265 			dev_err(&i2c->dev, "bu21013_do_touch_report failed\n");  in bu21013_gpio_irq()
293 		dev_err(&i2c->dev, "BU21013_RESET reg write failed\n");  in bu21013_init_chip()
301 		dev_err(&i2c->dev, "BU21013_SENSOR_0_7 reg write failed\n");  in bu21013_init_chip()
308 		dev_err(&i2c->dev, "BU21013_SENSOR_8_15 reg write failed\n");  in bu21013_init_chip()
315 		dev_err(&i2c->dev, "BU21013_SENSOR_16_23 reg write failed\n");  in bu21013_init_chip()
322 		dev_err(&i2c->dev, "BU21013_POS_MODE1 reg write failed\n");  in bu21013_init_chip()
331 		dev_err(&i2c->dev, "BU21013_POS_MODE2 reg write failed\n");  in bu21013_init_chip()
342 		dev_err(&i2c->dev, "BU21013_CLK_MODE reg write failed\n");  in bu21013_init_chip()
349 		dev_err(&i2c->dev, "BU21013_IDLE reg write failed\n");  in bu21013_init_chip()
356 		dev_err(&i2c->dev, "BU21013_INT_MODE reg write failed\n");  in bu21013_init_chip()
364 		dev_err(&i2c->dev, "BU21013_FILTER reg write failed\n");  in bu21013_init_chip()
371 		dev_err(&i2c->dev, "BU21013_TH_ON reg write failed\n");  in bu21013_init_chip()
378 		dev_err(&i2c->dev, "BU21013_TH_OFF reg write failed\n");  in bu21013_init_chip()
385 		dev_err(&i2c->dev, "BU21013_GAIN reg write failed\n");  in bu21013_init_chip()
392 		dev_err(&i2c->dev, "BU21013_OFFSET_MODE reg write failed\n");  in bu21013_init_chip()
400 		dev_err(&i2c->dev, "BU21013_XY_EDGE reg write failed\n");  in bu21013_init_chip()
407 		dev_err(&i2c->dev, "BU21013_REG_DONE reg write failed\n");  in bu21013_init_chip()
458 		dev_err(dev, "no device tree or platform data\n");  in bu21013_parse_dt()
485 	dev_err(dev, "no platform data available\n");  in bu21013_parse_dt()
509 		dev_err(&client->dev, "i2c smbus byte data not supported\n");  in bu21013_probe()
520 		dev_err(&client->dev, "invalid touch_pin supplied\n");  in bu21013_probe()
527 		dev_err(&client->dev, "device memory alloc failed\n");  in bu21013_probe()
539 		dev_err(&client->dev, "regulator_get failed\n");  in bu21013_probe()
546 		dev_err(&client->dev, "regulator enable failed\n");  in bu21013_probe()
557 		dev_err(&client->dev, "Unable to request gpio reset_pin\n");  in bu21013_probe()
564 		dev_err(&client->dev, "error in bu21013 config\n");  in bu21013_probe()
588 		dev_err(&client->dev, "request irq %d failed\n",  in bu21013_probe()
595 		dev_err(&client->dev, "failed to register input device\n");  in bu21013_probe()
684 		dev_err(&client->dev, "bu21013 regulator enable failed\n");  in bu21013_resume()
690 		dev_err(&client->dev, "bu21013 controller config failed\n");  in bu21013_resume()