| /linux-4.1.27/drivers/gpu/drm/via/ |
| D | via_dmablit.c | 334 done_transfer = done_transfer || (blitq->aborting && !(status & VIA_DMA_CSR_DE)); in via_dmablit_handler()
339 blitq->blits[cur]->aborted = blitq->aborting; in via_dmablit_handler()
355 blitq->aborting = 0; in via_dmablit_handler()
365 blitq->aborting = 1; in via_dmablit_handler()
561 blitq->aborting = 0; in via_init_dmablit()
|
| D | via_dmablit.h | 71 int aborting; member
|
| /linux-4.1.27/drivers/i2c/busses/ |
| D | i2c-mv64xxx.c | 124 u32 aborting; member
257 || (drv_data->aborting in mv64xxx_i2c_fsm()
259 if (drv_data->send_stop || drv_data->aborting) { in mv64xxx_i2c_fsm()
301 if ((drv_data->bytes_left == 1) || drv_data->aborting) in mv64xxx_i2c_fsm()
336 drv_data->aborting = 0; in mv64xxx_i2c_send_start()
552 drv_data->aborting = 1; in mv64xxx_i2c_wait_for_completion()
|
| /linux-4.1.27/drivers/nfc/ |
| D | trf7970a.c | 433 bool aborting; member
611 if (trf->rx_skb && !IS_ERR(trf->rx_skb) && !trf->aborting) in trf7970a_send_upstream()
618 if (trf->aborting) { in trf7970a_send_upstream()
626 trf->aborting = false; in trf7970a_send_upstream()
1084 trf->aborting = false; in trf7970a_switch_rf_off()
1467 if (trf->aborting) { in trf7970a_send_cmd()
1469 trf->aborting = false; in trf7970a_send_cmd()
1710 if (trf->aborting) { in _trf7970a_tg_listen()
1712 trf->aborting = false; in _trf7970a_tg_listen()
1826 trf->aborting = true; in trf7970a_abort_cmd()
|
| /linux-4.1.27/drivers/scsi/arm/ |
| D | fas216.h | 253 unsigned char aborting:1; /* aborting command */ member
|
| D | fas216.c | 204 info->scsi.disconnectable, info->scsi.aborting); in fas216_dumpinfo()
915 info->scsi.aborting = 0; in fas216_disconnect_intr()
1031 info->scsi.aborting = 1; in fas216_reselected_intr()
1517 info->scsi.aborting = 1; in fas216_busservice_intr()
2147 if (info->scsi.aborting) { in fas216_done()
2150 info->scsi.aborting = 0; in fas216_done()
2806 info->scsi.aborting = 0; in fas216_reset_state()
|
| /linux-4.1.27/drivers/media/platform/ |
| D | sh_veu.c | 125 bool aborting; member
242 veu->aborting = true; in sh_veu_job_abort()
825 veu->aborting = false; in sh_veu_streamon()
1072 if (veu->xaction == MEM2MEM_DEF_TRANSLEN || veu->aborting) { in sh_veu_bh()
|
| D | mx2_emmaprp.c | 220 int aborting; member
247 ctx->aborting = 1; in emmaprp_job_abort()
369 if (!curr_ctx->aborting) { in emmaprp_irq()
|
| D | vim2m.c | 171 int aborting; member
367 ctx->aborting = 1; in job_abort()
416 || curr_ctx->aborting) { in device_isr()
|
| D | m2m-deinterlace.c | 146 int aborting; member
178 ctx->aborting = 1; in deinterlace_job_abort()
|
| /linux-4.1.27/drivers/scsi/ |
| D | mesh.c | 160 int aborting; member
437 ms->aborting = 0; in mesh_start_cmd()
972 ms->aborting = 1; in reselected()
980 ms->aborting = 1; in do_abort()
1057 if (!ms->aborting) { in handle_error()
1419 if (ms->aborting) { in phase_mismatch()
1550 if (ms->aborting) { in cmd_complete()
|
| D | aha152x.c | 322 aborting = 0x0200, /* ABORT is pending */ enumerator
1541 if (CURRENT_SC->SCp.phase & aborting) { in seldo_run()
|
| /linux-4.1.27/drivers/media/platform/coda/ |
| D | coda.h | 200 int aborting; member
|
| D | coda-common.c | 940 } else if (!ctx->aborting) { in coda_pic_run_work()
944 if ((ctx->aborting || (!ctx->streamon_cap && !ctx->streamon_out)) && in coda_pic_run_work()
1015 if (ctx->aborting) { in coda_job_ready()
1030 ctx->aborting = 1; in coda_job_abort()
1388 ctx->aborting = 0; in coda_stop_streaming()
|
| D | coda-bit.c | 2025 if (ctx->aborting) { in coda_irq_handler()
|
| /linux-4.1.27/Documentation/blockdev/ |
| D | cciss.txt | 166 implements the first two of these actions, aborting the command, and
168 in aborting commands, and sometimes it appears they will not even
|
| /linux-4.1.27/Documentation/frv/ |
| D | atomic-ops.txt | 52 steps (1) and (4) will set CC3 to the Undefined, thus aborting the store in (4a), and causing the
|
| /linux-4.1.27/drivers/media/platform/ti-vpe/ |
| D | vpe.c | 381 unsigned int aborting; /* abort after next irq */ member
904 ctx->aborting = 1; in job_abort()
1284 if (ctx->aborting) in vpe_irq()
|
| /linux-4.1.27/Documentation/usb/ |
| D | WUSB-Design-overview.txt | 404 In dequeue() we are basically cancelling/aborting the transfer. We issue
|
| /linux-4.1.27/Documentation/ |
| D | DMA-API.txt | 310 aborting the request or even oopsing is better than doing nothing and
|
| /linux-4.1.27/Documentation/scsi/ |
| D | ChangeLog.sym53c8xx | 388 - Do a normal soft reset as first chip reset, since aborting current
|
| D | ChangeLog.lpfc | 195 * Clean up fast lookup array of the fcp_ring when aborting iocbs.
1558 * Fix ulpStatus for aborting I/Os overlaps with newer firmware
|