Lines Matching refs:you
26 This selects the ARM(R) AMBA(R) PrimeCell PL010 UART. If you have
27 an Integrator/AP or Integrator/PP2 platform, or if you have a
37 Say Y here if you wish to use an AMBA PrimeCell UART as the system
41 Even if you say Y here, the currently visible framebuffer console
43 you can alter that using a kernel command line option such as
53 This selects the ARM(R) AMBA(R) PrimeCell PL011 UART. If you have
65 Say Y here if you wish to use an AMBA PrimeCell UART as the system
69 Even if you say Y here, the currently visible framebuffer console
71 you can alter that using a kernel command line option such as
109 If you say Y here, it will be possible to use a serial port as the
130 Say Y here if you wish to use an on-chip UART on a Atmel
140 Say Y here if you wish to use the PDC to do DMA transfers to
154 Say Y here if you wish to have the internal AT91 / AT32 UARTs
157 64). This is necessary if you also want other UARTs, such as
162 To use this, you should create suitable ttyATn device nodes in
165 Say Y if you have an external 8250/16C550 UART. If unsure, say N.
171 This special driver allows you to temporary use NMI debugger port
174 Unlike KDB's disable_nmi command, with this driver you are always
180 communication methods, for things like PPP you still must fully
198 Say Y here if you wish to use a KS8695 (Centaur) UART as the
216 Say Y here if you wish to use a Amlogic MesonX UART as the
235 Even if you say Y here, the currently visible virtual console
237 you can alter that using a kernel command line option such as
284 Even if you say Y here, the currently visible virtual console
286 you can alter that using a kernel command line option such as
306 Even if you say Y here, the currently visible virtual console
308 you can alter that using a kernel command line option such as
343 Say Y here if you want to support this ICs.
360 If you say Y here, it will be possible to use a serial port as the
390 If you say Y here, it will be possible to use a serial port as the
405 If you have a machine based on a 21285 (Footbridge) StrongARM(R)/
406 PCI bridge you can enable its onboard serial port by enabling this
414 If you have enabled the serial port on the 21285 footbridge you can
417 Even if you say Y here, the currently visible virtual console
419 you can alter that using a kernel command line option such as
429 Say Y here if you want to use the Marvell MPSC serial controller.
436 Say Y here if you want to support a serial console on a Marvell MPSC.
443 If you have a machine based on an Intel XScale PXA2xx CPU you
451 If you have enabled the serial port on the Intel XScale PXA
452 CPU you can make it the console by answering Y to this option.
454 Even if you say Y here, the currently visible virtual console
456 you can alter that using a kernel command line option such as
466 If you have a machine based on a SA1100/SA1110 StrongARM(R) CPU you
476 If you have enabled the serial port on the SA1100/SA1110 StrongARM
477 CPU you can make it the console by answering Y to this option.
479 Even if you say Y here, the currently visible virtual console
481 you can alter that using a kernel command line option such as
578 If you have a machine based on a Motorola IMX CPU you
587 If you have enabled the serial port on the Freescale IMX
588 CPU you can make it the console by answering Y to this option.
590 Even if you say Y here, the currently visible virtual console
592 you can alter that using a kernel command line option such as
601 Say Y here if you want to use the Xilinx uartlite serial controller.
611 Say Y here if you wish to use a Xilinx uartlite as the system
627 systems. Say Y or M if you want to be able to these serial ports.
633 If you would like to be able to use the Zilog8530 serial port
634 on your Sparc system as the console, you can do so by answering
642 mouse on (PCI) UltraSPARC systems. Say Y or M if you want to be able
649 If you would like to be able to use the SU serial port
650 on your Sparc system as the console, you can do so by answering
668 3. Add device ttyB0 to /etc/securetty (if you want to log on as
690 3. Add device ttyB0 to /etc/securetty (if you want to log on as
699 (PCI) UltraSPARC systems. Say Y or M if you want to be able to these
706 If you would like to be able to use the SAB82532 serial port
707 on your Sparc system as the console, you can do so by answering
715 systems. Say Y if you want to be able to use this device.
723 systems. Say Y or M if you want to be able to these serial ports.
754 If you have a MIPS-based Philips SoC such as PNX8330 and you want
762 If you have a MIPS-based Philips SoC such as PNX8330 and you want
780 If you would like to be able to use one of the high speed serial
781 ports on the LPC32XX as the console, you can do so by answering
816 This setting lets you define what the default baudrate is for the
834 Say Y or M if you want to be able to these serial ports.
843 the two drivers being unable to coexist; you could not use
853 If you enable this option, any z85c30 ports in the system will
854 be registered as ttyS0 onwards as in the past, and you will be
858 Say N unless you need the z85c30 ports on your (Power)Mac
866 If you would like to be able to use the z85c30 serial port
867 on your (Power)Mac as the console, you can do so by answering
883 Say Y here if you wish to use a SCC or SMC CPM UART as the system
887 Even if you say Y here, the currently visible framebuffer console
889 you can alter that using a kernel command line option such as
900 If you have an SGI Altix and you would like to use the system
901 controller serial port as your console (you want this!),
909 This driver supports MPC52xx and MPC512x PSC serial ports. If you would
910 like to use them, you must answer Y or M to this option. Note that
919 Select this options if you'd like to use one of the PSC serial port
950 Say Y here if you want to use the M32R serial controller.
957 Say Y here if you want to support a serial console.
959 If you use an M3T-M32700UT or an OPSPUT platform,
967 Say Y here if you want to use the M32R serial controller
970 If you use an M3T-M32700UT or an OPSPUT platform,
1001 If you have a NEC VR4100 series processor and you want to use
1010 If you have a NEC VR4100 series processor and you want to use
1024 If you have a card like this, say Y here, otherwise say N.
1034 If you have an SGI Altix with an IOC4 based Base IO card
1043 If you have an SGI Altix with an IOC3 serial card,
1083 If you have a machine based on a Hilscher NetX SoC you
1094 If you have enabled the serial port on the Hilscher NetX SoC
1095 you can make it the console by answering Y to this option.
1102 If you have a PowerPC based system that has serial ports
1103 on a platform specific bus, you should enable this option.
1112 If you have a machine based on an Texas Instruments OMAP CPU you
1115 By enabling this option you take advantage of dma feature available
1124 Select this option if you would like to use omap serial port as
1127 Even if you say Y here, the currently visible virtual console
1129 you can alter that using a kernel command line option such as
1310 If you have enabled the serial port on the BCM63xx CPU
1311 you can make it the console by answering Y to this option.
1359 This setting lets you define the maximum number of the Altera
1368 This setting lets you define what the default baudrate is for the
1407 Say Y here if you wish to use the PCH UART as the system console
1447 If you have an Atheros AR933X SOC based board and want to use the
1465 Set this to the number of serial ports you want the driver
1511 Set this to the number of serial ports you want the driver
1527 If you want to compile this driver into the kernel, say Y here. If
1528 you don't have a suitable RocketPort card installed, say N.
1551 If you have enabled the lpuart serial port on the Freescale SoCs,
1552 you can make it the console by answering Y to this option.
1566 If you have enabled the USART serial port on Conexant Digicolor
1567 SoCs, you can make it the console by answering Y to this option.