Home
last modified time | relevance | path

Searched refs:INIT_ZONE (Results 1 – 7 of 7) sorted by relevance

/linux-4.4.14/drivers/net/wireless/rsi/
Drsi_91x_sdio_ops.c39 rsi_dbg(INIT_ZONE, in rsi_sdio_master_access_msword()
55 rsi_dbg(INIT_ZONE, "%s:MASTER_ACCESS_LSBYTE:0x%x\n", __func__, byte); in rsi_sdio_master_access_msword()
107 rsi_dbg(INIT_ZONE, "%s: loading block: %d\n", __func__, ii); in rsi_copy_to_card()
132 rsi_dbg(INIT_ZONE, in rsi_copy_to_card()
155 rsi_dbg(INIT_ZONE, "%s: loaded firmware\n", __func__); in rsi_copy_to_card()
217 rsi_dbg(INIT_ZONE, "%s: Instruction size:%d\n", __func__, len); in rsi_load_ta_instructions()
218 rsi_dbg(INIT_ZONE, "%s: num blocks: %d\n", __func__, num_blocks); in rsi_load_ta_instructions()
307 rsi_dbg(INIT_ZONE, "%s: Enabling SDIO High speed\n", __func__); in rsi_init_sdio_slave_regs()
323 rsi_dbg(INIT_ZONE, "%s: Initialzing SDIO read start level\n", __func__); in rsi_init_sdio_slave_regs()
336 rsi_dbg(INIT_ZONE, "%s: Initialzing FIFO ctrl registers\n", __func__); in rsi_init_sdio_slave_regs()
[all …]
Drsi_91x_usb_ops.c58 rsi_dbg(INIT_ZONE, "%s: loading block: %d\n", __func__, ii); in rsi_copy_to_card()
74 rsi_dbg(INIT_ZONE, in rsi_copy_to_card()
78 rsi_dbg(INIT_ZONE, "%s: loaded firmware\n", __func__); in rsi_copy_to_card()
162 rsi_dbg(INIT_ZONE, "%s: Instruction size:%d\n", __func__, len); in rsi_load_ta_instructions()
163 rsi_dbg(INIT_ZONE, "%s: num blocks: %d\n", __func__, num_blocks); in rsi_load_ta_instructions()
Drsi_91x_sdio.c364 rsi_dbg(INIT_ZONE, "%s: Setting the block length\n", __func__); in rsi_setblocklength()
657 rsi_dbg(INIT_ZONE, "%s: Enabled the interface\n", __func__); in rsi_init_sdio_interface()
670 rsi_dbg(INIT_ZONE, "%s: Setup card succesfully\n", __func__); in rsi_init_sdio_interface()
708 rsi_dbg(INIT_ZONE, "%s: Init function called\n", __func__); in rsi_probe()
739 rsi_dbg(INIT_ZONE, "%s: Registered Interrupt handler\n", __func__); in rsi_probe()
826 rsi_dbg(INIT_ZONE, "%s: Registering driver\n", __func__); in rsi_module_init()
Drsi_91x_main.c272 rsi_dbg(INIT_ZONE, "%s: Module init called\n", __func__); in rsi_91x_hal_module_init()
286 rsi_dbg(INIT_ZONE, "%s: Module exit called\n", __func__); in rsi_91x_hal_module_exit()
Drsi_91x_usb.c433 rsi_dbg(INIT_ZONE, "%s: Enabled the interface\n", __func__); in rsi_init_usb_interface()
462 rsi_dbg(INIT_ZONE, "%s: Init function called\n", __func__); in rsi_probe()
501 rsi_dbg(INIT_ZONE, "%s: Performed device init\n", __func__); in rsi_probe()
Drsi_main.h26 #define INIT_ZONE BIT(2) /* For Driver Init Seq Msgs */ macro
Drsi_91x_mac80211.c1052 rsi_dbg(INIT_ZONE, "%s: Performing mac80211 attach\n", __func__); in rsi_mac80211_attach()