| /linux-4.1.27/include/linux/mfd/ |
| H A D | max8998.h | 76 * registers set by buck?_voltage?. The voltage of BUCK1/2 cannot
78 * @buck1_voltage: BUCK1 DVS mode 1 voltage registers
80 * @buck1_set1: BUCK1 gpio pin 1 to set output voltage
81 * @buck1_set2: BUCK1 gpio pin 2 to set output voltage
82 * @buck1_default_idx: Default for BUCK1 gpio pin 1, 2
|
| H A D | 88pm80x.h | 131 /* Regulator Control Registers: BUCK1,BUCK5,LDO1 have DVC */
|
| /linux-4.1.27/drivers/regulator/ |
| H A D | lp8788-buck.c | 86 BUCK1, enumerator in enum:lp8788_buck_id
158 case BUCK1: lp8788_set_dvs()
175 case BUCK1: lp8788_get_buck_dvs_ctrl_mode()
217 case BUCK1: lp8788_select_buck_vout_addr()
376 .id = BUCK1,
434 case BUCK1: lp8788_dvs_gpio_request()
476 if ((id == BUCK1 && !pdata->buck1_dvs) || lp8788_init_dvs()
|
| H A D | 88pm800.c | 48 /* BUCK1 with DVC[0..3] */
204 PM800_BUCK(BUCK1, BUCK_ENA, 0, 3000000, buck1_volt_range, 0x55),
238 PM800_REGULATOR_OF_MATCH(buck1, BUCK1),
|
| H A D | max8998.c | 110 &buck12_voltage_map_desc, /* BUCK1 */
326 "BUCK1, selector:%d, buck1_vol1:%d, buck1_vol2:%d\n" max8998_set_voltage_buck_sel()
570 .name = "BUCK1",
811 /* Set predefined values for BUCK1 registers */ max8998_pmic_probe()
|
| H A D | da9052-regulator.c | 334 DA9052_DCDC(BUCK1, 25, 500, 2075, 6, 6, DA9052_SUPPLY_VBCOREGO),
351 DA9052_DCDC(BUCK1, 25, 500, 2075, 6, 6, DA9052_SUPPLY_VBCOREGO),
|
| H A D | s5m8767.c | 157 /* BUCK1 ... BUCK9 */
158 {0x0, 0x3, 0x1, 0x1}, /* BUCK1 */
423 s5m8767_regulator_desc(BUCK1),
|
| H A D | da9055-regulator.c | 429 DA9055_BUCK(BUCK1, 25, 725, 2075, 6, 9, 0xc, 2),
540 { .name = "BUCK1", },
|
| H A D | hi6421-regulator.c | 111 HI6421_REGULATOR_OF_MATCH(hi6421_buck1, BUCK1),
379 HI6421_BUCK012(BUCK1, 0x0f, 0x7f, 0x0e, 0x01, 0x10, 400, 20000),
|
| H A D | 88pm8607.c | 293 PM8607_DVC(BUCK1, GO, BIT(0), SUPPLIES_EN11, 0),
|
| H A D | max8997.c | 463 * For LDO1 ~ LDO21, BUCK1~5, BUCK7, CHARGER, CHARGER_TOPOFF
464 * BUCK1, 2, and 5 are available if they are not controlled by gpio
549 * Assess the damage on the voltage setting of BUCK1,2,5 by the change.
875 MAX8997_VOLTAGE_REGULATOR(BUCK1, max8997_buck_ops),
|
| H A D | da903x.c | 398 DA9034_DVC(BUCK1, 725, 1500, 25, ADTV2, 5, VCC1, 0, OVER1, 0),
|
| H A D | max77802.c | 273 /* For BUCK1, 6 */ max77802_set_ramp_delay_4bit()
|
| /linux-4.1.27/arch/arm/mach-s3c64xx/ |
| H A D | mach-smdk6410.c | 301 /* VDDARM, BUCK1 on J5 */
|