| /linux-4.4.14/arch/x86/platform/ts5500/ |
| H A D | ts5500.c | 14 * (SBC) and its devices, and exposes information to userspace such as jumpers'
77 * @jumpers: Bitfield for jumpers' state.
87 u8 jumpers; member in struct:ts5500_sbc
149 sbc->jumpers = tmp & ~TS5500_LED; ts5500_detect_config()
179 return sprintf(buf, "0x%.2x\n", sbc->jumpers >> 1); jumpers_show()
181 static DEVICE_ATTR_RO(jumpers);
|
| /linux-4.4.14/drivers/staging/comedi/drivers/ |
| H A D | pcmad.c | 32 * [2] - Analog input reference (must match jumpers)
35 * [3] - Analog input encoding (must match jumpers)
|
| H A D | ni_labpc.c | 33 * will depend on how you have configured the jumpers on your board
|
| H A D | pcmda12.c | 54 /* AI range is not configurable, it's set by jumpers on the board */
|
| H A D | adq12b.c | 33 * [0] - I/O base address (set with hardware jumpers)
|
| H A D | dt2814.c | 31 clock is selected by jumpers, and the clock divider can be selected
|
| H A D | ii_pci20kc.c | 118 /* the AO range is set by jumpers on the 20006M module */
|
| H A D | ni_at_ao.c | 31 * [3] - analog output range, set by jumpers on hardware
|
| H A D | pcl711.c | 161 * jumpers on the board. pcl711_ai_set_mode()
|
| H A D | amplc_pci224.c | 74 * LK1 which affects all channels, and jumpers LK2, LK3, LK4 and LK5
305 * and jumpers LK2, LK3, LK4 and LK5 affecting channels 0, 1, 2 and 3
|
| H A D | dt282x.c | 171 * The Analog Output range is set per-channel using jumpers on the board.
1160 /* ranges are per-channel, set by jumpers on the board */ dt282x_attach()
|
| H A D | pcmuio.c | 36 * are done through jumpers on the board. You need to pass that information
|
| /linux-4.4.14/drivers/net/can/sja1000/ |
| H A D | tscan1.c | 57 /* PLD jumpers register bits */
|
| /linux-4.4.14/sound/oss/ |
| H A D | aedsp16.c | 43 It is software-only configurable (no jumpers to hard-set irq/dma/mpu-irq),
98 them with jumpers. For SC-6600 cards you have no jumpers so you have
102 your computer and massage the jumpers (there are no irq/dma/mirq
103 jumpers to be configured anyway, only I/O BASE values have to be
104 configured with jumpers)
|
| /linux-4.4.14/drivers/watchdog/ |
| H A D | acquirewdt.c | 47 * The Watch-Dog Timer Time-Out Period is set via jumpers.
|
| /linux-4.4.14/drivers/scsi/ |
| H A D | pas16.c | 99 * irq jumpers on the board). The first value in the array will be
|
| /linux-4.4.14/sound/isa/ |
| H A D | cmi8328.c | 33 /* I/O port is configured by jumpers on the card to one of these */
|
| /linux-4.4.14/drivers/ata/ |
| H A D | pata_legacy.c | 52 * Use the jumpers, autospeed and set pio_mask to the mode on the jumpers with
|
| /linux-4.4.14/drivers/net/appletalk/ |
| H A D | ltpc.c | 166 /* ltpc jumpers are:
|
| /linux-4.4.14/arch/arm/common/ |
| H A D | sa1111.c | 1392 * User's Guide" mentions that jumpers R51 and R52 control the sa1111_needs_bounce()
|
| /linux-4.4.14/drivers/net/ethernet/packetengines/ |
| H A D | yellowfin.c | 143 PCI bus devices are configured by the system at boot time, so no jumpers
|
| H A D | hamachi.c | 220 No jumpers exist on the board. The chip supports software correction of
|
| /linux-4.4.14/drivers/net/ethernet/smsc/ |
| H A D | epic100.c | 122 PCI bus devices are configured by the system at boot time, so no jumpers
|
| /linux-4.4.14/drivers/net/wan/ |
| H A D | dscc4.c | 34 * remove the jumpers. The operation is described on Etinc web site. If you
|
| /linux-4.4.14/drivers/isdn/hardware/mISDN/ |
| H A D | hfcmulti.c | 5203 /* Port mode (TE/NT) jumpers */ hfcmulti_init()
5209 printk(KERN_INFO "%s: %s DIPs(0x%x) jumpers(0x%x)\n", hfcmulti_init()
|
| /linux-4.4.14/drivers/net/ethernet/3com/ |
| H A D | 3c59x.c | 147 PCI bus devices are configured by the system at boot time, so no jumpers
|