Searched refs:bidirectional (Results 1 – 22 of 22) sorted by relevance
| /linux-4.1.27/drivers/parport/ |
| D | TODO-parport | 18 4. A better PLIP (make use of bidirectional/ECP/EPP ports).
|
| D | Kconfig | 138 This driver provides support for the bidirectional parallel port
|
| /linux-4.1.27/net/dccp/ |
| D | Kconfig | 10 protocol that implements bidirectional, unicast connections of
|
| /linux-4.1.27/drivers/net/plip/ |
| D | Kconfig | 21 bidirectional parallel ports only, which can transmit 8 bits at a
|
| /linux-4.1.27/Documentation/gpio/ |
| D | gpio.txt | 50 cases (to support bidirectional signaling). GPIO controllers may have
97 Also, bidirectional data bus signals sometimes use open drain signals.
|
| D | gpio-legacy.txt | 37 cases (to support bidirectional signaling). GPIO controllers may have
421 Also, bidirectional data bus signals sometimes use open drain signals.
|
| /linux-4.1.27/Documentation/devicetree/bindings/gpio/ |
| D | gpio-pcf857x.txt | 3 The PCF857x-compatible chips have "quasi-bidirectional" I/O lines that can be
|
| /linux-4.1.27/block/ |
| D | Kconfig | 59 with bidirectional data transfers and generic request/response
|
| /linux-4.1.27/Documentation/devicetree/bindings/dma/ |
| D | ste-dma40.txt | 60 bidirectional, i.e. the same for RX and TX operations:
|
| /linux-4.1.27/drivers/input/joystick/ |
| D | db9.c | 99 int bidirectional; member
581 if (db9_mode->bidirectional && !(pp->modes & PARPORT_MODE_TRISTATE)) { in db9_probe()
|
| /linux-4.1.27/Documentation/devicetree/bindings/pinctrl/ |
| D | qcom,pmic-mpp.txt | 96 Valid values are 600, 10000 and 30000 in bidirectional mode
|
| /linux-4.1.27/Documentation/ |
| D | xillybus.txt | 138 A device file can be read only, write only or bidirectional. Bidirectional
225 device file. If the device file is bidirectional, and already opened only in
260 Each of the (possibly bidirectional) pipes presented to the user is allocated
|
| D | parport.txt | 155 TRISTATE Port is bidirectional.
|
| D | DMA-API.txt | 258 you must always sync bidirectional memory twice: once before the
|
| D | devices.txt | 3345 of a bidirectional pipe with TTY capabilities.
|
| /linux-4.1.27/Documentation/scsi/ |
| D | osd.txt | 152 A block device request can carry bidirectional payload by means of associating
|
| /linux-4.1.27/Documentation/i2c/ |
| D | slave-interface | 55 read/written and is thus bidirectional. The pointer to val must always be
|
| /linux-4.1.27/Documentation/target/ |
| D | tcmu-design.txt | 154 buffers. For bidirectional commands, iov_cnt specifies how many iovec
|
| /linux-4.1.27/Documentation/input/ |
| D | joystick-parport.txt | 481 Caveat here: This driver only works on bidirectional parallel ports. If
|
| /linux-4.1.27/Documentation/blockdev/ |
| D | paride.txt | 321 in EPP mode, try to use "bidirectional" or "PS/2" mode and 1x speeds only.
|
| /linux-4.1.27/drivers/gpio/ |
| D | Kconfig | 618 Say yes here to provide access to most "quasi-bidirectional" I2C
|
| /linux-4.1.27/Documentation/spi/ |
| D | spi-summary | 385 + when bidirectional reads and writes start ... by how its
|