Lines Matching refs:output
5 output, vbi capture and output, radio receivers and transmitters and a software
7 testing capture and output overlays.
12 capture device. Each output can be an S-Video output device or an HDMI output
29 - Supports crop/compose/scale in any combination for both input and output
33 - Raw and Sliced VBI capture and output support
36 - Capture and output overlay support
84 device with webcam, TV, S-Video and HDMI inputs, a video output device with
85 S-Video and HDMI outputs, one vbi capture device, one vbi output device, one
107 device, the second two with just one video output device you would pass
134 are created for each video output device. At most 16 outputs can be
137 output_types: the output types for each instance, the default is 0x02. This defines
138 what the type of each output is when the outputs are created for each
140 gives the type and bit 0 maps to output 0, bit 1 maps to output 1, bit
141 15 maps to output 15. The meaning of each bit is as follows:
143 0: this is an S-Video output
144 1: this is an HDMI output
146 So to create a video output device with 8 outputs where outputs 0-3 are
163 vid_out_nr: give the desired videoX start number for each video output device.
169 vbi_out_nr: give the desired vbiX start number for each vbi output device.
204 ccs_out_mode: specify the allowed video output crop/compose/scaling combination
205 for each driver instance. Video output devices can have any combination
373 The video output device can be configured by using the module options
376 HDMI input, one output for each output type. Those are described in more detail
385 This output supports audio outputs as well: "Line-Out 1" and "Line-Out 2".
386 The S-Video output supports all TV standards.
388 This output supports all combinations of the field setting.
397 The HDMI output supports all CEA-861 and DMT timings, both progressive and
401 The initially selected colorspace when you switch to the HDMI output or
410 An HDMI output has a valid EDID which can be obtained through VIDIOC_G_EDID.
433 There are three types of VBI output devices: those that only support raw
437 The sliced VBI output supports the Wide Screen Signal and the teletext signal
440 The VBI device will only work for the S-Video output, it will give
441 back an error if the current output is HDMI.
561 The following controls are specific to video capture and output and radio
702 These controls are all specific to video output.
755 capture and output streams and for the SDR capture device except for the
813 output. It is currently not used for anything in vivid, but most HDMI
816 Transmit Mode: sets the transmit mode of the HDMI output to HDMI or DVI-D. This
879 The vivid driver supports looping of video output to video input, VBI output
880 to VBI input and RDS output to RDS input. For video/VBI looping this emulates
881 as if a cable was hooked up between the output and input connector. So video
900 until the video output has started. At that time the video output will be
903 - the input type matches the output type. So the HDMI input cannot receive
904 video from the S-Video output.
906 - the video resolution of the video input must match that of the video output.
907 So it is not possible to loop a 50 Hz (720x576) S-Video output to a 60 Hz
908 (720x480) S-Video input, or a 720p60 HDMI output to a 1080p30 input.
916 Bottom' when the output video is set to 'Field Alternate'. This combination,
938 output must be configured for sliced VBI. The VBI capture side can be configured
1013 Video output will also honor any data_offset that the application set.
1046 the output overlay for the video output, turn on video looping and capture
1081 Note: output overlays are primarily implemented in order to test the existing
1082 V4L2 output overlay API. Whether this API should be used for new drivers is
1085 This driver has support for an output overlay and is capable of:
1119 - Add support to loop raw VBI output to raw VBI input
1120 - Add support to loop teletext sliced VBI output to VBI input
1128 - Add support to loop from a specific output to a specific input across