Lines Matching refs:parameter
11 if it doesn't recognize a parameter and it doesn't contain a '.', the
12 parameter gets passed to init: parameters with '=' go into init's
28 Hyphens (dashes) and underscores are equivalent in parameter names, so
46 parameter is applicable:
139 KNL Is a kernel start-up parameter.
140 BOOT Is a boot loader parameter.
151 a trailing = on the name of any parameter states that that parameter will
163 parameter values. These 'K', 'M', and 'G' letters represent the _binary_
229 unusable. The "log_buf_len" parameter may be useful
479 Limit apic dumping. The parameter defines the maximal
483 The parameter valid if only apic=debug or
564 bulk_remove=off [PPC] This parameter disables the use of the pSeries
577 ca_keys= [KEYS] This parameter identifies a specific key(s) on
621 those clocks in any way. This parameter is useful for
768 upon panic. This parameter reserves the physical
839 parameter allows control of the order of pages that will
844 possible value is MAX_ORDER/2. Setting this parameter
858 parameter enables the feature at boot time. In
904 entry later. This parameter disables that.
909 MTRR settings. This parameter disables that behavior,
931 pass the driver to filter for as the parameter.
938 This parameter allows to specify an EDID data sets
1109 Using this parameter you can use more than 50% of
1110 your efi variable storage. Use this parameter only if
1124 Using this parameter you can do debugging of EFI memmap
1150 entry later. This parameter enables that.
1192 parameter will force ia64_sal_cache_flush to call
1199 Warning: use of this parameter will taint the kernel
1209 If no parameter is passed, ftrace will dump
1396 to maximum brightness. If this parameter is set to 0
1397 (default) and the machine requires it, or this parameter
1442 We also add it as printk module parameter, so users
1673 PCI device 00:14.0 write the parameter as:
1680 PCI device 00:14.0 write the parameter as:
1695 kernelcore=nn[KMG] [KNL,X86,IA-64,PPC] This parameter
1719 not using this parameter you use sysrq-g to break into
1758 kvm.mmu_audit= [KVM] This is a R/W parameter which allows audit
1833 If only DEVICE is omitted, the parameter applies to
1953 by LOG_BUF_SHIFT kernel config parameter. There is
1954 also CONFIG_LOG_CPU_MAX_BUF_SHIFT config parameter
2090 use. Use this parameter to scan for
2095 seconds. Use this parameter to check at some
2132 Leaving out the screen size parameter will not load
2137 LED. This parameter is not necessary when using the
2148 parameter allows control of the logging verbosity for
2171 movablecore=nn[KMG] [KNL,X86,IA-64,PPC] This parameter
2193 multitce=off [PPC] This parameter disables the use of the pSeries
2322 parameter to '1'.
2323 The default parameter value of '0' causes the kernel
2383 console_suspend, a printk module parameter to control
2450 xsave to save the states. By using this parameter,
2460 parameter, xsave area per process might occupy more
2740 noaer [PCIE] If the PCIEAER kernel config parameter is
2750 nomsi [MSI] If the PCI_MSI kernel config parameter is
2928 allocator. This parameter is primarily for debugging
3288 rcutorture.shuffle_interval parameter.
3459 If this boot parameter is not specified, only the first
3488 The parameter means the number of CPUs to show,
3614 Note: this parameter cannot be changed while the
3642 controller if no parameter or 1 is given or disable
3664 Ignore sysrq setting - this boot parameter will
3855 anything. Set this parameter to avoid log spamming.
4026 This is actually a boot loader parameter; the value is
4140 The default value of this parameter is determined by