Lines Matching refs:and
3 DataCommute/BRI and TeleCommute/BRI adapters only and any other use is
8 Speaking of guarantees, THIS IS BETA SOFTWARE and as such contains
9 bugs and defects either known or unknown. Use this software at your own
12 our own option and without warranty. If you choose to assume all and
27 1.2 What is different between this driver and previous drivers?
32 2.1 Unpacking and installing the driver
39 3. Beta Change Summaries and Miscellaneous Notes
45 upon ISDN4Linux available separately or as included in Linux 2.0 and later.
47 type including DataCommute/BRI, DataCommute/PRI and TeleCommute/BRI for a
49 source form and needs to be complied before it can be used. It has been
54 ISDN4Linux is a driver and set of tools used to access and use ISDN devices
55 on a Linux platform in a common and standard way. It supports HDLC and PPP
56 protocols and offers channel bundling and MLPPP support. To use ISDN4Linux
57 you need to configure your kernel for ISDN support and get the ISDN4Linux
61 and therefore can function across adapters. When an ISDN4Linux compliant
62 driver (such as ours) is loaded, all of the channels go into a pool and
66 1.2 What is different between this driver and previous drivers?
69 subtle and not so subtle functional differences from previous releases. These
73 versus between 16K and 64K. New methods for using the shared RAM
77 have been improved to better detect available shared RAM pages and
79 - Decreased loading time and a wider range of I/O ports probed.
81 the driver and at the same time doubled the number of I/O ports
85 the DataCommute/BRI, DataCommute/PRI and TeleCommute/BRI in any
89 the protocol parameters, faster negotiation time and a more
95 Before you can compile, install and use the SpellCaster ISA ISDN driver, you
96 must ensure that the following software is installed, configured and running:
98 - Linux kernel 2.0.20 or later with the required init and ps
116 2.1 Unpacking and installing the driver
126 4. Read the README and RELNOTES files.
128 5. Run 'make' and if all goes well, run 'make install'.
132 Make sure you read the scctrl(8) and sc(4) manual pages before continuing
133 any further. Type 'man 8 scctrl' and 'man 4 sc'.
140 Make sure the driver loaded and detected all of the adapters by typing
144 edit the file "/etc/modules/'uname -f'/'uname -v'" and insert the driver name
150 for more on this) and then type '/sbin/rmmod sc'.
186 - please open the isdn-hdlc file in the examples directory and follow along...
190 interfaces are created and two routes added between the channels.
192 i) using the isdnctrl utility, add an interface with "addif" and
194 ii) add the outgoing and inbound telephone numbers
198 v) to turn the callback features off, set the callback to "off" and
203 a specific IP address and point to point address
211 - please open the isdn-ppp file in the examples directory and follow along...
226 xii) take out (minus) VJ compression and bsd compression
236 - please open the isdn-mppp file in the examples directory and follow along...
241 i) using the isdnctrl utility, add an interface with "addif" and
244 iii) set the Layer 2 protocol to hdlc and the Layer 3 protocol to
249 vi) to turn the callback features off, set the callback to "off" and
253 viii) add a slave interface and name it "ippp32" for example
256 specific IP address and point to point address
269 3. Beta Change Summaries and Miscellaneous Notes
276 It was noted that in Beta Release 1, the module would fail to load and result
279 cases, this data field was NULL, and was left unchecked, so when it was