struct usb_device

struct usb_device
Prev	Chapter 4. Host-Side Data Types and Macros	Next

Name

struct usb_device — kernel's representation of a USB device

Synopsis

struct usb_device {
  int devnum;
  char devpath[16];
  u32 route;
  enum usb_device_state state;
  enum usb_device_speed speed;
  struct usb_tt * tt;
  int ttport;
  unsigned int toggle[2];
  struct usb_device * parent;
  struct usb_bus * bus;
  struct usb_host_endpoint ep0;
  struct device dev;
  struct usb_device_descriptor descriptor;
  struct usb_host_bos * bos;
  struct usb_host_config * config;
  struct usb_host_config * actconfig;
  struct usb_host_endpoint * ep_in[16];
  struct usb_host_endpoint * ep_out[16];
  char ** rawdescriptors;
  unsigned short bus_mA;
  u8 portnum;
  u8 level;
  unsigned can_submit:1;
  unsigned persist_enabled:1;
  unsigned have_langid:1;
  unsigned authorized:1;
  unsigned authenticated:1;
  unsigned wusb:1;
  unsigned lpm_capable:1;
  unsigned usb2_hw_lpm_capable:1;
  unsigned usb2_hw_lpm_besl_capable:1;
  unsigned usb2_hw_lpm_enabled:1;
  unsigned usb2_hw_lpm_allowed:1;
  unsigned usb3_lpm_enabled:1;
  int string_langid;
  char * product;
  char * manufacturer;
  char * serial;
  struct list_head filelist;
  int maxchild;
  u32 quirks;
  atomic_t urbnum;
  unsigned long active_duration;
#ifdef CONFIG_PM
  unsigned long connect_time;
  unsigned do_remote_wakeup:1;
  unsigned reset_resume:1;
  unsigned port_is_suspended:1;
#endif
  struct wusb_dev * wusb_dev;
  int slot_id;
  enum usb_device_removable removable;
  struct usb2_lpm_parameters l1_params;
  struct usb3_lpm_parameters u1_params;
  struct usb3_lpm_parameters u2_params;
  unsigned lpm_disable_count;
};

Members

devnum: device number; address on a USB bus
devpath[16]: device ID string for use in messages (e.g., /port/...)
route: tree topology hex string for use with xHCI
state: device state: configured, not attached, etc.
speed: device speed: high/full/low (or error)
tt: Transaction Translator info; used with low/full speed dev, highspeed hub
ttport: device port on that tt hub
toggle[2]: one bit for each endpoint, with ([0] = IN, [1] = OUT) endpoints
parent: our hub, unless we're the root
bus: bus we're part of
ep0: endpoint 0 data (default control pipe)
dev: generic device interface
descriptor: USB device descriptor
bos: USB device BOS descriptor set
config: all of the device's configs
actconfig: the active configuration
ep_in[16]: array of IN endpoints
ep_out[16]: array of OUT endpoints
rawdescriptors: raw descriptors for each config
bus_mA: Current available from the bus
portnum: parent port number (origin 1)
level: number of USB hub ancestors
can_submit: URBs may be submitted
persist_enabled: USB_PERSIST enabled for this device
have_langid: whether string_langid is valid
authorized: policy has said we can use it; (user space) policy determines if we authorize this device to be used or not. By default, wired USB devices are authorized. WUSB devices are not, until we authorize them from user space. FIXME -- complete doc
authenticated: Crypto authentication passed
wusb: device is Wireless USB
lpm_capable: device supports LPM
usb2_hw_lpm_capable: device can perform USB2 hardware LPM
usb2_hw_lpm_besl_capable: device can perform USB2 hardware BESL LPM
usb2_hw_lpm_enabled: USB2 hardware LPM is enabled
usb2_hw_lpm_allowed: Userspace allows USB 2.0 LPM to be enabled
usb3_lpm_enabled: USB3 hardware LPM enabled
string_langid: language ID for strings
product: iProduct string, if present (static)
manufacturer: iManufacturer string, if present (static)
serial: iSerialNumber string, if present (static)
filelist: usbfs files that are open to this device
maxchild: number of ports if hub
quirks: quirks of the whole device
urbnum: number of URBs submitted for the whole device
active_duration: total time device is not suspended
connect_time: time device was first connected
do_remote_wakeup: remote wakeup should be enabled
reset_resume: needs reset instead of resume
port_is_suspended: the upstream port is suspended (L2 or U3)
wusb_dev: if this is a Wireless USB device, link to the WUSB specific data for the device.
slot_id: Slot ID assigned by xHCI
removable: Device can be physically removed from this port
l1_params: best effor service latency for USB2 L1 LPM state, and L1 timeout.
u1_params: exit latencies for USB3 U1 LPM state, and hub-initiated timeout.
u2_params: exit latencies for USB3 U2 LPM state, and hub-initiated timeout.
lpm_disable_count: Ref count used by usb_disable_lpm and usb_enable_lpm to keep track of the number of functions that require USB 3.0 Link Power Management to be disabled for this usb_device. This count should only be manipulated by those functions, with the bandwidth_mutex is held.

Notes

Usbcore drivers should not set usbdev->state directly. Instead use usb_set_device_state.