24 #define dprintk(args...) do { if (debug) { printk(KERN_DEBUG "DiB7000M: "); printk(args); printk("\…  macro
77 		dprintk("could not acquire lock");  in dib7000m_read_word()
95 		dprintk("i2c read error on %d",reg);  in dib7000m_read_word()
108 		dprintk("could not acquire lock");  in dib7000m_write_word()
157 	dprintk( "setting output mode for demod %p to %d", &state->demod, mode);  in dib7000m_set_output_mode()
184 			dprintk( "Unhandled output_mode passed to be set for demod %p",&state->demod);  in dib7000m_set_output_mode()
323 		dprintk( "using default timf");  in dib7000m_set_bandwidth()
326 		dprintk( "using updated timf");  in dib7000m_set_bandwidth()
343 		dprintk( "diversity combination deactivated - forced by COFDM parameters");  in dib7000m_set_diversity_in()
583 		dprintk( "GPIO reset was not successful.");  in dib7000m_demod_reset()
586 		dprintk( "OUTPUT_MODE could not be reset.");  in dib7000m_demod_reset()
653 	dprintk( "AGC split_offset: %d",split_offset);  in dib7000m_agc_soft_split()
690 		dprintk( "no valid AGC configuration found for band 0x%02x",band);  in dib7000m_set_agc_config()
706 	dprintk( "WBD: ref: %d, sel: %d, active: %d, alpha: %d",  in dib7000m_set_agc_config()
745 	dprintk( "updated timf_frequency: %d (default: %d)",state->timf, state->timf_default);  in dib7000m_update_timf()
807 			dprintk( "SPLIT %p: %hd", demod, agc_split);  in dib7000m_agc_startup()
1016 		dprintk( "autosearch failed");  in dib7000m_autosearch_irq()
1021 		dprintk( "autosearch succeeded");  in dib7000m_autosearch_irq()
1105 		dprintk( "could not start Slow ADC");  in dib7000m_wakeup()
1124 		dprintk( "wrong Vendor ID (0x%x)",value);  in dib7000m_identify()
1133 		dprintk( "wrong Device ID (0x%x)",value);  in dib7000m_identify()
1139 		dprintk( "this driver does not work with DiB7000PC");  in dib7000m_identify()
1144 		case 0x4000: dprintk( "found DiB7000MA/PA/MB/PB"); break;  in dib7000m_identify()
1145 		case 0x4001: state->reg_offs = 1; dprintk( "found DiB7000HC"); break;  in dib7000m_identify()
1146 		case 0x4002: state->reg_offs = 1; dprintk( "found DiB7000MC"); break;  in dib7000m_identify()
1147 		case 0x4003: state->reg_offs = 1; dprintk( "found DiB9000"); break;  in dib7000m_identify()
1245 		dprintk("autosearch returns: %d",found);  in dib7000m_set_frontend()
1333 	dprintk("PID filter enabled %d", onoff);  in dib7000m_pid_filter_ctrl()
1341 	dprintk("PID filter: index %x, PID %d, OnOff %d", id, pid, onoff);  in dib7000m_pid_filter()
1365 				dprintk("DiB7000M #%d: not identified", k);
1378 		dprintk("IC %d initialized (to i2c_address 0x%x)", k, new_addr);