| /linux-4.4.14/drivers/pinctrl/ |
| D | pinctrl-lpc18xx.c | 254 LPC_P(2,5, SGPIO, CTIN, USB1, ADCTRIG, GPIO, R, TIMER3, USB0, 0, HD);
264 LPC_P(3,1, I2S0_TX_WS, I2S0_RX_WS,CAN0,USB1,GPIO, R, LCD, R, 0, ND);
265 LPC_P(3,2, I2S0_TX_SDA, I2S0_RX_SDA,CAN0,USB1,GPIO, R, LCD, R, 0, ND);
315 LPC_P(8,3, GPIO, USB1, R, LCD, LCD_ALT, R, R, TIMER0, 0, ND);
316 LPC_P(8,4, GPIO, USB1, R, LCD, LCD_ALT, R, R, TIMER0, 0, ND);
317 LPC_P(8,5, GPIO, USB1, R, LCD, LCD_ALT, R, R, TIMER0, 0, ND);
318 LPC_P(8,6, GPIO, USB1, R, LCD, LCD_ALT, R, R, TIMER0, 0, ND);
319 LPC_P(8,7, GPIO, USB1, R, LCD, LCD_ALT, R, R, TIMER0, 0, ND);
320 LPC_P(8,8, R, USB1, R, R, R, R,CGU_OUT, I2S1, 0, ND);
324 LPC_P(9,3, GPIO, MCTRL, USB1, R, R, ENET, SGPIO, UART3, 0, ND);
[all …]
|
| /linux-4.4.14/drivers/media/usb/b2c2/ |
| D | Kconfig | 5 Support for the Air/Sky/Cable2PC USB1.1 box (DVB/ATSC) by Technisat/B2C2,
|
| /linux-4.4.14/Documentation/dvb/ |
| D | README.dvb-usb | 65 2005-01-31 - distorted streaming is gone for USB1.1 devices
172 2.2. USB1.1 Bandwidth limitation
174 A lot of the currently supported devices are USB1.1 and thus they have a
180 frequency simply does not work very well. This applies to all USB1.1
|
| /linux-4.4.14/Documentation/devicetree/bindings/reset/ |
| D | nxp,lpc1850-rgu.txt | 24 18 USB1
|
| /linux-4.4.14/arch/sh/kernel/cpu/sh4a/ |
| D | setup-sh7724.c | 882 USB0, USB1, enumerator
945 INTC_VECT(USB1, 0xA40),
1022 INTC_GROUP(USB, USB0, USB1),
1060 { 0, 0, 0, CMT, 0, USB1, USB0, 0 } },
|
| D | setup-sh7757.c | 803 USB0, USB1, enumerator
869 INTC_VECT(USB1, 0x920),
978 IRQ9, IRQ8, SCIF1, SCIF0, USB0, 0, 0, USB1,
1078 { INT2PRI12, 0, 32, 8, { USB0, 0, IRQ15, USB1 } },
|
| /linux-4.4.14/arch/powerpc/boot/dts/ |
| D | pdm360ng.dts | 130 /* USB1 using external ULPI PHY */
|
| D | mpc5125twr.dts | 232 // disable USB1 port
|
| D | sequoia.dts | 148 USB1: usb@e0000400 { label
|
| D | mpc5121.dtsi | 296 /* USB1 using external ULPI PHY */
|
| D | canyonlands.dts | 173 USB1: usb@bffd0000 { label
|
| /linux-4.4.14/drivers/media/usb/dvb-usb/ |
| D | Kconfig | 6 USB1.1 and USB2.0 DVB devices.
235 tristate "Afatech AF9005 DVB-T USB1.1 support"
240 Say Y here to support the Afatech AF9005 based DVB-T USB1.1 receiver
|
| /linux-4.4.14/arch/arm/boot/dts/ |
| D | sun8i-a33-sinlinx-sina33.dts | 145 usb1_vbus-supply = <®_vcc5v0>; /* USB1 VBUS is always on */
|
| D | sun4i-a10-pcduino.dts | 236 usb1_vbus-supply = <®_vcc5v0>; /* USB1 VBUS is always on */
|
| D | dove-cm-a510.dtsi | 67 * U4: 2 additional USB2.0 host ports (via USB1)
|
| D | am335x-pepper.dts | 594 /* USB1 Over-Current (active low) */
|
| /linux-4.4.14/Documentation/devicetree/bindings/clock/ |
| D | lpc1850-cgu.txt | 49 3 BASE_USB1_CLK Base clock for USB1
|
| /linux-4.4.14/drivers/media/usb/dvb-usb-v2/ |
| D | Kconfig | 6 USB1.1 and USB2.0 DVB devices.
|
| /linux-4.4.14/drivers/regulator/ |
| D | mc13892-regulator.c | 297 MC13892_FIXED_DEFINE(VUSB, USB1, mc13892_vusb),
|
| /linux-4.4.14/drivers/clk/nxp/ |
| D | clk-lpc18xx-cgu.c | 225 LPC1XX_CGU_BASE_CLK(USB1, base_all_src_ids, 0),
|