430     PRINTK (KERN_ERR, "check_area failure: [%x,%x] - mail maintainer!",  in check_area()
511       	PRINTK (KERN_INFO, "dropped over-size frame");  in rx_complete()
1035     PRINTK (KERN_WARNING, "rejecting open with unspecified VPI/VCI (deprecated)");  in amb_open()
1141     PRINTK (KERN_ERR, "out of memory!");  in amb_open()
1281       PRINTK (KERN_ERR, "%s vcc=%p rxer[vci]=%p",  in amb_close()
1326     PRINTK (KERN_ERR, "attempt to send on RX-only VC %x", vc);  in amb_send()
1336     PRINTK (KERN_ERR, "sk_buff length greater than agreed max_sdu, dropping...");  in amb_send()
1348     PRINTK (KERN_ERR, "could not allocate TX descriptor");  in amb_send()
1529     PRINTK (KERN_ERR, "could not allocate queues");  in create_queues()
1533     PRINTK (KERN_ERR, "queues allocated in nasty area");  in create_queues()
1617     PRINTK (KERN_ERR, "bad queue alloc %p != %p (tell maintainer)", memory, limit);  in create_queues()
1736 	PRINTK (KERN_ERR, "%s", msg);  in decode_loader_result()
1859 	PRINTK (KERN_ERR, "self-test failed: %s", msg);  in sf()
1933     PRINTK (KERN_ERR, "Cannot load microcode data");  in ucode_init()
1976   PRINTK(KERN_ERR, "Bad microcode data (%s)", errmsg);  in ucode_init()
2046   PRINTK (KERN_INFO, "microcode version is %u.%u", major, minor);  in amb_ucode_version()
2104     PRINTK (KERN_ERR, "card reset failed!");  in amb_init()
2109       PRINTK (KERN_INFO, "failed to get loader version");  in amb_init()
2111       PRINTK (KERN_INFO, "loader version is %08x", version);  in amb_init()
2114 	PRINTK (KERN_ERR, "microcode failure");  in amb_init()
2116 	PRINTK (KERN_ERR, "failed to get memory for queues");  in amb_init()
2120 	  PRINTK (KERN_ERR, "adapter did not accept queues");  in amb_init()
2187 		PRINTK (KERN_INFO, "Changing PCI latency timer from %hu to %hu",  in setup_pci_dev()
2202 		PRINTK (KERN_ERR, "skipped broken (PLX rev 2) card");  in amb_probe()
2210 		PRINTK (KERN_ERR, "skipped broken (PLX rev 2) card");  in amb_probe()
2223 		PRINTK (KERN_ERR, "IO range already in use!");  in amb_probe()
2229 		PRINTK (KERN_ERR, "out of memory!");  in amb_probe()
2238 		PRINTK (KERN_ERR, "adapter initialisation failure");  in amb_probe()
2247 		PRINTK (KERN_ERR, "request IRQ failed!");  in amb_probe()
2320   PRINTK (KERN_NOTICE, "debug bitmap is %hx", debug &= DBG_MASK);  in amb_check_args()
2323     PRINTK (KERN_NOTICE, "no debugging support");  in amb_check_args()
2327     PRINTK (KERN_NOTICE, "cmds has been raised to %u",  in amb_check_args()
2331     PRINTK (KERN_NOTICE, "txs has been raised to %u",  in amb_check_args()
2336       PRINTK (KERN_NOTICE, "rxs[%hu] has been raised to %u",  in amb_check_args()
2343       PRINTK (KERN_NOTICE, "useless pool (rxs_bs[%hu] = %u)",  in amb_check_args()
2349     PRINTK (KERN_NOTICE, "rx_lats has been raised to %u",  in amb_check_args()
2399     PRINTK (KERN_ERR, "Fix amb_mem (is %lu words).",  in amb_module_init()