Searched refs:gear (Results 1 – 10 of 10) sorted by relevance
| /linux-4.4.14/drivers/scsi/ufs/ |
| D | ufs-qcom.c | 354 static int ufs_qcom_cfg_timers(struct ufs_hba *hba, u32 gear, in ufs_qcom_cfg_timers() argument
394 if (gear == 0) { in ufs_qcom_cfg_timers()
395 dev_err(hba->dev, "%s: invalid gear = %d\n", __func__, gear); in ufs_qcom_cfg_timers()
429 if (gear > ARRAY_SIZE(hs_fr_table_rA)) { in ufs_qcom_cfg_timers()
432 __func__, gear, in ufs_qcom_cfg_timers()
436 tx_clk_cycles_per_us = hs_fr_table_rA[gear-1][1]; in ufs_qcom_cfg_timers()
438 if (gear > ARRAY_SIZE(hs_fr_table_rB)) { in ufs_qcom_cfg_timers()
441 __func__, gear, in ufs_qcom_cfg_timers()
445 tx_clk_cycles_per_us = hs_fr_table_rB[gear-1][1]; in ufs_qcom_cfg_timers()
454 if (gear > ARRAY_SIZE(pwm_fr_table)) { in ufs_qcom_cfg_timers()
[all …]
|
| /linux-4.4.14/drivers/media/i2c/ |
| D | ad9389b.c | 282 u8 gear; in ad9389b_set_manual_pll_gear() local
298 gear = 0xc0; /* 4th gear */ in ad9389b_set_manual_pll_gear()
300 gear = 0xb0; /* 3rd gear */ in ad9389b_set_manual_pll_gear()
302 gear = 0xa0; /* 2nd gear */ in ad9389b_set_manual_pll_gear()
304 gear = 0x90; /* 1st gear */ in ad9389b_set_manual_pll_gear()
306 gear = 0x80; /* 0th gear */ in ad9389b_set_manual_pll_gear()
308 ad9389b_wr_and_or(sd, 0x98, 0x0f, gear); in ad9389b_set_manual_pll_gear()
|
| /linux-4.4.14/Documentation/devicetree/bindings/hwmon/ |
| D | g762.txt | 18 - "fan_gear_mode": fan gear mode. Supported values are 0, 1 and 2.
|
| /linux-4.4.14/Documentation/hwmon/ |
| D | g762 | 35 fan1_fault: reports fan failure, i.e. no transition on fan gear pin for
|
| /linux-4.4.14/arch/m32r/platforms/m32700ut/ |
| D | dot.gdbinit_400MHz_32MB | 22 # and switch off PLL, before resetting the clock gear ratio.
|
| D | dot.gdbinit_200MHz_16MB | 22 # and switch off PLL, before resetting the clock gear ratio.
|
| D | dot.gdbinit_300MHz_32MB | 22 # and switch off PLL, before resetting the clock gear ratio.
|
| /linux-4.4.14/Documentation/blockdev/ |
| D | cciss.txt | 155 kicks into gear whenever a SCSI command fails to complete within a
|
| /linux-4.4.14/Documentation/networking/ |
| D | vortex.txt | 274 but this has to be viewed as a workaround for broken network gear and
|
| /linux-4.4.14/Documentation/usb/ |
| D | WUSB-Design-overview.txt | 125 their type and kick into gear.
|