75 #  define LOGNAME			"msnd_classic"  macro
79 #  define LOGNAME			"snd_msnd_pinnacle"  macro
138 			snd_printd(KERN_WARNING LOGNAME ": Play underflow %i\n",  in snd_msnd_eval_dsp_msg()
145 			snd_printd(KERN_WARNING LOGNAME ": Record overflow\n");  in snd_msnd_eval_dsp_msg()
150 			snd_printd(KERN_WARNING LOGNAME  in snd_msnd_eval_dsp_msg()
163 		snd_printd(KERN_WARNING LOGNAME ": HIMT message %d 0x%02x\n",  in snd_msnd_eval_dsp_msg()
213 	snd_printk(KERN_ERR LOGNAME ": Cannot reset DSP\n");  in snd_msnd_reset_dsp()
229 		snd_printk(KERN_ERR LOGNAME ": I/O port conflict\n");  in snd_msnd_probe()
241 	printk(KERN_INFO LOGNAME ": %s, "  in snd_msnd_probe()
301 	printk(KERN_INFO LOGNAME ": %s revision %s, Xilinx version %s, "  in snd_msnd_probe()
393 		printk(KERN_ERR LOGNAME ": Error loading " INITCODEFILE);  in upload_dsp_code()
398 		printk(KERN_ERR LOGNAME ": Error loading " PERMCODEFILE);  in upload_dsp_code()
404 		printk(KERN_WARNING LOGNAME ": Error uploading to DSP\n");  in upload_dsp_code()
408 	printk(KERN_INFO LOGNAME ": DSP firmware uploaded\n");  in upload_dsp_code()
441 		printk(KERN_WARNING LOGNAME ": Cannot initialize SMA\n");  in snd_msnd_initialize()
451 		printk(KERN_WARNING LOGNAME ": Cannot upload DSP code\n");  in snd_msnd_initialize()
460 			snd_printd(KERN_ERR LOGNAME ": DSP reset timeout\n");  in snd_msnd_initialize()
482 		printk(KERN_WARNING LOGNAME ": DSP reset failed\n");  in snd_msnd_dsp_full_reset()
517 	printk(KERN_WARNING LOGNAME ": ADC calibration failed\n");  in snd_msnd_calibrate_adc()
551 		printk(KERN_ERR LOGNAME ": Couldn't grab IRQ %d\n", chip->irq);  in snd_msnd_attach()
560 		printk(KERN_ERR LOGNAME  in snd_msnd_attach()
569 		printk(KERN_ERR LOGNAME  in snd_msnd_attach()
587 		printk(KERN_ERR LOGNAME ": error creating new PCM device\n");  in snd_msnd_attach()
593 		printk(KERN_ERR LOGNAME ": error creating new Mixer device\n");  in snd_msnd_attach()
608 			printk(KERN_ERR LOGNAME  in snd_msnd_attach()
658 		printk(KERN_ERR LOGNAME ": snd_msnd_write_cfg: I/O error\n");  in snd_msnd_write_cfg()
747 	printk(KERN_INFO LOGNAME ": Resetting all devices\n");  in snd_msnd_pinnacle_cfg_reset()
828 		printk(KERN_WARNING LOGNAME ": io, irq and mem must be set\n");  in snd_msnd_isa_match()
841 		printk(KERN_ERR LOGNAME ": \"io\" - DSP I/O base must be set "  in snd_msnd_isa_match()
848 		printk(KERN_ERR LOGNAME  in snd_msnd_isa_match()
861 		printk(KERN_ERR LOGNAME  in snd_msnd_isa_match()
872 		printk(KERN_ERR LOGNAME ": \"mem\" - must be set to "  in snd_msnd_isa_match()
880 		printk(KERN_INFO LOGNAME ": Assuming PnP mode\n");  in snd_msnd_isa_match()
882 		printk(KERN_INFO LOGNAME  in snd_msnd_isa_match()
903 		printk(KERN_INFO LOGNAME ": Assuming PnP mode\n");  in snd_msnd_isa_probe()
946 	printk(KERN_INFO LOGNAME ": Non-PnP mode: configuring at port 0x%lx\n",  in snd_msnd_isa_probe()
950 		printk(KERN_ERR LOGNAME ": Config port 0x%lx conflict\n",  in snd_msnd_isa_probe()
974 		printk(KERN_INFO LOGNAME  in snd_msnd_isa_probe()
989 		printk(KERN_INFO LOGNAME  in snd_msnd_isa_probe()
1002 		printk(KERN_INFO LOGNAME  in snd_msnd_isa_probe()
1041 		printk(KERN_ERR LOGNAME ": Probe failed\n");  in snd_msnd_isa_probe()
1048 		printk(KERN_ERR LOGNAME ": Attach failed\n");  in snd_msnd_isa_probe()
1166 		printk(KERN_ERR LOGNAME ": Probe failed\n");  in snd_msnd_pnp_detect()
1172 		printk(KERN_ERR LOGNAME ": Attach failed\n");  in snd_msnd_pnp_detect()