172 			hw_dbg(hw, "I2C byte read combined error - Retry.\n");  in ixgbe_read_i2c_combined_generic_int()
174 			hw_dbg(hw, "I2C byte read combined error.\n");  in ixgbe_read_i2c_combined_generic_int()
267 			hw_dbg(hw, "I2C byte write combined error - Retry.\n");  in ixgbe_write_i2c_combined_generic_int()
269 			hw_dbg(hw, "I2C byte write combined error.\n");  in ixgbe_write_i2c_combined_generic_int()
375 		hw_dbg(hw, "MNG_VETO bit detected.\n");  in ixgbe_check_reset_blocked()
489 		hw_dbg(hw, "PHY reset polling failed to complete.\n");  in ixgbe_reset_phy_generic()
530 		hw_dbg(hw, "PHY address command did not complete.\n");  in ixgbe_read_phy_reg_mdi()
557 		hw_dbg(hw, "PHY read command didn't complete\n");  in ixgbe_read_phy_reg_mdi()
633 		hw_dbg(hw, "PHY address cmd didn't complete\n");  in ixgbe_write_phy_reg_mdi()
661 		hw_dbg(hw, "PHY write cmd didn't complete\n");  in ixgbe_write_phy_reg_mdi()
1054 		hw_dbg(hw, "PHY reset did not complete.\n");  in ixgbe_reset_phy_nl()
1079 			hw_dbg(hw, "DELAY: %d MS\n", edata);  in ixgbe_reset_phy_nl()
1083 			hw_dbg(hw, "DATA:\n");  in ixgbe_reset_phy_nl()
1096 				hw_dbg(hw, "Wrote %4.4x to %4.4x\n", eword,  in ixgbe_reset_phy_nl()
1104 			hw_dbg(hw, "CONTROL:\n");  in ixgbe_reset_phy_nl()
1106 				hw_dbg(hw, "EOL\n");  in ixgbe_reset_phy_nl()
1109 				hw_dbg(hw, "SOL\n");  in ixgbe_reset_phy_nl()
1111 				hw_dbg(hw, "Bad control value\n");  in ixgbe_reset_phy_nl()
1116 			hw_dbg(hw, "Bad control type\n");  in ixgbe_reset_phy_nl()
1399 		hw_dbg(hw, "SFP+ module not supported\n");  in ixgbe_identify_sfp_module_generic()
1578 			hw_dbg(hw, "QSFP module not supported\n");  in ixgbe_identify_qsfp_module_generic()
1661 				hw_dbg(hw, "SFP+ module not supported\n");  in ixgbe_get_sfp_init_sequence_offsets()
1674 		hw_dbg(hw, "No matching SFP+ module found\n");  in ixgbe_get_sfp_init_sequence_offsets()
1827 			hw_dbg(hw, "I2C byte read error - Retrying.\n");  in ixgbe_read_i2c_byte_generic_int()
1829 			hw_dbg(hw, "I2C byte read error.\n");  in ixgbe_read_i2c_byte_generic_int()
1925 			hw_dbg(hw, "I2C byte write error - Retrying.\n");  in ixgbe_write_i2c_byte_generic_int()
1927 			hw_dbg(hw, "I2C byte write error.\n");  in ixgbe_write_i2c_byte_generic_int()
2126 		hw_dbg(hw, "I2C ack was not received.\n");  in ixgbe_get_i2c_ack()
2198 		hw_dbg(hw, "I2C data was not set to %X\n", data);  in ixgbe_clock_out_i2c_bit()
2294 		hw_dbg(hw, "Error - I2C data was not set to %X.\n", data);  in ixgbe_set_i2c_data()