| /linux-4.1.27/arch/arm/mach-pxa/ |
| H A D | csb701.c | 15 .desc = "SW2",
|
| /linux-4.1.27/drivers/media/pci/cx18/ |
| H A D | cx18-irq.c | 63 "SW1: %x SW2: %x HW2: %x\n", sw1, sw2, hw2); cx18_irq_handler()
|
| H A D | cx18-scb.h | 28 /* NOTE: All ACK interrupts are in the SW2 register. All non-ACK interrupts
124 /* Value to write to register SW2 register set (0xC7003140) after the
|
| H A D | cx18-firmware.c | 441 * that flag in the SW2 status register has been cleared by the CPU cx18_firmware_init()
|
| /linux-4.1.27/arch/sh/boards/ |
| H A D | board-apsh4ad0a.c | 78 /* These are the factory default settings of SW1 and SW2. apsh4ad0a_mode_pins()
|
| H A D | board-apsh4a3a.c | 153 /* These are the factory default settings of SW1 and SW2. apsh4a3a_mode_pins()
|
| H A D | board-urquell.c | 35 * SW2 0x1x xxxx -> little endian
|
| /linux-4.1.27/arch/sh/boards/mach-rsk/ |
| H A D | devices-rsk7203.c | 99 .desc = "SW2",
|
| /linux-4.1.27/arch/mips/include/asm/sn/ |
| H A D | intr.h | 55 * L1 = SW2
|
| /linux-4.1.27/arch/arm/mach-shmobile/ |
| H A D | board-kzm9g.c | 536 GPIO_KEY(KEY_RIGHT, GPIO_PCF8575_PORT11, "SW2-R"),
537 GPIO_KEY(KEY_LEFT, GPIO_PCF8575_PORT12, "SW2-L"),
538 GPIO_KEY(KEY_ENTER, GPIO_PCF8575_PORT13, "SW2-P"),
539 GPIO_KEY(KEY_UP, GPIO_PCF8575_PORT14, "SW2-U"),
540 GPIO_KEY(KEY_DOWN, GPIO_PCF8575_PORT15, "SW2-D"),
|
| /linux-4.1.27/drivers/regulator/ |
| H A D | pfuze100-regulator.c | 290 PFUZE100_SW_REG(PFUZE100, SW2, PFUZE100_SW2VOL, 400000, 1975000, 25000),
307 PFUZE100_SW_REG(PFUZE200, SW2, PFUZE100_SW2VOL, 400000, 1975000, 25000),
324 PFUZE100_SWB_REG(PFUZE3000, SW2, PFUZE100_SW2VOL, 0x7, pfuze3000_sw2lo),
609 /* SW2~SW4 high bit check and modify the voltage value table */ pfuze100_regulator_probe()
|
| H A D | pcap-regulator.c | 140 VREG_INFO(SW2, PCAP_REG_SWCTRL, 6, 7, NA, NA),
236 VREG(VAUX4), VREG(VSIM), VREG(VSIM2), VREG(VVIB), VREG(SW1), VREG(SW2),
|
| H A D | ltc3589.c | 163 /* SW1, SW2, SW3, LDO2 */
231 LTC3589_LINEAR_REG(SW2, B2DTV1),
|
| H A D | mc13892-regulator.c | 272 MC13892_SW_DEFINE(SW2, SWITCHERS1, SWITCHERS1, mc13892_sw),
|
| /linux-4.1.27/include/linux/i2c/ |
| H A D | twl4030-madc.h | 40 * @method: RT, SW1, SW2
|
| /linux-4.1.27/drivers/iio/adc/ |
| H A D | twl4030-madc.c | 55 * @requests: Array of request struct corresponding to SW1, SW2 and RT
175 * SW1 and SW2 software conversions also called asynchronous or GPC request.
342 * corresponding to RT, SW1, SW2 conversion requests.
373 * corresponding to RT, SW1, SW2 conversion requests.
499 * corresponding to RT SW1 or SW2 conversion methods.
|
| /linux-4.1.27/sound/pci/ |
| H A D | ak4531_codec.c | 375 0x00, /* 11: Output Mixer SW2 */
378 0x00, /* 14: Lch Input Mixer SW2 */
379 0x00, /* 15: Rch Input Mixer SW2 */
|
| /linux-4.1.27/arch/avr32/boards/atstk1000/ |
| H A D | atstk1002.c | 278 #endif /* SW2 for MMC signal routing */
|
| /linux-4.1.27/include/linux/mfd/ |
| H A D | ezx-pcap.h | 130 #define SW2 18 macro
|
| /linux-4.1.27/arch/arm/mach-imx/ |
| H A D | mach-mx35_3ds.c | 344 .name = "SW2",
|
| /linux-4.1.27/drivers/net/appletalk/ |
| H A D | ltpc.c | 174 * SW2 IRQ 3
|
| /linux-4.1.27/drivers/watchdog/ |
| H A D | pcwd.c | 124 (1:SW1 <-> 0:SW2) */
|
| /linux-4.1.27/drivers/net/ethernet/intel/i40e/ |
| H A D | i40e_main.c | 4594 /* Do not enable DCB for SW1 and SW2 images even if the FW is capable */ i40e_init_pf_dcb()
|