| /linux-4.4.14/drivers/net/ethernet/intel/fm10k/ |
| D | fm10k_mbx.c | 364 end = fm10k_fifo_head_offset(fifo, mbx->pulled); in fm10k_mbx_write_copy()
402 mbx->pulled += mbx->tail_len - ack; in fm10k_mbx_pull_head()
406 len = fm10k_fifo_used(fifo) - mbx->pulled; in fm10k_mbx_pull_head()
416 len && (mbx->pulled >= len); in fm10k_mbx_pull_head()
418 mbx->pulled -= fm10k_fifo_head_drop(fifo); in fm10k_mbx_pull_head()
633 head = fm10k_fifo_head_offset(&mbx->tx, mbx->pulled); in fm10k_mbx_update_local_crc()
874 crc = fm10k_fifo_crc(fifo, fm10k_fifo_head_offset(fifo, mbx->pulled), in fm10k_mbx_create_data_hdr()
1078 mbx->pulled += mbx->tail_len - ack; in fm10k_mbx_reset_work()
1081 while (fm10k_fifo_head_len(&mbx->tx) && mbx->pulled) { in fm10k_mbx_reset_work()
1084 if (mbx->pulled >= len) in fm10k_mbx_reset_work()
[all …]
|
| D | fm10k_mbx.h | 281 u16 tail, tail_len, pulled; member
|
| /linux-4.4.14/Documentation/devicetree/bindings/display/tilcdc/ |
| D | tfp410.txt | 10 - powerdn-gpio: the powerdown GPIO, pulled low to power down the
|
| /linux-4.4.14/arch/powerpc/boot/dts/fsl/ |
| D | p1023rdb.dts | 186 /* IRQ[0:3] are pulled up on board, set to active-low */
212 * IRQ[7] is pulled up on board, set to active-low
238 * IRQ[8:10] are pulled up on board, set to active-low
|
| /linux-4.4.14/Documentation/devicetree/bindings/leds/ |
| D | leds-ktd2692.txt | 10 Also, When the AUX pin is pulled high while CTRL pin is high,
|
| /linux-4.4.14/Documentation/devicetree/bindings/mfd/ |
| D | s2mps11.txt | 22 - samsung,s2mps11-wrstbi-ground: Indicates that WRSTBI pin of PMIC is pulled
27 register to turn off the power. Usually the ACOKB is pulled up to VBATT so
|
| D | tps6507x.txt | 29 0: If defdcdc pin of DCDC2/DCDC3 is pulled to GND.
|
| /linux-4.4.14/Documentation/fb/ |
| D | metronomefb.txt | 14 The display and error status are each pulled through individual GPIOs.
|
| /linux-4.4.14/arch/arm/boot/dts/ |
| D | sun4i-a10-pcduino2.dts | 47 * is controlled by the PD2 pin (pulled-up by default). Also one of
|
| D | imx6qdl-hummingboard.dtsi | 225 * pulled down for a fixed host connection.
|
| /linux-4.4.14/Documentation/development-process/ |
| D | 7.AdvancedTopics | 49 will, of course, need a server that can be pulled from. Setting up such a
81 have pulled into their repositories, you will make life much more difficult
115 can affect your ability to get trees pulled in the future. Quoting Linus:
|
| D | 6.Followthrough | 158 having a patch pulled as the result of a failure to fix a regression could
|
| /linux-4.4.14/Documentation/devicetree/bindings/usb/ |
| D | exynos-usb.txt | 25 needs to be pulled up for the bus to be powered.
|
| /linux-4.4.14/Documentation/devicetree/bindings/gpio/ |
| D | gpio-pcf857x.txt | 41 the input (pulled-up) state. When the bit is set to one, the line will be
|
| /linux-4.4.14/Documentation/scsi/ |
| D | lpfc.txt | 34 received from the midlayer. In the cases where a cable was pulled, link
|
| D | ChangeLog.sym53c8xx_2 | 33 - Check against GPIO3 pulled low for HVD controllers (driver did
|
| D | ncr53c8xx.txt | 1193 you must ensure that lines of the wide part of the SCSI BUS are pulled-up.
1819 BigLit to be pulled-up. Using this mode, most of byte reorderings should
|
| D | ChangeLog.lpfc | 351 * Ensure that scsi_transport_fc.h is always pulled in by
|
| /linux-4.4.14/Documentation/power/ |
| D | charger-manager.txt | 194 At the charger/battery-related events such as battery-pulled-out,
195 charger-pulled-out, charger-inserted, DCIN-over/under-voltage, charger-stopped,
|
| /linux-4.4.14/Documentation/arm/nwfpe/ |
| D | TODO | 55 [NOTE: pulled out from some docs on ARM floating point, specifically
|
| /linux-4.4.14/Documentation/networking/ |
| D | netdev-FAQ.txt | 53 the "net" tree will start accumulating fixes for this pulled content
|
| /linux-4.4.14/Documentation/isdn/ |
| D | INTERFACE | 83 already have its private data pulled off the head of the sk_buff.
|
| /linux-4.4.14/Documentation/PCI/ |
| D | pci.txt | 103 pulled out of a hot-pluggable slot).
|
| /linux-4.4.14/drivers/scsi/aic7xxx/ |
| D | aic7xxx.seq | 55 * SCB that we've already pulled from the QINFIFO and started the selection
1964 * using SCSIBUSL. When we have pulled the ATN line, or we just want to
|
| D | aic79xx.seq | 1423 * byte directly off the bus using SCSIBUSL. When we have pulled the ATN
|
| /linux-4.4.14/Documentation/ |
| D | HOWTO | 325 pulled on an almost daily basis:
|
| D | SubmittingPatches | 139 form which can be easily pulled into Linux's source code management
|