documentation/ABI/testing/ |
| D | sysfs-bus-iio | 1482 Raw (unscaled no offset etc.) resistance reading that can be processed
|