Searched refs:CRT (Results 1 – 15 of 15) sorted by relevance
| /linux-4.1.27/Documentation/fb/ |
| D | viafb.txt | 14 Device: CRT, LCD, DVI
17 CRT:
37 viafb_active_dev=CRT+DVI viafb_dvi_port=DVP1
106 This option is used to specify active devices.(CRT, DVI, CRT+LCD...)
115 To enable two devices, such as CRT+DVI:
116 modprobe viafb viafb_active_dev=CRT+DVI;
119 modprobe viafb viafb_active_dev=CRT+DVI
121 modprobe viafb viafb_active_dev=DVI+CRT...
124 If CRT is primary and DVI is secondary, we should use:
125 modprobe viafb viafb_active_dev=CRT+DVI viafb_SAMM_ON=1...
[all …]
|
| D | modedb.txt | 74 The GTF is limited by the fact that it is designed mainly for CRT displays.
80 The CVT addresses these limitations. If used with CRT's, the formula used
87 new CRT displays and probably with most flatpanels, if 'reduced blanking'
|
| /linux-4.1.27/Documentation/ABI/testing/ |
| D | sysfs-platform-eeepc-laptop | 8 - 2 = CRT
9 - 3 = LCD+CRT
|
| D | sysfs-platform-asus-laptop | 10 ||`-- CRT
14 - 3 (0011b) CRT+LCD.
|
| /linux-4.1.27/arch/sh/cchips/ |
| D | Kconfig | 16 CRT color controller, IrDA up to 4 Mbps, and a
|
| /linux-4.1.27/drivers/staging/sm750fb/ |
| D | ddk750_mode.c | 64 dispControl = FIELD_SET(dispControl, CRT_DISPLAY_CTRL, CRTSELECT, CRT); in displayControlAdjust_SM750LE()
|
| /linux-4.1.27/arch/m32r/platforms/mappi/ |
| D | dot.gdbinit | 100 # LCD & CRT dual-head setting (8bpp)
|
| D | dot.gdbinit.nommu | 100 # LCD & CRT dual-head setting (8bpp)
|
| D | dot.gdbinit.smp | 164 # LCD & CRT dual-head setting (8bpp)
|
| /linux-4.1.27/Documentation/laptops/ |
| D | asus-laptop.txt | 114 | Bin | Val | DVI | TV | CRT | LCD |
|
| D | thinkpad-acpi.txt | 616 LCD, CRT or DVI (if available). The following commands are available:
|
| /linux-4.1.27/drivers/video/fbdev/ |
| D | cirrusfb.c | 349 CRT, enumerator
2831 case CRT: in cirrusfb_dbg_print_regs()
2865 cirrusfb_dbg_print_regs(info, regbase, CRT, in cirrusfb_dbg_reg_dump()
|
| D | Kconfig | 2092 Frame buffer driver for the CRT and LCD controllers in the Silicon
|
| /linux-4.1.27/drivers/pinctrl/ |
| D | pinctrl-tegra20.c | 2058 MUX_PG(crtp, CRT, RSVD2, RSVD3, RSVD4, 0x20, 14, 0x98, 20, 0xa4, 24),
2115 MUX_PG(lm1, DISPLAYA, DISPLAYB, RSVD3, CRT, 0x1c, 25, 0x90, 28, -1, -1),
|
| D | pinctrl-tegra30.c | 2352 …PINGROUP(crt_hsync_pv6, CRT, RSVD2, RSVD3, RSVD4, 0x311c, N, …
2353 …PINGROUP(crt_vsync_pv7, CRT, RSVD2, RSVD3, RSVD4, 0x3120, N, …
|