| /linux-4.4.14/drivers/infiniband/ulp/ipoib/ |
| D | ipoib_ethtool.c | 67 coal->rx_coalesce_usecs = priv->ethtool.coalesce_usecs; in ipoib_get_coalesce()
68 coal->rx_max_coalesced_frames = priv->ethtool.max_coalesced_frames; in ipoib_get_coalesce()
94 priv->ethtool.coalesce_usecs = coal->rx_coalesce_usecs; in ipoib_set_coalesce()
95 priv->ethtool.max_coalesced_frames = coal->rx_max_coalesced_frames; in ipoib_set_coalesce()
|
| D | ipoib.h | 391 struct ipoib_ethtool_st ethtool; member
|
| /linux-4.4.14/Documentation/networking/ |
| D | e100.txt | 63 ethtool -G eth? rx n, where n is the number of desired rx descriptors.
72 ethtool -G eth? tx n, where n is the number of desired tx descriptors.
75 default. The ethtool utility can be used as follows to force speed/duplex.
77 ethtool -s eth? autoneg off speed {10|100} duplex {full|half}
86 ethtool -s eth? msglvl n
125 ethtool
128 The driver utilizes the ethtool interface for driver configuration and
129 diagnostics, as well as displaying statistical information. The ethtool
132 The latest release of ethtool can be found from
133 http://ftp.kernel.org/pub/software/network/ethtool/
[all …]
|
| D | gianfar.txt | 14 packets. Use ethtool to enable or disable this feature for RX
40 The gianfar driver supports the use of ethtool for many
41 configuration options. You must run ethtool only on currently
42 open interfaces. See ethtool documentation for details.
|
| D | igb.txt | 60 ethtool
62 The driver utilizes the ethtool interface for driver configuration and
64 version of ethtool can be found at:
66 http://ftp.kernel.org/pub/software/network/ethtool/
70 WoL is configured through the ethtool* utility.
72 For instructions on enabling WoL with ethtool, refer to the ethtool man page.
|
| D | igbvf.txt | 33 Instructions on updating ethtool can be found in the section "Additional
58 ethtool
60 The driver utilizes the ethtool interface for driver configuration and
61 diagnostics, as well as displaying statistical information. The ethtool
65 http://ftp.kernel.org/pub/software/network/ethtool/
|
| D | s2io.txt | 36 To associate an interface with a physical adapter use "ethtool -p <ethX>".
56 using "ethtool -S" option.
115 b. Ensure Transmit Checksum offload is enabled. Use ethtool to set/verify this
117 c. Turn on TSO(using "ethtool -K")
118 # ethtool -K <ethX> tso on
127 c. Ensure Receive Checksum offload is enabled. Use "ethtool -K ethX" command to
|
| D | cxgb.txt | 38 The interface used to control this feature is ethtool. Please see the
39 ethtool manpage for additional usage information.
44 ethtool -C <interface> adaptive-rx on
46 To disable adaptive-rx, use ethtool:
48 ethtool -C <interface> adaptive-rx off
53 ethtool -C <interface> rx-usecs <microseconds>
57 ethtool -C eth0 rx-usecs 100
61 ethtool -C <interface> adaptive-rx off rx-usecs <microseconds>
69 ethtool -c <interface>
79 The interface used to control this feature is ethtool version 1.8 or higher.
[all …]
|
| D | ixgbe.txt | 38 the same Speed setting via ethtool. Results may vary if you mix speed settings.
107 Ethernet Flow Control (IEEE 802.3x) can be configured with ethtool to enable
114 capable link partner, use ethtool:
116 ethtool -A eth? autoneg off RX off TX off
135 in ethtool: fdir_miss and fdir_match.
137 Other ethtool Commands:
139 ethtool -K ethX ntuple on
141 Use -U switch. e.g., ethtool -U ethX flow-type tcp4 src-ip 10.0.128.23
144 ethtool -u ethX
153 To account for filter matches and misses, there are two stats in ethtool:
[all …]
|
| D | i40e.txt | 59 The driver utilizes the ethtool interface for driver configuration and
61 ethtool version is required for this functionality.
63 The latest release of ethtool can be found from
64 https://www.kernel.org/pub/software/network/ethtool
|
| D | e1000e.txt | 271 ethtool
273 The driver utilizes the ethtool interface for driver configuration and
275 strongly recommend downloading the latest version of ethtool at:
277 http://ftp.kernel.org/pub/software/network/ethtool/
280 you need to add a few seconds between tests when working with ethtool.
284 Speed and Duplex are configured through the ethtool* utility. For
285 instructions, refer to the ethtool man page.
289 WoL is configured through the ethtool* utility. For instructions on
290 enabling WoL with ethtool, refer to the ethtool man page.
297 adapters. To verify if a port supports Wake on Lan run ethtool eth<X>.
|
| D | ixgb.txt | 41 supported in this release. Alternatively, you can use ethtool (version 1.6
44 Instructions on updating ethtool can be found in the section "Additional
309 ethtool
311 The driver utilizes the ethtool interface for driver configuration and
312 diagnostics, as well as displaying statistical information. The ethtool
315 The latest release of ethtool can be found from
316 http://ftp.kernel.org/pub/software/network/ethtool/
318 NOTE: The ethtool version 1.6 only supports a limited set of ethtool options.
319 Support for a more complete ethtool feature set can be enabled by
417 "ethtool -K eth0 tso off" may resolve the problem.
|
| D | stmmac.txt | 71 Mitigation parameters can be tuned by ethtool.
103 # ethtool -S ethX command
278 o stmmac_ethtool.c: to implement the ethtool support;
306 For example a user can be use the ethtool support
307 to get statistics: e.g. using: ethtool -S ethX
309 or sees the MAC/DMA registers: e.g. using: ethtool -d ethX
|
| D | altera_tse.txt | 89 ethtool -S ethX command. It is possible to dump registers etc.
98 o altera_tse_ethtool.c: ethtool support
114 A user may use the ethtool support to get statistics:
115 e.g. using: ethtool -S ethX (that shows the statistics counters)
116 or sees the MAC registers: e.g. using: ethtool -d ethX
|
| D | dm9000.txt | 163 ethtool
166 The driver supports the ethtool interface for access to the driver
|
| D | e1000.txt | 431 ethtool
433 The driver utilizes the ethtool interface for driver configuration and
434 diagnostics, as well as displaying statistical information. The ethtool
437 The latest release of ethtool can be found from
438 http://ftp.kernel.org/pub/software/network/ethtool/
442 WoL is configured through the ethtool* utility.
|
| D | vxge.txt | 61 "ethtool -S" option.
|
| D | pktgen.txt | 32 # ethtool -G ethX tx 1024
46 and the cleanup interval is affected by the ethtool --coalesce setting
50 # ethtool -C ethX rx-usecs 30
|
| D | batman-adv.txt | 170 batman-adv module are available through ethtool:
172 # ethtool --statistics bat0
|
| D | 3c509.txt | 80 Full-duplex mode can be enabled using 'ethtool'.
118 The transceiver type can be changed using 'ethtool'.
|
| D | scaling.txt | 46 be configured from ethtool (--config-ntuple).
61 indirection table can be retrieved and modified at runtime using ethtool
354 It also requires that ntuple filtering is enabled via ethtool. The map
|
| D | phy.txt | 129 mask off SUPPORTED_1000baseT*). See include/linux/ethtool.h for definitions
|
| D | switchdev.txt | 80 standard netdev tools (iproute2, ethtool, etc), the port netdev can also
|
| D | bonding.txt | 1919 querying the device's MII registers, or by making an ethtool query to
1933 monitor will make an ethtool ETHOOL_GLINK request to attempt to obtain
1936 and ethtool requests), then the MII monitor will assume the link is
2411 interface, this mode requires certain ethtool support in the
|
| /linux-4.4.14/drivers/staging/slicoss/ |
| D | TODO | 18 use ethtool instead
22 - do ethtool correctly using ethtool_ops
|
| /linux-4.4.14/drivers/net/ethernet/atheros/alx/ |
| D | Makefile | 2 alx-objs := main.o ethtool.o hw.o
|
| /linux-4.4.14/drivers/net/ethernet/intel/ixgbevf/ |
| D | Makefile | 36 ethtool.o \
|
| /linux-4.4.14/drivers/net/ethernet/intel/igbvf/ |
| D | Makefile | 36 ethtool.o \
|
| /linux-4.4.14/drivers/net/ethernet/neterion/vxge/ |
| D | Makefile | 7 vxge-objs := vxge-config.o vxge-traffic.o vxge-ethtool.o vxge-main.o
|
| /linux-4.4.14/drivers/net/ethernet/intel/e1000e/ |
| D | Makefile | 36 param.o ethtool.o netdev.o ptp.o
|
| /linux-4.4.14/drivers/net/ethernet/amd/xgbe/ |
| D | Makefile | 4 xgbe-desc.o xgbe-ethtool.o xgbe-mdio.o \
|
| /linux-4.4.14/drivers/net/ethernet/sfc/ |
| D | Makefile | 2 rx.o selftest.o ethtool.o qt202x_phy.o mdio_10g.o \
|
| /linux-4.4.14/Documentation/networking/dsa/ |
| D | dsa.txt | 150 - query the switch for ethtool operations: statistics, link state,
156 stack/ethtool, and the switch driver implementation.
265 - inability to fetch switch CPU port statistics counters using ethtool, which
439 - get_strings: ethtool function used to query the driver's strings, will
442 - get_ethtool_stats: ethtool function used to query per-port statistics and
447 - get_sset_count: ethtool function used to query the number of statistics items
449 - get_wol: ethtool function used to obtain Wake-on-LAN settings per-port, this
453 - set_wol: ethtool function used to configure Wake-on-LAN settings per-port,
456 - set_eee: ethtool function which is used to configure a switch port EEE (Green
461 - get_eee: ethtool function which is used to query a switch port EEE settings,
[all …]
|
| /linux-4.4.14/drivers/net/wireless/ath/wil6210/ |
| D | Makefile | 19 wil6210-y += ethtool.o
|
| /linux-4.4.14/drivers/net/wireless/libertas/ |
| D | Makefile | 5 libertas-y += ethtool.o
|
| D | README | 37 # ethtool -i eth0
46 ethtool -e ethX [raw on|off] [offset N] [length N]
54 # ethtool -e eth0 offset 0 length 16
231 "ethtool -s ethX wol X" command before enabling host sleep.
|
| /linux-4.4.14/net/core/ |
| D | Makefile | 10 obj-y += dev.o ethtool.o dev_addr_lists.o dst.o netevent.o \
|
| /linux-4.4.14/drivers/net/wireless/mwifiex/ |
| D | Makefile | 42 mwifiex-y += ethtool.o
|
| /linux-4.4.14/net/wireless/ |
| D | Makefile | 13 cfg80211-y += mlme.o ibss.o sme.o chan.o ethtool.o mesh.o ap.o trace.o ocb.o
|
| /linux-4.4.14/net/mac80211/ |
| D | Makefile | 23 ethtool.o \
|
| /linux-4.4.14/Documentation/infiniband/ |
| D | ipoib.txt | 60 on/off using ethtool calls. Currently LRO is supported only for
68 use ethtool to set interrupt mitigation parameters and thus reduce
|
| /linux-4.4.14/Documentation/ABI/testing/ |
| D | sysfs-class-net | 120 the ethtool get_settings method (mostly Ethernet).
227 the ethtool get_settings method (mostly Ethernet ).
|
| /linux-4.4.14/Documentation/devicetree/bindings/net/ |
| D | cpsw.txt | 23 ethtool and SIOCGMIIPHY
|
| /linux-4.4.14/Documentation/DocBook/ |
| D | networking.xml.db | 433 API-phy-ethtool-sset
444 API-phy-ethtool-get-eee
445 API-phy-ethtool-set-eee
|
| /linux-4.4.14/drivers/net/ethernet/marvell/ |
| D | Kconfig | 82 with better performance and more complete ethtool support.
|
| /linux-4.4.14/Documentation/sysctl/ |
| D | net.txt | 161 provide ethtool -x support yet.
171 myhost:~# ethtool -x eth0
|
| /linux-4.4.14/drivers/net/wireless/ |
| D | Kconfig | 147 micro support for ethtool.
|
| /linux-4.4.14/include/uapi/linux/ |
| D | Kbuild | 116 header-y += ethtool.h
|
| /linux-4.4.14/Documentation/power/ |
| D | devices.txt | 38 drivers the ioctl interface used by ethtool may also be used for this
181 ethtool. It should also default to "enabled" for devices that don't generate
|