59 #  define LOGNAME			"msnd_classic"  macro
65 #  define LOGNAME			"msnd_pinnacle"  macro
691 			printk(KERN_DEBUG LOGNAME ": Stopping read for %p\n", file);  in dsp_halt()
703 			printk(KERN_DEBUG LOGNAME ": Stopping write for %p\n", file);  in dsp_halt()
724 			printk(KERN_DEBUG LOGNAME ": Starting write for %p\n", file);  in dsp_open()
735 			printk(KERN_DEBUG LOGNAME ": Starting read for %p\n", file);  in dsp_open()
1145 	printk(KERN_ERR LOGNAME ": Cannot reset DSP\n");  in reset_dsp()
1159 		printk(KERN_ERR LOGNAME ": I/O port conflict\n");  in probe_multisound()
1170 	printk(KERN_INFO LOGNAME ": %s, "  in probe_multisound()
1193 	printk(KERN_INFO LOGNAME ": %s revision %s, Xilinx version %s, "  in probe_multisound()
1294 	printk(KERN_WARNING LOGNAME ": ADC calibration failed\n");  in calibrate_adc()
1307 		printk(KERN_ERR LOGNAME ": Error loading " INITCODEFILE);  in upload_dsp_code()
1313 		printk(KERN_ERR LOGNAME ": Error loading " PERMCODEFILE);  in upload_dsp_code()
1320 		printk(KERN_WARNING LOGNAME ": Error uploading to DSP\n");  in upload_dsp_code()
1325 	printk(KERN_INFO LOGNAME ": DSP firmware uploaded (resident)\n");  in upload_dsp_code()
1327 	printk(KERN_INFO LOGNAME ": DSP firmware uploaded\n");  in upload_dsp_code()
1360 		printk(KERN_WARNING LOGNAME ": Cannot initialize SMA\n");  in initialize()
1368 		printk(KERN_WARNING LOGNAME ": Cannot upload DSP code\n");  in initialize()
1376 			printk(KERN_DEBUG LOGNAME ": DSP reset timeout\n");  in initialize()
1394 	printk(KERN_INFO LOGNAME ": DSP reset\n");  in dsp_full_reset()
1397 		printk(KERN_WARNING LOGNAME ": DSP reset failed\n");  in dsp_full_reset()
1410 		printk(KERN_ERR LOGNAME ": Couldn't grab IRQ %d\n", dev.irq);  in attach_multisound()
1426 		printk(KERN_ERR LOGNAME ": Unable to register MultiSound\n");  in attach_multisound()
1433 		printk(KERN_ERR LOGNAME ": Unable to register DSP operations\n");  in attach_multisound()
1441 		printk(KERN_ERR LOGNAME ": Unable to register mixer operations\n");  in attach_multisound()
1478 		printk(KERN_ERR LOGNAME ": msnd_write_cfg: I/O error\n");  in msnd_write_cfg()
1572 		printk(KERN_INFO LOGNAME ": Resetting all devices\n");  in msnd_pinnacle_cfg_devices()
1589 			printk(KERN_INFO LOGNAME  in msnd_pinnacle_cfg_devices()
1596 			printk(KERN_INFO LOGNAME  in msnd_pinnacle_cfg_devices()
1603 			printk(KERN_INFO LOGNAME  in msnd_pinnacle_cfg_devices()
1753 	printk(KERN_INFO LOGNAME ": Turtle Beach " LONGNAME " Linux Driver Version "  in msnd_init()
1757 		printk(KERN_WARNING LOGNAME ": io, irq and mem must be set\n");  in msnd_init()
1769 …printk(KERN_ERR LOGNAME ": \"io\" - DSP I/O base must be set to 0x210, 0x220, 0x230, 0x240, 0x250,…  in msnd_init()
1777 …printk(KERN_ERR LOGNAME ": \"io\" - DSP I/O base must within the range 0x100 to 0x3E0 and must be …  in msnd_init()
1789 		printk(KERN_ERR LOGNAME ": \"irq\" - must be set to 5, 7, 9, 10, 11 or 12\n");  in msnd_init()
1800 		printk(KERN_ERR LOGNAME ": \"mem\" - must be set to "  in msnd_init()
1825 		printk(KERN_INFO LOGNAME ": Assuming PnP mode\n");  in msnd_init()
1827 …printk(KERN_INFO LOGNAME ": Config port must be 0x250, 0x260 or 0x270 (or unspecified for PnP mode…  in msnd_init()
1830 		printk(KERN_INFO LOGNAME ": Non-PnP mode: configuring at port 0x%x\n", cfg);  in msnd_init()
1852 			printk(KERN_ERR LOGNAME ": Config port 0x%x conflict\n", cfg);  in msnd_init()
1857 			printk(KERN_ERR LOGNAME ": Device configuration error\n");  in msnd_init()
1902 	printk(KERN_INFO LOGNAME ": %u byte audio FIFOs (x2)\n", dev.fifosize);  in msnd_init()
1904 		printk(KERN_ERR LOGNAME ": Couldn't allocate write FIFO\n");  in msnd_init()
1909 		printk(KERN_ERR LOGNAME ": Couldn't allocate read FIFO\n");  in msnd_init()
1915 		printk(KERN_ERR LOGNAME ": Probe failed\n");  in msnd_init()
1922 		printk(KERN_ERR LOGNAME ": Attach failed\n");  in msnd_init()