145 		printk(KERN_WARNING "Board #%d (at 0x%lx) is out of range (1 <= x <= %d).\n",  in ac_register_board()
151 		printk(KERN_WARNING "Board #%d (at 0x%lx) conflicts with previous board #%d (at 0x%lx)\n",   in ac_register_board()
193 	printk(KERN_INFO "Applicom driver: $Id: ac.c,v 1.30 2000/03/22 16:03:57 dwmw2 Exp $\n");  in applicom_init()
208 			printk(KERN_INFO "ac.o: Failed to ioremap PCI memory "  in applicom_init()
215 		printk(KERN_INFO "Applicom %s found at mem 0x%llx, irq %d\n",  in applicom_init()
223 			printk(KERN_INFO "ac.o: PCI Applicom device doesn't have correct signature.\n");  in applicom_init()
230 			printk(KERN_INFO "Could not allocate IRQ %d for PCI Applicom device.\n", dev->irq);  in applicom_init()
251 			printk(KERN_INFO "ac.o: No PCI boards found.\n");  in applicom_init()
252 			printk(KERN_INFO "ac.o: For an ISA board you must supply memory and irq parameters.\n");  in applicom_init()
263 			printk(KERN_INFO "ac.o: Failed to ioremap the ISA card's memory space (slot #%d)\n", i + 1);  in applicom_init()
273 		printk(KERN_NOTICE "Applicom ISA card found at mem 0x%lx, irq %d\n", mem + (LEN_RAM_IO*i), irq);  in applicom_init()
277 				printk(KERN_WARNING "Could not allocate IRQ %d for ISA Applicom device.\n", irq);  in applicom_init()
291 		printk(KERN_WARNING "ac.o: No valid ISA Applicom boards found "  in applicom_init()
304 			printk(KERN_WARNING "ac.o: Unable to register misc device\n");  in applicom_init()
320 			printk(KERN_INFO "Applicom board %d: %s, PROM V%d.%d",  in applicom_init()
330 				printk(" S/N %d\n", serial);  in applicom_init()
332 				printk("\n");  in applicom_init()
371 			printk(KERN_INFO "Hmmm. write() of Applicom card, length %zd != expected %zd\n",  in ac_write()
393 	printk("Write to applicom card #%d. struct st_ram_io follows:",  in ac_write()
398 			printk("\n%5.5X: %2.2X", c, ((unsigned char *) &st_loc)[c]);  in ac_write()
401 				printk(" %2.2X", ((unsigned char *) &st_loc)[c]);  in ac_write()
405 		printk("\nstruct mailbox follows:");  in ac_write()
408 			printk("\n%5.5X: %2.2X", c, ((unsigned char *) &tmpmailbox)[c]);  in ac_write()
411 				printk(" %2.2X", ((unsigned char *) &tmpmailbox)[c]);  in ac_write()
415 		printk("\n");  in ac_write()
424 		printk(KERN_WARNING "APPLICOM driver write error board %d, DataFromPcReady = %d\n",  in ac_write()
509 		printk("Read from applicom card #%d. struct st_ram_io follows:", NumCard);  in do_ac_read()
512 			printk("\n%5.5X: %2.2X", c, ((unsigned char *)st_loc)[c]);  in do_ac_read()
515 				printk(" %2.2X", ((unsigned char *)st_loc)[c]);  in do_ac_read()
519 		printk("\nstruct mailbox follows:");  in do_ac_read()
522 			printk("\n%5.5X: %2.2X", c, ((unsigned char *)mailbox)[c]);  in do_ac_read()
525 				printk(" %2.2X", ((unsigned char *)mailbox)[c]);  in do_ac_read()
528 		printk("\n");  in do_ac_read()
545 		printk( KERN_WARNING "Hmmm. read() of Applicom card, length %zd != expected %zd\n",  in ac_read()
589 				printk(KERN_WARNING "APPLICOM driver read error board %d, DataToPcReady = %d\n",  in ac_read()
611 			printk(KERN_DEBUG "Looping in ac_read. loopcount %d\n", loopcount);  in ac_read()
649 				printk(KERN_WARNING "APPLICOM driver interrupt err board %d, DataToPcReady = %d\n",  in ac_interrupt()
657 				printk(KERN_WARNING "APPLICOM driver interrupt err board %d, DataFromPcReady = %d\n",  in ac_interrupt()
717 			printk( KERN_WARNING "APPLICOM driver IOCTL, bad board number %d\n",(int)IndexCard+1);  in ac_ioctl()
789 		printk(KERN_INFO "APPLICOM driver release .... V2.8.0 ($Revision: 1.30 $)\n");  in ac_ioctl()
790 		printk(KERN_INFO "Number of installed boards . %d\n", (int) numboards);  in ac_ioctl()
791 		printk(KERN_INFO "Segment of board ........... %X\n", (int) mem);  in ac_ioctl()
792 		printk(KERN_INFO "Interrupt IRQ number ....... %d\n", (int) irq);  in ac_ioctl()
804 			printk(KERN_INFO "Prom version board %d ....... V%d.%d %s",  in ac_ioctl()
816 				printk(" S/N %d\n", serial);  in ac_ioctl()
818 				printk("\n");  in ac_ioctl()
821 			printk(KERN_INFO "DeviceErrorCount ........... %d\n", DeviceErrorCount);  in ac_ioctl()
823 			printk(KERN_INFO "ReadErrorCount ............. %d\n", ReadErrorCount);  in ac_ioctl()
825 			printk(KERN_INFO "WriteErrorCount ............ %d\n", WriteErrorCount);  in ac_ioctl()
827 			printk(KERN_INFO "Process in read pending\n");  in ac_ioctl()
830 				printk(KERN_INFO "Process in write pending board %d\n",i+1);  in ac_ioctl()